Question about 1989 Toyota Camry

1 Answer

Passenger brake light shorts with lights on - 1989 Toyota Camry

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 17 Answers

Replace the bulb socket.

Posted on Mar 07, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rear passenger running light doesnt stay on but turns on when you push the brake 2006 chevy silverado


They are a double element bulb. Its used for brake light n running lIght, and I believe also turn signal as well, replace lIght it should fix your problem. If it doesn't, then you have a bad connector or a short to ground

Nov 04, 2014 | Cars & Trucks

3 Answers

2011 ford feista se brake light out on drivers side. Running light and blinker work. Have replaced bulb and socket with same results what do I do now?


Did you try the passenger side brake bulb in the driver side socket (maybe the new lamp is bad)??

If it works, then the problem is either a bad ground connection / wire at / between chassis and the shell of brake lamp socket, or bad 12 volt wire at / between the common passenger 12 volt brake light wire in the harness to the center contact on the brake lamp socket.

My suggestion is if the brake lamp wire is ONLY for brakes - not the directional too, simply add a new wire spliced into the passenger side brake light wire and extend it to the brake light wire closest to the new socket that you recently installed on the driver side. Disconnect the vehicle brake wire from the new socket and wire nut it off or tape it up (so it can't short out if it somehow becomes energized again) and splice this new wire to the new socket.

Test & you're done!

May 21, 2014 | 2011 Ford Fiesta

1 Answer

2011 ford feista se driver side brake light out only blinker and running lights work have replaced bulb and socket with same results. Help


Did you try the passenger side brake bulb in the driver side socket (maybe the new lamp is bad)?? If it works, then the problem is either a bad ground connection / wire at / between chassis and the shell of brake lamp socket, or bad 12 volt wire at / between the common passenger 12 volt brake light wire in the harness to the center contact on the brake lamp socket. My suggestion is if the brake lamp wire is ONLY for brakes - not the directional too, simply add a new wire spliced into the passenger side brake light wire and extend it to the brake light wire closest to the new socket that you recently installed on the driver side. Disconnect the vehicle brake wire from the new socket and wire nut it off or tape it up (so it can't short out if it somehow becomes energized again) and splice this new wire to the new socket. Test & you're done!

May 21, 2014 | Cars & Trucks

1 Answer

The passenger side brake light, and passenger side (front and back) window control doesn't work is it a fuse?


Well, the short answer is no.
The lights and windows are are different fuses.
There's a slight chance you have a problem with a ground wire on that side, but I doubt the two problems are related.
I would check the light for power and ground, and look at the window switches for power and ground. The windows are powered thru the driver switch on most cars.

Jul 17, 2012 | 2004 Oldsmobile Alero

1 Answer

Possible electric short. Lights dim on occasion(all lights, including headlights), clock/radio display went out for a couple of weeks then came back on and now the rear passenger brake light is out. Also...


squeal sounds like lose alternator belt and that would make sense if belt sliping lights will dim rear brake light probley a bulb radios dispaly may have short or just going bad

Feb 17, 2010 | 2004 Pontiac Sunfire

1 Answer

Head light and tail light wont work


the headlight switch may have a short in it. replace switch and try again.

Feb 27, 2009 | 2003 Ford Windstar

1 Answer

Brake lights


your wires run under the carpet.get under it and trace your wires all the way to the back of car.you hve a short or open cicuit.

Nov 23, 2008 | 1988 Mercury Grand Marquis

1 Answer

Brake light stay on while foot is off of pedal


check the bulbs and the wiring there may be a short

Nov 12, 2008 | 2002 Chevrolet Blazer

1 Answer

Troubleshooting 1984 chrysler back brake lights


There is a contact (not short) between wire to brake light and to back light on passenger side, when you press the pedal, electricity is absorbed by barake light bulb and back light dim out. Check cables and connectors, if necessary follow back cables to battery.
If the contact is a short the back lights fuse will blow, I think it is a contact between same polarity cables, not a short.

Regards

May 16, 2008 | 1984 Chrysler Fifth Avenue

Not finding what you are looking for?
1989 Toyota Camry Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...