Question about 2004 Chevrolet TrailBlazer

1 Answer

Having trouble setting garage door opener to my 2004 trailblazer

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 497 Answers

1. Position vehicle within 10 feet of garage door- engine off and battery on.

2. Press/hold 2 outside buttons of Homelink transceiver until red indicator starts flashing rapidly, then release button. This should take about 20 seconds. This erases any previously learned codes.

3. Press/hold remote control and press/hold button of Homelink transceiver simultaneously. Slowly move remote control from 5" away to 1" away from Homelink transceiver. Release both buttons after red indicator starts blinking rapidly. This should take about 5 seconds. I discovered that the Homelink in my TL is a bit faulty because it took much longer to accomplish this than when programming the Homelink in my MDX. My TL's Homelink may "unlearn" it's code in the future and the needed proximity of the TL to the garage door may be much closer than desired until I get the Homelink fixed.

4. Press training button on garage door opener unit until the indicator lights illuminates- this should be immediate.

5. Within 30 seconds press/hold the Homelink button for 2-3 seconds until the red indicator starts flashing rapidly. Repeat a second time. It should now be programmed. Check it by pressing the programmed button on the Homelink receiver.

6. When programming more than 1 garage door opener unit, disconnect power from unit before programming more units. By not doing this the programmed unit could conflict with the unprogrammed units commands.

Problems:

1. The Battery in the garage door remote may be too weak to program Homelink. However, the battery may be strong enough to operate the garage door. One of my remote controls had a weak battery- my system was installed today, fresh out of the box. I had to use the second remote control for the programming of Homelink on my 2 vehicles.

2. Antenna on the garage door opener unit must be hanging down, fully extended.
source:chalkstar100 (fixya mate)

Thanks for using Fixya
Have a nice day!

Posted on Mar 07, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Windows and doors wont open close or lock


i have 06 trailblazer chev all discribed is same here what idid ,behind drivers seat
under pull seat are fuses 2 near door silver fuses I pulled them out and put back and windows and door worked only for it will happen again I will replace them and find out if it is the trouble u could try same if it helps

Jun 07, 2012 | 2004 Chevrolet TrailBlazer

1 Answer

How do i open the hood? How do we set the garage door opener to work?


the handle is a small square under the dash drivers side next to door jam if u open drivers door kneel on ground look under bottom of dash bam! there it is. to set garage door fold down drivers visor and u will see three small buttons pick one don't matter, now hold down your hand held garage door opener button(close to the visor) and one of those buttons u picked until flashing light starts flashing rapidly (20) seconds. thats it done !!!if this doesn't work i will have to give u the rolling code instruction, let me know

Mar 18, 2011 | 2004 Toyota Avalon

2 Answers

My 2004 tralblazer a/c will blow out the floor when you put it on the dash vents why?


The heater / a/c vents are controlled by vacuum,or electronic devices. What is happening in your Trailblazer is the Vent Doors are either stuck in a open or closed position thus only having air flow to the floor vents only..The actual vent door is located in the heater box next to the blower motor.

Feb 19, 2011 | 2004 Chevrolet TrailBlazer

1 Answer

'04 Nissan Altima can't be trained to open garage door.


Hello , you are probably not doing anything wrong. Some garage door openers will not accept some codes. My Toyota Tundra 2005 worked on my garage door , but my 2004 F250 would not. Quinn , Arizona

Jul 16, 2009 | 2004 Nissan Altima

1 Answer

Just moved, no garage remote, need to set the opener in my SUV.


The garage door opener is needed to use the HomeLink system that is in your vehicle. This design is so that no one can program theirs to gain access to your garage. You will have to obtain a working remote and it will have to be programmed at the garage door.

Jul 13, 2009 | 2004 Nissan Maxima

1 Answer

How can i program the garage door opener to my 2005 trail blazer?


Sorry, the process is simple but too lengthy to post here.

Goto homelink.com

They make the system and have very complete instructions you can download.

PLEASE NOTE: MOST but not ALL Brands / models of opener will work with this system.

Apr 04, 2009 | 2005 Chevrolet TrailBlazer

1 Answer

Setting garage door opener


Most openers are programmed the same. You normally program the house garage opener to accept the new remote. Your garage opener will have a button to press to add in a new remote. Normally you press this and then press the remote in the car and hold until your lights on your opener flash or the garage door closes. (check your manual on your garage door opener)

Mar 27, 2009 | 2005 Chevrolet TrailBlazer

1 Answer

The buttons for garage will not program in my Lexus RX 330 2004


The buttons inside the vehicle are syncronized/programmed with the operatus that physically opens and closes your garage door, not the operner... The garage door opener needs to have a "programming" feature switch that must be set to "programming" before you can program the buttons inside the car...

There are step by step instructions in your owners manual... This could be a 2 person operation...

I have a 2004 RX and had the same problem, simply because I didn't follow the instructions precisely..

Good luck...Oz

Mar 22, 2009 | 2004 Lexus RX 330

1 Answer

Home link system will not accept garage door code.


I purchased a Chamberlain belt garage door opener. It was great! The lease on my duplex ended and the landlord bought it from me.

I found that the best way to program my vehicle's HomeLink buttons (to read the remote) was to do the learning procedure in a parking garage. This way the signal is not interrupted by all the waves around us.

Jan 02, 2009 | 2001 Lexus ES 300

Not finding what you are looking for?
2004 Chevrolet TrailBlazer Logo

1,846 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

64034 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...