Question about 1999 BMW 318 ti

1 Answer

On a 1985 318i bmw my o2 censor was cut in half and i cant find the other other side need a wiring diagram

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • BMW Expert
  • 206 Answers

If I remember correctly, the original plug connector location is by the battery. It is a small round black plug.

Posted on Mar 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Wire was cut to the crank sensor


re join it using solder and heat shrink not hard to do but if you have to add a bit of more wire in make sure that it cant get caught in the drive belts so it happens again

Mar 31, 2014 | 2001 Isuzu Rodeo

1 Answer

I REPLACED O2 CENSORES AND THE MAF CENSORE


Check wiring, animals love to chew them.

May 19, 2013 | 2000 Nissan Xterra

1 Answer

Where can i find a free wiring diagram for a 1997 bmw 528i


Visit the following website, they advised that they offer free radio stereo wiring diagrams for free, including Nissan. http://www.modifiedlife.com/1997-nissan-pathfinder-car-radio-stereo-wiring-diagram/------------------------------------------------------------------------------------------
FGtech V53

Mar 21, 2013 | Cars & Trucks

1 Answer

The car will crank but it will not start any suggestions??


Definitley NOT an O2 sensor(they don't even do anything for the startup).What happens if you shoot some starting fluid in it?

Oct 07, 2012 | 1997 Chevrolet Cavalier

3 Answers

I have a 1997 Bravada that has a bad oxygen censor and a bad caytalytic converter. Would both of these problems cause a misfire, and , wich sensor is in bank 2


Yes they can surely cause an misfire.

I cannot understand your statement "wich sensor is in bank 2"

If i am not wrong you are asking which sensor is present in bank 2 .

The 4th O2 sensor is located in bank 2

Mar 22, 2011 | 1997 Oldsmobile Bravada

1 Answer

Locate o2 censor for replacement (myself, ideally). list possible problems in task.


There should not be problems. The only thing is some can be taken off with a 22mm wrench but then some have to be removed with a O2 socket, which is a regular socket that has a cut out down the side for the wire to slide in. This is the major problem. Other than that , you can do this within no time. Be sure the sensors have anti seize grease applied. Also, aftermarket is just a good sensor as the OEM.

Apr 20, 2010 | 1991 Volvo 240

1 Answer

Chrysler 1996 town n country van lxi edition


the o2 sensors are near the exhaust manifolds one on either side. You must have over looked them

Jul 05, 2009 | 1996 Chrysler Town & Country

2 Answers

Bmw stalling


Try checking the fuel pressure valve & vacuum hoses, I'm unsure about your model, The fuel pressure valve has 2 very small rubber O rings & they over time perish - there are 2 types that I can recall - 1 is a sealed unit & the other has a Cir lip. If yours is that later when you remove that clip there is a larger rubber ring on the shaft - take note at what position that ring was facing on removal. Seal unti can only be replaced. Hope that helps, good luck

Jun 01, 2009 | 1999 BMW 328 Series

1 Answer

I have a x5 2001 bmw. i need to replace the o2 sensor downstream after the cat. i have located the o2 sensor thats needs to be replaced but cant find where its connected at the other end. can you help me?


it will be atached to the bulh head behind block. so a torch will be needed.y dont you get a univesel and splice the wires they are a hell of alot cheeper and do the same job

May 04, 2009 | 2005 BMW X5

1 Answer

I need to know where you would locate a o2 censor and 2 map censors for a 2000 Pontiac Grand Am..V-6? I have no idea where to even begin looking on the car.


The O2 sensors are found on the exhaust pipe. They screw into the pipe and has wires coming off of them. The MAP sensor has a 3 or 4 wire plug with a vacuum hose connected to it commonly found on the intake or firewall.

Jul 10, 2008 | 2000 Pontiac Grand Am GT

Not finding what you are looking for?
1999 BMW 318 ti Logo

Related Topics:

166 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

Fred Sops

Level 2 Expert

271 Answers

Al Clark

Level 2 Expert

290 Answers

Doberman

Level 2 Expert

246 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...