Question about 2000 Ford Taurus

1 Answer

REPLACING BELT ON MY 2000 TAURUS.HAVE BELT OVER ALL PULLYS,BUT LAST ONE ,DON'T KNOW HOW TO PULL BACK PULLY AND GET BELT ON AT THE SAME TIME.

Posted by on

  • Anonymous Mar 14, 2014

    how do i pull the tenion pully back to put belt on?

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 5,158 Answers

Locate the tensioner... you need a "breaker" bar with a 3/8 inch socket head... a rachet would do with a long enough handle. there is a square hole in the tensioner... you need to release pressure on the tensioner long enough to get the belt on.

Posted on Mar 06, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 Chevy Silverado squeaking from engine when motor is cold just started this


it is your belt it needs to be replace you can buy belt dressing spray to use but if you have lot of miles I would replace the belt good luck..

Oct 29, 2012 | Chevrolet Silverado 2500HD Cars & Trucks

1 Answer

How to change serpentine belt on 2006 buick lacrosse


Start by drawing a diagram of the belt routing. Serpentine belts normaly have 1 spring loaded tensioner (1 pully will have a nut or 3/8 or 1/2 inch drive hole) That will be the tensioner. get spanner or ratchet to fit & lever the tensioner away from the belt. Remove belt. fit new belt to most pullys except the easiest to get to, lever the tenioner back & fit the belt to the last pully, Check the belt is on all pullys properly & your done

Jun 28, 2012 | Cars & Trucks

1 Answer

1993 doge caravan belt replace


If you need to replace it, the diagram for the belt position should be under the hood near the radiator cap. You need to loosen the tensoiner pully using a socket wrench and and pull and hold the pully up and take the old belt off. To install the new one route the belt back through the pullys and pull the tensioner pully to slide the last part of the belt in place and let the pully down and it will hold the belt in place.

Dec 26, 2011 | Cars & Trucks

1 Answer

One of my pullys broke last night. Im trying to find a layout of my pullies so i can figure out which pully broke.


Both Gates and Dayton have good diagrams on their websites that show belt routing, but you'll need to know the engine information for your car. www.gates.com, and then use the parts locator. You need to click on the photo icon next to the serpentine belt listing. Best Regards, SJV

Jan 31, 2011 | 2000 Chevrolet Cavalier

1 Answer

Ho0w do you replace the power steering belt on 1996 dodge avenger


there should be a tension idler that has to be retracted to give the belt slack most has a 1/2 inch square hole in it for a break over bar to fit in it to realese tension however i have not delt with this particular model but most are the same also be sure to carefully look at how the belt pattern is or if it still has the sticker for belt routing on it realese the tension and slip belt off first pully making sure not to put yoru finger between the belt and the pully after the first pully has been cleared the the tensioner can be released and the belt removed then put new belt on all pullys but one at this point tensioner bust be realesed again ultill belt is plased on last pully be suer belt is inline with all pullys

Mar 27, 2010 | 1996 Dodge Avenger

1 Answer

Replacing Serpentine belt 1998 ford taurus


should show on fan shroud belt routing.
on idler pully there should be square hole for 3/8 ratchet to go in and turn to loosen belt, but you have to hold pressure on it to take belt off one pully.and also to put back on.
[watch your knuckles]

Dec 18, 2009 | 1998 Ford Taurus

1 Answer

How to change the serpentine belt on a 2002 GMC Sierra HD2500


Look for the belt tensioner pully. If you don't know what this is run the engine and look at the pullies.The one you want is the only one that will be moving up and down.This is the one that is spring loaded.Think it is drivers side top.It may have a square hole in the arm to put a ratchet in.Thinking 3/8" drive but may be 1/2" ,if there is not a hole then you will need a socket that fits on the center bolt of the pully.I will suggest a long handled ratchet or breaker bar,if you don't have one you can put a pipe over the handle of a short handle."cheater pipe"Put force on it so the pully comes up off the belt.If you don't have a belt routing sticker still on your radiator shroud draw one before you remove it.I think the belt comes off on the drivers side.when putting on the new one start at the crank pully,around the waterpump,then to all pullys on passinger side.The last one will be the alternator.Hold the belt down in front of the tensioner pully attach the ratchet and pull until you can slip the belt under the pully,Make sure the belt is properly seated in all pullys before starting.Helps if you have a spare set of hands.

Oct 29, 2009 | 2002 GMC Sierra

1 Answer

How to set timing marks when changing the timing belt 1995 kia sportage 2.0liter


There is a DOHC or SOHC (double or Single overhead cam engone. Both are Similar. Both have a notch on back side of crank pully that aligns with a tab on engine just above crank pully looks like a triangle with the tip near crank pully is rounded off. SOHC engines have an arrow on cam pully that aligns with a point at top of timing belt rear housing. about straight up at top of it. DOHC have an I and an E on the cam pullys I for INTAKE and E for EXHAUST. the I and E match up at same type points on top of rear Timing belt housing. When installing belt make sure you do not move pullys. put belt on starting with cam shaft (s) then down to crank on tension side which looking at motor will be the right side or Clockwise direction keeping it tight no, or EXTREEMLY little slack. then back up around tensioner. Tensioner should be the last pully to go around. Once on make sure timing marks still lline up.Adjust tensioner and. rotate engine BY HAND 4 times and re check marks.

Oct 09, 2009 | 1995 Kia Sportage

1 Answer

Where do I loosen my belt that is runs A/C on 2000 Toyota Sienna?


One of those "wheels" or TENSIONER PULLYS on your vehicle is the tensioner for the a/c compressor. You will need to look at it and see if there is an adjustment bolt behind pully. If there is, loosen center pully nut, then run adjustment bolt out to slack out the belt. Replace belt and reverse prosedure. DO NOT OVERTIGHTEN BELT,as you can damage pullys and or belt. Tighten to factory specs. Rule of thumb is pulling the belt out and check for slack. No more/less than one inch slack.

Jul 23, 2009 | 2000 Toyota Sienna

Not finding what you are looking for?
2000 Ford Taurus Logo

Related Topics:

141 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Ron Lankford

Level 3 Expert

5386 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...