Question about 2005 Ford F-150

1 Answer

Power window off track

How do i get the door panel off so i can fix the window

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 508 Answers

Remove the door panel and the armrest. Then you will need to slip a thin flat blade screwdriver under the panel and gently pry up to release the plastic keepers that attach the door panel. Then you can remove the panel and gain access to the window regulator and track. Be gentle prying out the plastic keepers so you don't damage the panel. Some of the keepers may break, but you can get more from Ford or your local parts house. These are a very common piece. Good luck.

Posted on Mar 06, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

When hit a small bump driver window glass rattles terrible. How can I fix it?


-Need to re tight bolts that hold the glass inside the door.


Good Luck


Mai lor

Aug 13, 2015 | Cars & Trucks

1 Answer

How do I put the driver side power window back on track and the door panel for my 2003 Nissan Altima 3.5SE?


R/R the inner door panel, slide the window back on track, reconnect the window transmission to the window, (or reinstall the trans) bolt everything back together (window motor, window trans to door etc.) Make sure the window is in the UP position. use the switch to raise the window & keep it up if all is back together before finally installing the door panel ( make sure the switch & other plugs are plugged in before the door panel is reinstalled.) Lights etc. Good luck

Sep 14, 2014 | 2003 Nissan Altima

1 Answer

How to fix power window


it sounds like something is broken behind the interior door panel. Where the window track is. Pull off the door panel and inspect. Replace broken parts and lube the track well before re-assembly. Good luck and I hope this helps you.

Nov 27, 2011 | Dodge Cars & Trucks

1 Answer

My Driver side window in a 2006 chrysler sebring sedan does not work. The other three windows work properly but slowly. Could you teach me how to fix this problem?


Andrew, it may have lost power to it due to a bad wire or a loose wire. Also, the window track bar may be broke or it may br off track. You have to take the panel off of the door to find out. Since your other three work, it is not a fuse. I am not familiar with the new panels. The old ones have screws on the outside of the panel and one for the door handle. It has to come off to fix the issue. Once you remove the panel, remove the plastic sheet and foam in the inside of the door. You will be able to look at the window after that. Test your wires for current and make sure none have came loose. Make sure the window is not off track and the window bar is at the bottom of the window. It goes down with the window and pushes it back up. Get a voltage reader and test the wires for power. If they have power, it is not the wires. 4 thumbs up is appreciated if you appreciate the reply. Andrew, don't hesitate to ask me a question. I am here to help you.

Feb 26, 2011 | 2006 Chrysler Sebring

1 Answer

How do you get the driver's door latch out past the window guide?


Remove all screws around the outer edge of the door panel. Carefully pry off the decorative cover behind the door handle and remove the torix screw. Lift up firmly on the door panel to remove. To reinstall, line up molded plastic hooks on back of door panel with notches in the door, push down to secure, reinstall torix screw, decorative cover and screws.
Also before you lift away the panel, you'll need to undo the electrical connectors for the power window and door locks

It is best to get the whole power window regulator assembly from the junkyard, which includes the power window motor. Cost should be no more than $40. Remove interior door trim panel by removing all screws and pulling up on the door panel. Unbolt existing window regulator assembly and slide guides from aluminum window track (you will have to uncrimp one end of track). Installation is the reverse of removal (remember to recrimp aluminum window track after reassembly). I did this repair in 45 minutes, power window worked like new. Good Luck!



Dec 12, 2010 | 1996 Chevrolet Monte Carlo

1 Answer

Rear passenger window right side off track


this problem is very easy to fix,,open door look for bolts or screws all around inside of door ,take them all off,then take door panel off ,,you will then see track with window on it loosen two track nuts ,fit window into track then tighting nuts ,put back on panel ,all screws bolts ,ect ect ,JOB DONE

Jun 18, 2010 | 2007 Dodge Nitro R/T New Cars

1 Answer

How to fix drivers window.the window just feel in to the door panel. it is a power window. WHAT WOULD BE THE PROBLEM.


window came of track inside door maybe rollers came out of place have to remove door panel to access

Apr 05, 2010 | 1991 Chrysler New Yorker

1 Answer

How do i fix my 1996 honda accord driver side window? When i roll down the window it falls off the track! they are manual, not power.How do I fix?


If you take the door panel off which there is only 2 to 4 screws holding in on and some clips in the back. pull the window to the top of the door and tape in place pull the track up and line track up with the window fully up and make sure to tighten track bolts on both the window and door bolts. hope that helps

Dec 10, 2009 | 1996 Honda Accord

1 Answer

Fallen driver's side window


probably need a new window regulator. ebay. 93 to 98 should fit.

Section 01-05: Trim, Interior 1998 Villager Workshop Manual
REMOVAL AND INSTALLATION Trim Panel(s), Door Front
Removal
  1. Disconnect the battery ground cable (14301) if equipped with power locks or power windows.
  1. swv~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use care when removing the front door inside handle escutcheon (22620). Failure to do so can result in damage to the component.
    Carefully pry off the front door inside handle escutcheon by inserting a standard 1/4 inch screwdriver between the top rear portion of the front door inside handle escutcheon and the front door trim panel (23942) .




  1. If equipped with manual windows, slip a clean shop rag between the window regulator handle (23342) and the front door trim panel .
  1. Pull the shop rag back and forth to release the window regulator handle clip.




  1. Remove the three cover caps and front door trim panel screws.
  1. Remove the one front door trim panel capped screws from the door pull handle.
  1. If equipped with power windows, remove the door pull handle. Disconnect the electrical connectors.
  1. Slide a flat-bladed tool behind each of the retainers and twist the tool to disengage the front door trim panel from the front door (20124) .
  1. Remove the front door trim panel.
Installation
To install, reverse the removal procedure.
---------------------------------------------------------
Window Regulator, Power Front Door
Removal
  1. Disconnect the battery ground cable (14301) .
  1. Remove the front door window glass (21410) . Refer to the front door window glass removal procedure in this section.
  1. Remove the two front door brace bolts and the front door brace.


    415712f.gif

  1. Disconnect the front window regulator electric drive electrical connector.
  1. Remove the four front door window glass regulator track bolts.

    67b6136.gif


  1. Remove the three front window regulator electric drive bolts.
  1. Remove the front door window glass regulator track and the front window regulator electric drive (23394) as an assembly through the opening in the front door (20124) .
Installation
  1. Install the front door window glass regulator track and the front window regulator electric drive as an assembly through the opening in the front door .
  1. Install the three front window regulator electric drive bolts. Tighten the front window regulator electric drive bolts securely.
  1. Install the four front door window glass regulator track bolts. Tighten the front door window glass regulator track bolts securely.

Apr 29, 2009 | 1998 Mercury Villager

1 Answer

Driver side window is off track and stuck about 75% closed


If your power window motor is not moving up or down at all inside the door panel, you will need a new motor.
If your window is stuck and will not move, it is the motor - it is bad.
If your window falls down into the door panel, the window is off track.
Replacing a window motor is an easy fix, get another one from an auto parts store and replace it.
Good luck!

Mar 12, 2009 | 1993 Honda Accord

Not finding what you are looking for?
2005 Ford F-150 Logo

Related Topics:

257 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...