Question about 1992 Chevrolet S-10

1 Answer

My s10 puts

When i drive it around it puts. i want to know how to fix it.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 398 Answers

Check spark plugs and wires first?

Posted on Mar 07, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1988 s10 blazer 4.3 when put in drive or reverse it stalls, idles real low any time but after take off no problems anyone know how to fix this


may be you should make a diagnostic and you can do it in a garage or you can do it by yourself if you want to do it by yourself you need some tools and you can find some good ones here: spobd2.com

Jan 29, 2013 | Cars & Trucks

1 Answer

Unable to put the code in alarm for s10 1991 chevy truck and therefore truck does not start


I had a s15 with a 4.3 v6 had the same problem I had to send it to the dealer ship and have the computer flashed.Cost me around 65.00 bucks to fix plus a tow to dealer.

Apr 03, 2011 | Chevrolet S 10 Cars & Trucks

1 Answer

The truck has a horrible sound coming from the top of the motor, it is very loud and when driving between 45 and 55 feels like a jerking motion back and fourth any ideas what the problem could be chevy...


Try driving it at that speed with your foot slightly on the brake pedal. (enough to put the brake lights on). If your lock up torque converter is acting up, riding the brake will dis-allow it from locking. Do this to see if it might be a lock up converter issue. (They usually lock up for better gas milage around 45-50 miles per hour.)

Sep 08, 2009 | 2000 Chevrolet S-10

1 Answer

84 chevy s10 2.8L


if your pressure is too low this fix is quite expensive and not worth for older cars, so the first thing you should try to keep it running is to use THICKER OIL (W20-50 or such), + oil stabilizier (any good oil additive). I tried it in my Jeep,- helped right away.. Good luck

Jul 28, 2009 | 1984 Chevrolet S-10

1 Answer

1991 S10 blazer 4x4 4.3 popping coming from the front


the popping sound is the stabilizer links or the lower control arm bushings you can replace all bushings and both link kits for around 50.00 and the light is prob from the sensor on the transfer case or the front end i would remove and clean with dawn dishwashing liquid and put them back.

Jun 23, 2009 | 1991 Chevrolet S-10 Blazer

1 Answer

I have an 89 s10 blazer. i had to replace the


you must have not connected a ground wire when you put the pump back on.

Apr 14, 2009 | 1989 Chevrolet S-10 Blazer

2 Answers

97 s10 blazer cuts out and loses power while driving.


Had the same problem with by 1998 S10 a couple years ago. Changed fuel filter?? didn't work. Changed the fuel pump?? didn't work. Changed the fuel pressure regulator?? didn't work.

I was about to the end of my rope when I put a timing light on it and it showed firing on cylinders more then once a cycle. Turns out my distributor cap was bad and spark was jumping between contacts. When a spark is spread out over more then one cylinder, it doesn't fire correctly and that is causing it to bog out. Simple and a lot cheaper then all the other fixes I tried. Crank sensor was my next option though.

Feb 01, 2009 | 1997 Chevrolet Blazer

1 Answer

1984 s10 2.8 manual trans. flywheel causes engine to vibrate


no should be same engine. check your engine mounts and tranny mount. how bad a vibration? sometimes after installing engine the trans gets shifted around and if mount was worn it will allow it to hit crossmeber and vibrate.

Jan 16, 2009 | 1984 Chevrolet S-10

2 Answers

2000 chey blazer s10 wont go into 4 wheel drive


Need more information, but try to engage with engine at idle and transmission in nuetral and then slowly put into gear. Some vehicles will only engage 4wd system in D for Drive not the D with the circle around it for Over Drive, due to speed restrictions on the system. 4H is used for inclement weather and snow for highway use or cruising off road. 4L should only be used OFF road not on pavement and for slow speeds only. If that does not work put in drive and slowly move vehicle forward with 4wd switch engaged shift to nuetral while coasting and then put into a forward gear NOT reverse and it should engage, make sure you do not have locking hubs as well, I don't know many vehicles that have locking hubs as of late, but I could be mistaken. Hope this helps. Other post have also stated that the 4wd switch could be faulty, and can easily burn out.

Jan 10, 2009 | 2000 Chevrolet Blazer

Not finding what you are looking for?
1992 Chevrolet S-10 Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...