Question about 1992 Plymouth Sundance

1 Answer

94 sundance won't get up to speed or go over 35???

Ok I have changed the cap and rotor also the spark plugs and checked the catalic converter to see if that was plugged so I changed that then I put a new fuel filter in but still will not seem to get up to speed , someone please help if you know what else to do???????

Posted by on

  • Anonymous Mar 13, 2009

    Ok so my sundance is still doing the same thing as before and I checked the timeing and its all good does anyone think it might be the Fuel pump cause soon as it starts to lose power I press the pedal harder and it goes but it trys to shift from drive to neutral.....

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 118 Answers

Sounds like it jumped time. you should check the cam and crank timing marks.let me know if you need more info have a good day DB

Posted on Mar 07, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why my 94 Astro van will not fire


this generation of gm vehicles is easy to troubleshoot. the engine needs 3 things to run: compression, fuel, and spark. since you mention fire, i assume you have no spark.

disconnect any random spark plug wire and connect the end to a hei spark tester. crank engine and observe for spark. if you have no spark, disconnect the center terminal of the distributor cap and use the hei tester in the same manner. spark means cap and rotor bad or bad plug wireset. no spark means make more checks.

check for battery voltage and good ground on distributor. check for open or shorted ignition module or ignition coil windings. if power and ground is present and ignition coil tests ok, check for ignition pulses at coil primary. if you have no ignition pulses feeding the coil, change the distributor.

with that generation of vehicle, the ignition system will operate without help from the computer. don't even troubleshoot the guts of the distributor, if you change the cap, rotor, and anything else, it will be the same price as a remanufactured distributor, and might not fix the problem. if you troubleshoot a low volrage related issue (no pulses, shorted or open circuit, unstable timing, etc), change the whole thing.

Jul 29, 2016 | 1994 Chevrolet Astro

1 Answer

Vsc trac off check engine


Check for codes & diagnose the new problem with the VSC

Tune-Ups ! --remember those back in the early 1980's, some
25 years ago,your not up to speed,you only get spark plugs

Mar 26, 2014 | 2006 Toyota Camry

1 Answer

94 Nissan sentra xe 1.6 won't run after it warms up.


when it stops running check to see if your getting spark and fuel

Feb 22, 2013 | Cars & Trucks

1 Answer

I have spark at the cap but not to the sparks, already change rotr


Ok, heres how the spark works, coil, to cap,, along the rotor to the connection pins of the cap, to the spark plug wires,, and onto the plugs, inside the cap, make sure that the little center piece is hitting the center or the rotor, which goes out to the tip of the rotor,, that sends spark to the pins inside the cap,, now if your cap has any corrosion or tiny cracks,, that spark will go all over the place and not travel down its intended path, so clean off those contact pins in the cap, or replace it, if you have no spark to any of the plugs,, change the cap,, if its just to one or 2 , check the plug wires and the plugs themselves

Sep 28, 2011 | 1990 Ford Mustang

1 Answer

Well i changed the distributor cap and rotor and still having a problem getting the vehicle started and when i do get it started and you push the gas pedal to the floor it sounds like the the catalic...


HOOK VACUUM GAUGE TO INTAKE MANIFOLD,IF VACUUM GAUGE NEEDLE SLOWLY DROP TO 5 HGS YOU HAVE A RESTRICTED EXHAUST SYSTEM, EITHER MUFFLER PLUGGED OR CATALYTIC CONVERTER PLUGGED BURNED OUT.

Aug 12, 2011 | 1999 Chevrolet Blazer

1 Answer

94 royal begis to cut out, chugs at about 55


Replace the spark plugs and wires along with a distributor cap and rotor. Be careful to leave the old wires and plug wires connected to dist.cap, just remove dist. cap from the distributor and lay aside with plug wires on it then install rotor then new cap and proceed to replace each wire for cap and spark plug one at a time so you don't mix up the spark plug wire firing order. Cap laying to the side is used for reference purpose.

Feb 26, 2010 | 1994 Oldsmobile 88

2 Answers

1994 1.8 CC lancer has no spark Primary and secondary coils checked out ok Transistor checked out ok has power to coils when key is on Should spark????


So you're getting voltage to positive side of coils, but no spark at plugs? If you were to take the coil plug wire and hold it about 1/4 inch from engine ground do you get spark? (Use well insulated handles, don't touch metal) If yes, maybe plug wires, if no, does it have a control module? I'm not familiar with Mitsubishi, I've worked mostly on American cars.

Jul 05, 2009 | Mitsubishi Lancer Cars & Trucks

1 Answer

Changing plugs/wires made engine worse.


you shouldnt have to gap the plugs buy the pre-gapped bosch plugs i use them in all my z's If it sounds like your going 90mph but only going 30, check the catalic converter....If its not that( if its glowing red after driving for 20mins, or when you smack it with a hammer and it sounds like a rock its bad) It could be a timming issue or a distributer/ rotor/cap issue....Is it manual or auto.Is the check eng light on?

May 18, 2009 | 1992 Chevrolet Camaro

Not finding what you are looking for?
1992 Plymouth Sundance Logo

Related Topics:

108 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts

yadayada
yadayada

Level 3 Expert

63990 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...