Question about 1995 Toyota Camry

1 Answer

How to remove the Harmonic Balancer on a 1995 Toyota Camry sedan?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Vice President:

    An expert whose answer gotĀ voted for 100 times.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

  • Expert
  • 104 Answers

4. REMOVE ENGINE BALANCER
(a) Uniformly loosen and remove the 6 bolts in several
passes, in the sequence shown.
(b) Remove the engine balancer and spacers
5. CHECK CONNECTING ROD THRUST CLEARANCE
Using a dial indicator, measure the thrust clearance
while moving the connecting rod back and forth.
Standard thrust clearance:
0.160 − 0.312 mm (0.0063 − 0.0123 in.)
Maximum thrust clearance:
0.35 mm (0.0138 in.)
If the thrust clearance is greater than maximum, re−
place the connecting rod assembly. If necessary, re−
place the crankshaft.
6. REMOVE CONNECTING ROD CAPS AND CHECK
OIL CLEARANCE
(a) Check the matchmarks on the connecting rod and cap
to ensure correct reassembly.

(b) Remove the 2 connecting rod cap nuts.

(c) Using a plastic−faced hammer, lightly tap the con
necting rod bolts and lift off the connecting rod cap.
HINT: Keep the lower bearing inserted with the con
necting rod cap.
.

Posted on Mar 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where is crank position sensor on a 1994 toyota 2.2liter 4cyl ?


Where is the crank position sensor on a 95 Toyota celica gt 2.2

search.aibing.cc/Where+is+the+crank+position+sensor+on+a+95+Toyota...
P1335, No Crankshaft Position Sensor Signal - Engine Running. ... 91 1991 ToyotaCelica GTS Engine Mount Right 2.2L 4 Cyl Genuine. ... 1990, 1991, 1992, 1993, 1994, 1995, 1996, 1997, 1998, 1999, 2000, 2001 . ... Powered by a 2.2-liter engine, the Celica now had ST and GT trim models. ... in 1986 and a 2.0-liter ...

Where is crank position sensor on a 1994 toyota 2.2liter 4cyl ...

www.fixya.com/cars/t26080657-crank_position_sensor_1994_toyota
31 mins ago - It is not behind pully nor in dist all videos show - Toyota Cars & Trucks question. ... Change a crankshaft position sensor on a 2000 eclipse.

toyota camry crankshaft sensor - ABMforum.com

abmforum.com/toyota-camry-crankshaft-sensor.html
toyota camry crankshaft sensor 99 camry crankshaftcamshaft position codes i got a problem with my 97 ... The car 96 toyota camry 2.2 liter 4 cyl. ... 1994 toyota camry 2.2L 257k miles Symptoms Car overheats Top radiator hose hot bottom cold ...

Toyota Camry 5SFE Engine Timing Belt, Water Pump and ...

hubpages.com > Autos > Do It Yourself Auto Repair
Jul 10, 2014 - The Toyota 5SFE motor is a four-cylinder, 2.2 liter, timing-belt-driven, double ..... Remove the lower timing belt cover with the crankshaft position sensor. ..... I've never, ever replaced the harmonic balancer on a 4cyl 5SFE.

1995 Toyota Camry LE 4 cylinder - YouTube

? 2:27
https://www.youtube.com/watch?v=7TW6hlUiHWQ
Sep 6, 2011 - Uploaded by jacasan2000

Feb 03, 2016 | Toyota Cars & Trucks

1 Answer

Bolt size for harmonic balancer 1995 Toyota Tacoma v6 3.4l


Harmonic
Balancer Toyota Tacoma dimensions are
approximately between 5-6 inches in diameter and
2-3inch wide,

Jan 07, 2016 | Toyota Cars & Trucks

1 Answer

How to install balance drive gear on crankshaft 2007 Camry 2.4


Remove old crankshaft pulley ( Harmonic Balancer), by putting sturdy socket,think its 19mm, or 3/4 " on the center crankshaft bolt, with a good size breaker bar, wedge the breaker bar in between the suspension, and drive axle, to keep the breaker bar from spinning, while, you now turn the key inside the car, to engage starter, to spin the crankshaft,which may take several attempts, of turning the key, and putting socket back on, they are very stubborn,to break the center bolt loose,
Then remove harmonic balancer, with a PULLER, which requires 2 bolts, in the threaded holes, one on each side of the now empty center bolt hole, autozone , advance, has these to loan out, only requires deposit, which they give back to you, when you return it.
Put square key in slot on bare crankshaft, slide harmonic balancer,(crankshaft pulley,while lining up the square key,and tighten crankshaft bolt.

Oct 24, 2014 | 2007 Toyota Camry

2 Answers

2000 toyota camry 2.2L harmonic balancer how-to removal and replacement?


Take the tire off where the side of the armonic balancer is,if you have a air compact gun it1s more ease,remember to take the serpentine belt off to,if you dond have an impact gun,find a long enohg to lock in plece in some place of the car,then carefully,crank the engine not to starter it,just enogh to loose the tight bolt of the balancer.

Oct 26, 2010 | 2000 Toyota Camry

1 Answer

Where is the knock sensor located? 2000 Toyota camry 4cyl


remove the intake manifold ,remove radiator ,remove radiator intake and outake housing, remove fan ,remove all belts: power steering, alternator and if you have a/c, remove harmonic balancer ,remove timing belt covers, remove timing belt remove intake housinng once you have remove all the above, your freaken engine will look naked, you can see the location of the knock sensor is locate in the engine valley

Jan 11, 2010 | 2000 Toyota Camry

1 Answer

How to remove the harmonic balancer on a 1995 dodge intrepid 3.5


There is a nut in the center of the balancer... loosening may require an "impact" or a sharp blow with a hammer to begin to loosen the nut. Once loose, you can use a harmonic balancer puller (rentable at a local rental yard) Since its a very tight fit you'll need the puller to persuade it loose from the crankshaft.... watch your knuckles...

Oct 14, 2009 | 1995 Dodge Intrepid

1 Answer

Which is number one piston on 4 cyl 1995 camry


Left (see diagram)
49b48f0.gif
Thanks for using FixYa - a FixYa rating is appreciated for answering your FREE question.

May 18, 2009 | 1995 Toyota Camry

1 Answer

1993 Geo Prizm Lsi Harmonic Balancer


Yes a harmanic balancer from tha corolla is the same thing. I had to do the same thing with my 95 geo. It works out to be a lot cheaper buying for a toyota than a geo.

Jan 11, 2009 | 1995 Geo Prizm

1 Answer

95 corolla harmonic balancer


It's a pain to fix. U do have to replace the entire harmonic balancer. For a description of what is involved, go to autozone website, enter your vehicle info, click on products and how to, then the letter H for harmonic balancer. Good luck!!! Curt

Dec 05, 2008 | 1995 Toyota Corolla

1 Answer

Toyota camry


It should be right hand threads.
fh

Jul 25, 2008 | 1998 Toyota Camry

Not finding what you are looking for?
1995 Toyota Camry Logo

487 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...