Question about 1991 Mazda Protege

1 Answer

Botch job my car is not fix right. my clutch went out, i had it replace, went to get it. my car is not idling and my break is in freeze mode. and my check engine lights come on and later it might go out.

Posted by on

  • yadayada
    yadayada May 11, 2010

    what is the question here???

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 91 Answers

They most likely forgot to hook some wires back up i would bring it back to them and make them fix it.

Posted on Mar 30, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Car turns off when engaging clutch to a lower gear


Check the following:
- Thrust bearing, clutch.
TEST: Pull up the hand brake. Start the engine and let it at idle speed.
Depress the clutch pedal, put the car in 1st gear, while keeping the clutch pedal depressed. If the gear lever hesitates or produce any abnormal noise, replace the clutch thrust bearing.
- If the gear lever shifts smoothly, clean the throttle body, idle air control valve and perform idle speed learn learn procedure.
- Check the valve clearance.

Apr 11, 2014 | 1992 Toyota Corolla

1 Answer

Changed head gaskets now idling ruf


Should have spent to money and had a real mechanic do it. Fixing behind a botched repair adds costs...

Apr 03, 2014 | 2002 Dodge Grand Caravan

1 Answer

I own a 1995 Audi 90cs. My clutch peddle started being dead tell half way down then got preshure. Now there is no preshure and the peddle sticks to the floor. There was no slipping in the clutch so I


You need to replace the clutch slave.....Ii recently did mine, after the installation it was stuck too.......the way I fix it was I had a friend pumping the clutch by hand while I bleed it under the car, it took about 15-20 minutes before it got hard again.
Good luck!

Aug 01, 2012 | 1995 Audi 90

1 Answer

Replacing a clutch on a 2000 chevrolet prizm


Not a job you can do in your driveway

You need a lift to get the car up high enough
to remove the transaxle,after you break the front
suspension loose & remove the drive axles

$700.00 is not all that bad,considering all the work
& price of parts. BIG JOB

Jul 06, 2012 | 2000 Chevrolet Prizm

2 Answers

Fan blade pretty much exploded while i was driving the other day. Do i need to replace the fan clutch as well? I don't want to buy a new blade and have the same thing happen because the clutch is bad as...


replace clutch as well-could have been damaged when fan let loose --rough idle -bad fan would give u a vibration that could feel like it was running rough

Nov 02, 2009 | Chevrolet Blazer Cars & Trucks

4 Answers

87 suzuki samurai - What are the symtoms of a bad throw out bearing? *It has a new cable* I can't get cable to adjust anymore. While pushung clutch car makes sqeeking and chatter noise and acts like clutch...


The symptoms of a bad throwout bearing is a horrible noise that ONLY occurs when you are pressing on the clutch. And/or you have no clutch action at all - the car is either in gear or it's in neutral. Sounds just like your situation alright.

Usually bad throwout bearings damage pressure plate fingers to the point that they need replacing too. And while they are in there, they will want to replace the clutch disk too. And then lathe the flywheel flat again so that they don't have a repeat customer complaining about the lousy clutch $job$ he just got. Flat flywheels supposedly won't chatter on take off or clutch engagement, but it could be hose job where you get soaked as well.

I went this route once on a gremlin - $500. The only reason I paid up was that I had a real good job at the time, and then I've never been back either.

Aug 04, 2009 | 1987 Suzuki Samurai

2 Answers

My vauxhall vivaro van gear salecter has problem sellecting 1st 2


slave cylider is prone on this van the gear box has to be removed and new clutch fitted as the cylinder leakes fliud in the box get ride before it goes completly it is a very costly job!!!!!!!!!!! thanks jezza

Mar 03, 2009 | 2002 Volkswagen Eurovan

1 Answer

Hydraulic clutch no resistance


change the servo cylinder that will do the job, don't forget to bleed after replacement...

Dec 16, 2008 | 1993 Dodge Colt

Not finding what you are looking for?
1991 Mazda Protege Logo

Related Topics:

47 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

61292 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...