Question about 1997 Dodge Stratus

1 Answer

Need to find and replace crankshaft position sensor in 1997 dodge stratus

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Dodge Master
  • 2,984 Answers

If you have a 2.0 or a 2.4L engine, it is located on the bottom backside of the motor that faces the cab area. You need to jack the car to get to it because of the low ground clearance of the car. I have a 1997 Stratus and replaced mine already.

Ask if you have more questions.

c17hydro

Posted on Mar 08, 2009

6 Suggested Answers

tragedy lok
  • 266 Answers

SOURCE: We can not find the cranshaft position sensor on

should b on the driver side center bottom of axel

Posted on Sep 01, 2009

c17hydro
  • 2984 Answers

SOURCE: broke crankshaft position sensor

If you can get a magnet....use it to pull it out...has to be a stong one....like on the back of a audio speaker. That's the part that's stuck right? Is there any part of it sticking out?

Posted on Mar 14, 2009

  • 151 Answers

SOURCE: crankshaft sensor

2-0L-2.4L I-4 crankshaft sensor mounts to the engine block, behind the alternator, just above the oil filter. 2.5L V-6 crankshaft sensor mounts to transaxle just below the distributor.

Posted on May 07, 2009

polarcycle
  • 1392 Answers

SOURCE: 2004 DODGE STRATUS 2.7L, Location of Crankshaft Position Sensor?

it is located on the right side of the motor, in the trans area. Actually in the bell housing.

Posted on Jun 23, 2009

  • 5 Answers

SOURCE: Replacing Crankshaft Position Sensor 2005 Dodge

Dear,
Next time buy a Honda, you won't have trouble like this.

Allah Akbar!

Posted on Dec 14, 2010

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1997 dodge stratus wont start has no spark and no trouble codes.


The automatic shutdown (ASD) relay will turn off power to the coil(s) and fuel injectors if the PCM is not receiving a signal from the crankshaft position sensor. You can check the ASD relay, but the problem is almost always a crankshaft position sensor or the wiring/connectors between the PCM and that sensor.

Mar 29, 2017 | 1997 Dodge Stratus

2 Answers

Diagram of where a camshaft sensor is on a dodge stratus 2.4L 4 cylinder


2003 model
not confirmed
crank angle sensor might be near the stater motor on the block


26233366-qzmmc3ihqjw1j4mumdlnccct-4-0.gif

26233366-qzmmc3ihqjw1j4mumdlnccct-4-2.gif

Jul 07, 2016 | Dodge Cars & Trucks

2 Answers

99 stratus 2.5 v-6/no spark.will crank over.


CRANKSHAFT POSITION SENSOR - 2.5L

REMOVAL
  1. Remove speed control servo from driver's side strut tower.
  2. Remove crankshaft position sensor retaining bolt Crankshaft Position Sensor
  3. Pull crankshaft position sensor straight up out of the transaxle housing.
  4. (Disconnect crankshaft position sensor electrical connector from the wiring harness connector.
INSTALLATION - ADJUSTABLE All vehicles will be equipped with an adjustable crankshaft position sensor. This can be identified by an elongated mounting hole in the sensor.
NOTE: If the removed sensor is to be reinstalled, clean off the old spacer on the sensor face. A NEW SPACER must be attached to the sensor face before installation. If the sensor is being replaced, confirm that the paper spacer is attached to the face of the new sensor Crankshaft Position Sensor and Spacer
  1. Install sensor in transaxle and push sensor down until contact is made with the drive plate. While holding the sensor in this position, install and tighten the retaining bolt to 12 N·m (105 in. lbs.) torque.
  2. Connect crankshaft position sensor electrical connector to the wiring harness connector.
  3. Attach connector to heater tube bracket.
  4. Install speed control servo. Tighten nuts to 9 N·m (80 in. lbs.) torque.

May 19, 2012 | 1999 Dodge Stratus

1 Answer

2004 DODGE STRATUS 2.7L, Location of Crankshaft POSITION SENSOR?


it is located on the right side of the motor, in the trans area. Actually in the bell housing.

Jun 23, 2009 | 1996 Ford Taurus

1 Answer

My 2002 dodge stratus serges when i accerate. I


Sounds like a throttle position sensor, but the comp should be coding the error in any case. How did you know to replace the crank and cam sensor?

May 06, 2009 | 2002 Dodge Stratus

2 Answers

Broke crankshaft position sensor


go to parts store and buy a easy out set.. this tool will back out the broken half for you...keith...

Mar 14, 2009 | 1997 Dodge Stratus

Not finding what you are looking for?
1997 Dodge Stratus Logo

253 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

71043 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6981 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...