Question about 1990 Land Rover Range Rover

1 Answer

My brake lights are not working can you help

All my rear lights work but my brake lights ,,bulbs are good fuses are good can you help

Posted by on

  • clambumper00 Apr 25, 2009

    I have an 1997 SE7 Land Rover and the Brakes lights don't work and the 3Rd brake light stays on......

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 4 Answers

The foot brake switch which is right near the foot brake
unplug it cross the plug that came out of it with a wire
turn the key on check lights

the timmy g

Posted on Mar 09, 2009

6 Suggested Answers

  • 1 Answer

SOURCE: No rear brake light / turn signals on 2001 Chevy Cavalier

The problem is the turn signal/headlight/hazard switch assembly on the steering column which the brake light wiring runs through. The part is easy to change and cost about $50 at most parts stores

Posted on Sep 05, 2008

  • 2 Answers

SOURCE: 2001 v 70 volvo brake light

Hello. Check relay RMI5 in REM unit located in left side rear of cargo area. As you look at it it's to the right of the central electrical connector 5th from bottom. Matt

Posted on Oct 08, 2008

  • 1114 Answers

SOURCE: Left rear brake light stopped working but bulb and fuses are OK.

take the bulb back out have someone sit in car apply brake get your self a circuit tester and check to see if this circuit is carrying efficient 12 volt current! some times in cold weather these bulbs get hot with long period of breaking and when released condensate and rust begins and you get what you have perhaps bad socket! this would be a ideal location to begin and probably end,

Posted on Jan 03, 2009

  • 150 Answers

SOURCE: 2005 Toyota Sienna rear brake light problem.

have you checked the earthing continuity-if it's this other bulbs may also partly light when brakes used
otherwise-
Check continuity of live from center to lh & rh lights and/or is there a live at those lights

Posted on May 03, 2009

  • 718 Answers

SOURCE: Brake Light Doesn't

Yes. Look on the brake pedal lever under the dask. When the brake pedal is pressed the switch is engaged. This is easy enough to replace. If you see two switches, the other one is probably a switch to disable the cruise control.

Posted on May 08, 2009

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

99 Toyota camry,rear brake lights not working,is there a fuse box under hood?


put a prybar between seat and brake pedal and use a test light on the wire in trunk where bulbs are sometimes bulbs look good but aren't or you got wrong bulb. a test light will verify that and make sure test light lights

Feb 16, 2015 | Toyota Cars & Trucks

2 Answers

My additional brake light is not working i have tested the brake unit and that works is there a seperate fuse for this or is it all on one fuse for all the brake lights


The third or High Mounted Brake Light runs straight off the brake light switch on the brake pedal arm. You say you tested the "brake unit"? I assume you mean the third brake light assembly, and if you get power there when someone steps on the brake pedal, then the bulbs are bad.

The power flow for the brake lights goes like this: Fuse ->Brake switch -> Turn signal switch -> Rear lights. The only difference is, if you have a 3rd brake light in your rear window, that gets its power directly from the brake switch. It does not go thru the signal switch first. So, if you are having a brake light problem, and your fuses are good, check the 3rd light in the rear window, if it lights up (assuming the bulbs are good, no one ever changes them), then the problem is most likely in the turn signal switch, hope this helps!

Aug 28, 2011 | 2002 Ford SVT Focus

2 Answers

Center high-mounted stoplight is not working? Where is the relay?


If the two rear brake light are working on each side, then fuse and relay are good, check the bulb.

Jul 08, 2010 | 1997 Chevrolet Blazer

2 Answers

Driver side brake light doesnt work but other brake light does changed bulbs still does not work


Make sure the fuses are good.There is a fuse for left and right brake lights.The fuse blocks are under the hood and there`s also one under the drivers side rear seat.If the fuses are good then remove the rear lamp assembly and check the bulb.I believe there are 2 screws and then just pull lamp assembly out.Hope this helps.Good luck.

Apr 04, 2010 | 2002 Chevrolet TrailBlazer

1 Answer

1999 GMC Envoy: replaced both GE 3057 lamps in left rear light assembly. Lamps both light. However depressing brake pedal does not initiate brake light. The righ rear brake light does work. The high mount...


The high mount brake light has its own fuse, so check that first. The high mount bulb is generally a stabdard type (there may be more than one bulb) or you can replace with an LED. As for the left rear bulbs not working when depressing brake pedal, check the bulbs again for any spring that may be broken. If the bulbs are still good, make sure there is sufficient contact with the socket. If still not working, have someone check it out further.

Feb 15, 2010 | 1999 GMC Jimmy

3 Answers

The brake lights on my 1999 saturn sl do not work. The bar on the rear window functions. The bulbs and fuse is ok--what is the problem


does the third brake light work when braking ? the bar on the rear window? if not replace brake light switch on brake pedel

Jul 03, 2009 | 2000 Saturn SL

1 Answer

2005 chev trailblazer v6 4.2 rear side brake light dont work the top rear brake light works fuse 12 front works rear seat below fuse 16 and fuse 34 good bulbs good where do i check next


CHECK FOR POWER AND GROUND AT THE CIRCUIT BOARD FOR THE AFFECTED BRAKE LIGHT. IF THAT CHECK OUT GOOD THEN CHECK THE BULB CONNECTION FOR BURNED CONNECTORS, THIS IS A COMMON PROBLEM. LOOPING A TEST LIGHT FROM THE POWER TO THE GROUND CONNECTION AND HOLDING THE BRAKE PEDAL DOWN IT SHOULD LIGHT. IF IT DON'T THE CIRCUIT BOARD IS BAD.

May 16, 2009 | 2005 Chevrolet TrailBlazer

2 Answers

No brake lights but 3rd light works all fuses are good


Sounds like a broken wire somewhere.
Since the middle brake light works I would suspect it is somewhere in the trunk or close to the back seat.
Buy or make a tester. A 12v light with a clip on one wire that you clip to a good ground on the car the other wire with a sharp point. Turn the turn signals on then poke wire to rear lights until tester lights. When tester lights you know the break is somewhere inbetween the tester and the brake lights.

Hope this helps.

Stan

Apr 16, 2009 | 1985 Buick Skylark

1 Answer

Brake lights rear


You should check the fuses. There may be a separate fuse from the brake lights and the interior brake light.

Sep 12, 2008 | 1992 Cadillac Eldorado

2 Answers

Rear brake lights are not working


Hi,

There are a couple of probable reasons why the brake light are not working, they are:
  • brake switch - underneath the dash. It is activated when the brake pedal is pushed. It is a spring loaded switch and is normally off. If the sprin is defective/missing then the switch will not activate;
  • brake light fuse;
  • bulbs;
  • corroded bulb socket - most brake lights are integrated with the rear park lights. The bulb socket would have 2 contacts, try checking if they are clean and reaches the mate in the end of the bulb;
  • wrong installation - the bayonet socket of most park/brake lights combo are offset, there is a right and wrong way if installing it into the bulb socket;
  • loose wire - it would be required to trace the brake wire to where it joins the rear harness;
  • loose ground - same as above or a workaround is to wire an additional ground wire from the housing of the bulb socket to any screw that is connected to the body ground.
Hope this be of initial help/idea. Pls post back how things turned up or should you need additional information.

Good luck and kind regards.

Thank you for using FixYa.

Jul 29, 2008 | Mercedes-Benz CLK Cars & Trucks

Not finding what you are looking for?
1990 Land Rover Range Rover Logo

Related Topics:

327 people viewed this question

Ask a Question

Usually answered in minutes!

Top Land Rover Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

yadayada
yadayada

Level 3 Expert

70387 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6880 Answers

Are you a Land Rover Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...