Question about 1999 Dodge Dakota

2 Answers

How do i remove the window crank from a 1999 dakota door?

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Go down to your local parts store and buy a window handle removal tool. It slides between the crank and the door panel. There is a spring clip that is in the handle that holds it onto the mechanisms post.
Take the tool and slide it around till you find the clip, push and the handle will come off.

Have fun

Posted on Mar 21, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Dodge Master
  • 61,037 Answers

Torx screw in the center of the handle

Posted on Mar 11, 2009

2 Suggested Answers

  • 193 Answers

SOURCE: gears are stripped on drivers door window crank 1999 honda civic

First you are going to have to purchase another window regulator. Then you will have to remove the door panel and all material until you can access the window regulator.

At this point I can't go further until I know if it has manuel windows or power windows, because each is an entirely different operation.
Bill

Posted on Nov 19, 2008

abauto
  • 353 Answers

SOURCE: How do I remove the window crank and the drivers

You need a tool to remove the clip behind the handle. It is called window and door handle remover tool.

6710d07.jpg

Posted on Sep 29, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to remove door panel with a manual window


screws in the armrest, clip on window crank, screw behind door handle and possible a screw behind a plug that is located to the inner or outer pane, then with a flat tip screwdriver gently pry around the outside of the panel then lift panel up and out. Good Luck Tim

May 22, 2011 | 2001 Dodge Dakota

1 Answer

Door panel removal


panel is on clips except for the interior handle and window crank handlec (if you have one), so grab a corner or edge and pull a little until it pops..

Nov 12, 2009 | 1995 Dodge Dakota

1 Answer

I need a left front door/window schematic on line for a 99 Dodge Durango. I need to see how to put it together.


Front Door
  1. Remove the door trim panel.
  2. Remove the water dam.
  3. Remove the inner and outer door belt weatherstrips.
  4. Lower the window to the full down position and align the glass regulator arm with the access holes in the inner door panel.
  5. Remove the front glass run channel.
  6. Remove the nuts attaching the glass channel to regulator arm.
  7. Separate the glass and lift it up and out.
  8. Disengage the power window motor wire connector from the door harness, if equipped.
  9. Loosen the bolts in slotted holes attaching regulator to door inner panel.
  10. Remove the bolts attaching window regulator to inner door panel.
  11. Remove the regulator through the access hole in the inner door panel.
  12. Installation is the reverse of removal. Tighten the nuts attaching the glass to the lift plate to 7 ft. lbs. (9 Nm).
3455a81.gif
Power window regulator mounting—Dakota, Durango

6125789.gif
Window regulator removal—Dakota, Durango

Posting more on next post for door panel removal and installation.

Oct 26, 2009 | 1999 Dodge Durango

1 Answer

1995 Dodge Dakota> Removing door panel. Can't remove Window knob.. have to replace locks(both sides)....easiest steps to replacing the locks??


Their are two options on removing the door crank-one the base of the crank top comes off where it is connected to the panel and if you pry slight with a thin tool it will expose where you can remove with either a torx or a nut driver-second option you must slip in door panel clip removal tool to relase the spring clip-these fly if you don't keep be careful. clip tools are at most auto parts store-by slighty spreading the door crank look down and you will see spring clip.Note it's either nut removal or spring removal.

Sep 17, 2009 | 1995 Dodge Dakota

1 Answer

How to remove air conditioner clutch on 1999 dodge dakota


you need the special tools to remove it but you dont need to evacuate the systems there is a bolt in the center like a crank bolt then follow the instructions to the puller

Jul 21, 2009 | 1999 Dodge Dakota

1 Answer

Removing window handle so i may reach the inside door panel


the window crank is held on by a c-clip. To get it off you take a medium sized flat tip screwdriver and slip it in between the back of the crank and the panel GENTLY or you will tear up the door panel.BAD. Pry the panel away from the crank and you should be able to see the c-clip, then use a small bladed screwdriver to pop off the clip. Some times,just take your time it aint easy but it will come off and your in buisness. to get it back on do the opposit and give it a smart pop and it will usually go right on. hope it helps.

May 18, 2009 | 2000 Dodge Dakota Quad Cab

1 Answer

2000 dodge dakota door panel


There are five screws to be removed, two of which are Torx bit. One is in the center of the door panel towards the top. One is behind the door latch handle. One adjacent to the side view mirror, and two along the bottom. There is an access panel along side the door latch handle you need to pop off with a screw driver. It is triangular in shape and about 5 inches long. Once that is removed you will see the door latch linkage to latch handle. Disconnect the linkage by unsnapping the plastic retainer off of the linkag rod and swing it so the rod can be lifted out of the hole. The window crank handle is a *****, you will need a dentist's pick or similar to remove a retaining clip just behind the handle but in front of the panel. The it is just an upward and outward movement on the panel and it should come right out.

Feb 28, 2009 | 1999 Dodge Dakota

1 Answer

Window crank handle on a 97 dodge dakota


Look for screws in door little pop outs then take backside of mirror off then pull out at the bottom of the door then around the sides lift up and out then take vapor barrier off then you can seeeverything else/ Please rate my response thank you very much

Jan 22, 2009 | 2001 Dodge Dakota

1 Answer

Cant take door panel off 1999 dakota


Hi my name is Allen!

The window crank must be removed also, after you remove it and all the screws, grab the door panel and pull straight upward with it, this will remove it from the door.

For further asistance you may reach me at FixYa!

Dec 27, 2008 | 1999 Dodge Dakota

1 Answer

How do you remove a window crank on a 2001 dodge dakota


you need to push in on door panel at same time in between the door panel and Handel their is a horse shoe clip you will need a "Mechanics DENTAL PICK! to pull it out to release the crank Handel! most part stores will carry that tool!

Dec 22, 2008 | 2001 Dodge Dakota

Not finding what you are looking for?
1999 Dodge Dakota Logo

163 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...