Question about 1992 Jaguar XJ6

Open Question

1992 Jaguar XJ6 Sovereign 4.0 Purge Valve Replacement

I own a 1992 Jaguar XJ6 Sovereign 4.0 that needs a purge valve replaced. Where is it located? What is its purpose? How do I install it? Do you have a picture of it?

Posted by on

6 Suggested Answers

  • 21 Answers

SOURCE: purge valve

By the intake manifold, what size engine do you have?

Posted on Jul 02, 2008

  • 166 Answers

SOURCE: heating jaguar 1996 xj6 all works but no heat at all

due to the fact there is duel zone heating in these cars there is a heater control unit could a amplifier these tend to fail and you wont be able to get any heat a genuine unit is very expensive around $1500 but if you shop around you can get one for around $250 non genuine
then its just a matter of getting a jag tech to fit it

good luck

Posted on Dec 21, 2008

savdragon
  • 37 Answers

SOURCE: Mustang GT 4.6 EVAP Canister Purge Valve Location?

You will need to remove the right front wheel & wheel well liner. The canister purge valve is behind the cover. It should have two tube going into the bottom and one on the side near the top.
You can fix it!
If this helps you out please rate me!
Brett

Posted on Mar 19, 2009

lastech
  • 408 Answers

SOURCE: Instrument lights won't turn off

hi,seem lighting switch is grounded or wiring for cluster is grounded,if can remove the lighting switch disconnected the wire,see if light in cluster is off,switch or wiring must check,ty

Posted on Mar 29, 2009

  • 13 Answers

SOURCE: How do you replace the heater valve in a 1999 S Type Jaguar???

i am sure i posted this solution before the dual heater control valve is located looking front of car behind radiator left hand side low down very hard to get at probably better to get access from under car i have the same problem with my car i am trying to pluckup the courage to do it

Posted on Apr 19, 2009

  • 77 Answers

SOURCE: where is the purge valve located on a 2004 honda LX?

It is with a 2 wire Black connect located next to the throttle body. Locate the green cap on the evap hose and follow it to the throttle body and that is the purge valve.

Posted on May 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you replace the purge valve on a 1996 Mercury Couger


Hello Maria Lucio,

Best test & replace video I've ever seen...

96 cougar purge valve replacement Ask com YouTube Search

The whole search:
Ask com What Your Question

Rockauto parts price:
http://www.rockauto.com/en/catalog/mercury,1996,cougar,4.6l+v8,1198795,emission,vapor+canister+purge+valve+/+solenoid,4936
1996 MERCURY COUGAR 4 6L V8 Vapor Canister Purge Valve Solenoid RockAuto

Oct 18, 2016 | 1996 Mercury Cougar XR7

1 Answer

I have code P0443. How can I find out what is wrong?


OBD-II Trouble Code: P0443 Evaporative Emission Control ...

www.obd-codes.com/p0443
P0443 - Evaporative Emission Control System Purge Control Valve Circuit ... P0443 trouble code symptoms could be just an malfunction indicator lamp (MIL) ... But, it's also possible to have a lean condition or a rough running engine if the ...Missing: jaguar ‎xj6

P0443 OBD-II Code and Check Engine Light - Jaguar Forums - Jaguar ...

www.jaguarforums.com > ... > XJ XJ8 / XJR ( X308 )
Feb 24, 2014 - Anyone have an idea on where to look for this? Jaguar® Leasing Deals.... P0443 OBD-II Code and Check Engine Light-xj8-purge-valve. .... Newby with air suspension fault, philwarner, XJ XJ6 / XJ8 / XJR ( X350 & X358 ), 7 ...Missing: 1995

Error code p0443..Think dealer is on crack - F150online Forums

www.f150online.com/.../287418-error-code-p0443-think-dealer-crack.h...

Jan 01, 2016 | 1995 Jaguar XJ6

1 Answer

Where is purge valve located?


How to test and replace the EVAP Canister Purge Volume ...

? 13:49
https://www.youtube.com/watch?v=QnVUBYdFHGI
Mar 29, 2014 - Uploaded by CarsNToys
The EVAP canister purge control volume control valve is operated by a step motor for control of flow rate of fuel vapor fromEVAP canister.

How To Install Replace Vapor Canister Solenoid Purge ...

? 2:14
https://www.youtube.com/watch?v=TZ6ZB_acC9w
Sep 16, 2014 - Uploaded by 1A Auto Parts
http://www.1aauto.com/vapor-canister-purge-solenoid-valve-ac-delco- ... How To Test and Replace EVAP Canister Vent ControlValve P0446 ...

EVAP Purge Solenoid Removal - YouTube

? 4:24
https://www.youtube.com/watch?v=Xj605HENFno
Feb 26, 2008 - Uploaded by richpin06a
EVAP Purge Solenoid Removal Saturn S-series. ... How To Test and Replace EVAP Canister Vent Control Valve P0446 - Duration: 6:18. by ...


Dec 18, 2015 | Cars & Trucks

1 Answer

How do I repl the vent solenoid on my 2007 trailblazer 6 cyl. I believe it is located on charcoal canister


Sorry you wasted your money on parts you didn't need ! There is a very specific diagnostic flow to testing this DTC - diagnostic trouble code ! An tools needed , scan tool , vacuum gauge ! the vent solenoid has nothing to do with this code .
Connector End View Reference: Powertrain Control Module Connector End Views or Engine Controls Connector End Views

1

Did you perform the Diagnostic System Check - Vehicle?
--
Go to Step 2
Go to Diagnostic System Check - Vehicle

2
  1. Disconnect the purge pipe from the evaporative emission (EVAP) canister purge solenoid valve.
  2. Install a hand held vacuum gage to the EVAP canister purge solenoid valve purge port.
  3. Disconnect the EVAP canister purge solenoid valve harness connector.
  4. Monitor vacuum on the vacuum gage.
  5. Start the engine and allow the engine to idle.
  6. Increase the idle to 1,200-1,500 RPM.
Does the vacuum gage indicate an increase in vacuum?
--
Go to Step 8
Go to Step 3

3

  1. Connect the EVAP canister purge solenoid valve harness connector.
  2. Monitor vacuum on the vacuum gage.
  3. Increase the idle to 1,200-1,500 RPM.
Does the vacuum gage indicate an increase in vacuum?
--
Go to Step 5
Go to Step 4

4
  1. Turn OFF the ignition.
  2. Remove and then install the fuel fill cap.
  3. Turn ON the ignition, with the engine OFF.
  4. Observe the Fuel Tank Pressure Sensor parameter with a scan tool.
Is the Fuel Tank Pressure Sensor parameter within the specified value?
-0.5 to +0.5 in H2O
Go to Diagnostic Aids
Go to Step 6

5

Test the control circuit of the EVAP canister purge solenoid valve for a short to ground. Refer to Testing for Short to Ground and Wiring Repairs.
Did you find and correct the conditions?
--
Go to Step 9
Go to Step 8

6

Test for an intermittent and for a poor connection at the fuel tank pressure (FTP) sensor. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs.
Did you find and correct the condition?
--
Go to Step 9
Go to Step 7

7

Replace the FTP sensor. Refer to Fuel Tank Pressure Sensor Replacement .
Did you complete the replacement?
--
Go to Step 9
--

8

Replace the EVAP canister purge solenoid valve. Refer to Evaporative Emission Canister Purge Solenoid Valve Replacement .
Did you complete the replacement?
--
Go to Step 9
--

9

  1. Clear the DTCs with a scan tool.
  2. Turn OFF the ignition for 30 seconds.
  3. Start the engine.
  4. Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records.
Did the DTC fail this ignition?
--
Go to Step 2
Go to Step 10

10

Observe the Capture Info with a scan tool.
Are there any DTCs that have not been diagnosed?
--
Go to Diagnostic Trouble Code (DTC) List - Vehicle
System OK

Feb 28, 2015 | 2007 Chevrolet Trailblazer

1 Answer

Purge solenoid location 2008 torent


Evaporative Emission Canister Purge Solenoid Valve Replacement
Remove the fuel injector sight shield. Refer to Fuel Injector Sight Shield Replacement. Disconnect the engine wiring harness electrical connector (4) from the evaporative emission (EVAP) purge solenoid.
Remove the oil fill cap. Lift upward and remove cover from ball studs.
The purge solenoid is under the plastic cover on top of the engine .
Disconnect the EVAP pipe quick connect fitting (1) from the EVAP purge solenoid. Refer to Plastic Collar Quick Connect Fitting Service.
Disconnect the EVAP pipe quick connect fitting (2) from the EVAP purge solenoid. Refer to Plastic Collar Quick Connect Fitting Service. Remove the EVAP purge solenoid bracket bolt (3). Remove the EVAP purge solenoid.

the purge

Sep 20, 2014 | 2008 Pontiac Torrent

1 Answer

Trying to locate canister purge valve solenoid on vehicle


There is a canister purge valve & a volume control purge valve on your truck. The canister purge valve is on the evap. canister itself(at the rear of veh. near the fuel tank. The volume control purge valve is located in the eng. compartment, passenger side behind Battery. You didn't mention if it's a 4 or 6 cyl.

Aug 10, 2014 | 1996 Nissan Pickup

1 Answer

Code p0443


Fault Code:- P0443 Indicates a Power-train fault


The fault is generally due to a problem in the Emission Control area


Fault Description: EVAP canister purge valve circuit malfunction

Action of ECM:- ECM Default: - Canister purge inhibited - Adaptive fuel metering inhibited


After clearing the DTC, complete the Purge system monitor drivecycle
Check for a reoccurrence of fault DTC.


Possible Fault:- EVAP Canister purge valve to ECM drive circuit: open circuit, short circuit, high resistance EVAP Canister purge valve power supply circuit: open circuit, short circuit EVAP Canister purge valve operating vacuum hose leak / restriction EVAP Canister purge valve failure

Check fault codes here http://www.bluejag.co.uk/diagnosticcodes.php

Aug 22, 2013 | Jaguar X-Type Cars & Trucks

1 Answer

Po443


P0443 - Evaporative Emission Control System Purge Control Valve Circuit Malfunction

Possible causes- Purge Control Valve harness is open or shorted
- Purge Control Valve circuit poor electrical connection
- Faulty Purge Control Valve


This fault will never cause a no start condition.

Sep 24, 2012 | 2000 Jaguar S-Type

1 Answer

Where are the purge lines to the purge valve diagram


Hello! Here is the diagram you requested...#5 is the Pressure Control Valve (Purge Valve)...
(1)Throttle Body (2)EVAP Solenoid Valve (3)EVAP Vacuum Switch (4)EVAP Canister (5)EVAP Pressure Control Valve (6)Floating Roll-Over Valve (7)Fuel Tank
1_1_2012_1_34_25_am.png
Guru.Saailer

Jan 01, 2012 | 1996 Buick Roadmaster

3 Answers

Po446 evap vent code where is the evap vent located


Some might have an ses p0446, evap emissions vent circuit low. If you take it to the dealer they want 300-400.00 to fix the problem. GM has a service bulletin on this condition and have the updated part for 180.00, thats suppose to eliminate this issue.

Basically the problem is, the evap purge vent valve gets clogged with dirt, especially if the truck is used in dirty conditions. Well I figured there had to be a cheaper way to cure this problem.

Here it is:
1) find the location of the vent valve; its under the truck, locate the charcoal canister on the front of the gas tank and trace the vent line to the vent valve.
2) Take the bracket loose with a 5/8 wrench.
3) Spin the valve around so the side with the hole is facing you.
4) Take an air compressor and blow the vent valve out.
5) reinstall and clear the code and it's fixed.

Now I know the updated part from gm is supposed to keep the valve from clogging ever again, but why spend the money when all you have to do is blow out the vent valve every 50k-100kmi and save your $$$!

Subject: DTC P0446 (Restricted/Blocked EVAP Vent Path) Set, Service Engine Soon (SES) Lamp Illuminated (Replace Hose/Evaporative Emission (EVAP) Canister Vent Asm) #02-06-04-037A - (02/02/2005)
Models:
- 1999-2003 Chevrolet Silverado Models
- 1999-2003 GMC Sierra Models
--------------------------------------------------------------------------------
This bulletin is being revised to add model years. Please discard Corporate Bulletin Number 02-06-04-037 (Section 06 -- Engine/Propulsion System).
--------------------------------------------------------------------------------
Condition
Some customers whose vehicles are operated in dusty type environments, such as farming or mining off-road type applications, may comment about the illumination of the instrument panel SES light, with a DTC of P0446 (Restricted/Blocked EVAP Vent Path) being set.

Cause
Dirt and dust intrusion into the EVAP canister vent hose assembly, resulting in restricted air flow, may cause this condition.

Part Number 15086429 Hose Asm-Evap Emis Cnstr Vent


Removal & Installation
Purge Solenoid Valve-2.2L (L61) Engine
  1. Disconnect the evaporative emission (EVAP) canister purge valve harness connector.
  2. Disconnect the vacuum pipe from the EVAP canister purge valve.
  3. Disconnect the purge pipe from the EVAP canister purge valve.
  4. Remove the EVAP canister purge valve and bracket.
  5. Remove the EVAP canister purge valve from the purge bracket.
  6. Inspect for carbon release in the EVAP canister purge valve ports.
To install:
  1. Install the EVAP canister purge valve on to the purge bracket.
  2. Install the EVAP canister purge valve and bracket. Tighten the purge bracket nut to 71 inch lbs. (8 Nm).
  3. Connect the purge pipe to the EVAP canister purge valve.
  4. Connect the vacuum pipe to the EVAP canister purge valve.
  5. Connect the EVAP canister purge valve harness connector.
  6. Remove the air cleaner outlet resonator.
  7. Disconnect the EVAP canister purge valve harness connector.
  8. Disconnect the engine purge pipe from the EVAP canister purge valve.
  9. Disconnect the engine vacuum pipe from the EVAP canister purge valve.
  10. Remove the EVAP canister purge valve mounting bracket attaching bolt.
  11. Remove the EVAP canister purge valve along with the mounting bracket.
  12. Installation is the reverse of the removal procedure. Tighten the bracket bolts to 71 inch lbs. (8 Nm).

Purge Solenoid Valve-2.4L Engines
  1. Remove the front purge pipe from the evaporative emission (EVAP) canister purge valve.
  2. Remove the rear purge pipe from the EVAP canister purge valve.
    NOTE The EVAP canister may have released carbon particles, which caused this part to fail, and may cause damage to other components. Check the EVAP canister for loose carbon before returning the vehicle to service.
  3. Disconnect the EVAP canister purge valve electrical connector.
  4. Insert a screwdriver between the EVAP canister purge valve and the mounting bracket in order to release the lock tab.
  5. Remove the EVAP canister purge valve mounting bracket attaching nut, if replacing the bracket.
  6. Remove the bracket.
To install:
  1. Install the mounting bracket and the attaching nut for the EVAP canister purge valve. Tighten the nut to 71 inch lbs. (8 Nm).
  2. Slide the EVAP canister purge valve onto the mounting bracket. Make sure the lock tab locks the valve in place.
  3. Connect the EVAP canister purge valve electrical connector.
  4. Connect the rear purge pipe to the EVAP canister purge valve.
  5. Connect the front purge pipe to the EVAP canister purge valve.

Vent Solenoid Valve-2.2L & 2.4L Engines
  1. Raise the vehicle
  2. Loosen the EVAP canister vent valve hose clamp and slide the clamp down the hose away from the EVAP vent valve hose connection.
  3. Remove the hose from the EVAP canister vent valve.
  4. Remove the EVAP canister vent valve by placing a pry bar between the valve and mounting surface, and moving the valve forward.
  5. Remove the clip from the EVAP canister vent valve harness connector
  6. Disconnect the EVAP canister vent valve harness connector.
To install:
  1. Connect the EVAP canister vent valve harness connector
  2. Install the clip into the EVAP canister vent valve harness connector.
  3. Install the EVAP canister vent valve by pushing the mounts into the original holes.
  4. Lubricate the hose end with lubricant.
  5. Install the hose to the EVAP canister vent valve.
  6. Slide the EVAP canister vent valve hose clamp down on to the hose connection at the EVAP canister vent valve.
  7. Lower the vehicle.

Hope this help (remember commetn and rated this).

Apr 21, 2010 | 2000 GMC Jimmy

Not finding what you are looking for?
1992 Jaguar XJ6 Logo

Related Topics:

286 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jaguar Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21927 Answers

Raygin
Raygin

Level 2 Expert

322 Answers

yadayada
yadayada

Level 3 Expert

60541 Answers

Are you a Jaguar Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...