Question about 1999 Oldsmobile Intrigue

1 Answer

1999 Olds Intrigue electric windows

The driver's electric window door console switch will not control any movement of the driver's and the right rear passenger window. Checked the far right dash/door end fuse compartment. Fuses good. The other two windows operate normally.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 221 Answers

The switch could be bad or needs to be cleaned.

Posted on Mar 12, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you remove the right front door panel on a 2004 buick le saber


Did you test it or are you guessing just because it won't open or close ? How To Install Remove Front Door Panel Buick Lesabre 00 05 1AAuto com both right an left are the same .
Power Windows System Components
The following components are used to control the power windows:
?€¢
Driver Door Module (DDM)


?€¢
Passenger Front Door Module (PDM)


?€¢
LH Rear Door Module (LRDM)


?€¢
RH Rear Door Module (RRDM)


?€¢
Driver Door Switch Assembly (DDSA)


?€¢
RH Front Power Window Switch


?€¢
LH Rear Power Window Switch


?€¢
RH Rear Power Window Switch


?€¢
LH Front Power Window Motor


?€¢
RH Front Power Window Motor


?€¢
LH Rear Power Window Motor


?€¢
RH Rear Power Window Motor


?€¢
Class 2 serial data circuit


?€¢
Power door serial data circuit


?€¢
PWR WDO 30 Amp Circuit Breaker


?€¢
DRVMDL Fuse (10 amp)


Driver Door Switch Assembly and Driver Door Module logic, Driver Door Module internal driver operation


?€¢
PASS MDL Fuse (10 amp)


Front Passenger Door Module logic and internal driver operation


?€¢
RRDR MDL Fuse (10 amp)


Left Rear Door Module and Right Rear Door Module logic and internal driver operation


Do you know about computer controlled power windows ?
Power Windows Operation
The vehicle is equipped with power windows controlled by the door modules. Each passenger door window can be operated, either from a switch built into the driver door switch assembly (DDSA), or from a switch mounted locally to its associated door. The driver door window can be operated only from the driver door window switch built into the DDSA.
When a window is operated from the DDSA, the DDSA interprets the window switch signal as a specific window switch request and sends the information to the driver door module (DDM) via the power door serial data circuit. The DDM examines the request and checks to see if it has received any class 2 serial data messages from any of the other vehicle modules (i.e. ignition switch position) prohibiting the movement of the window. If the window being operated is the driver door window, and if no prohibitive class 2 messages have been received, the DDM then applies voltage and ground to the driver door window motor to move the window glass as requested. If the window being operated is a passenger door window, and no prohibitive class 2 messages have been received, the DDM sends the request, via the power door serial data circuit, to the appropriate passenger door module. The passenger door module then applies voltage and ground to the passenger door window motor to move the window glass as requested.
When a passenger door window is operated from the power window switch mounted locally to its associated door, the passenger door module first checks to see if the DDM has received any prohibitive class 2 serial data messages. If there are no prohibitive messages, the passenger door module powers the associated passenger door window motor.
Both front door windows have the express down feature. This allows the front door windows to be fully opened by momentarily pulling the appropriate window switch lever to the second detente and then releasing.

Oct 30, 2016 | Buick Cars & Trucks

2 Answers

Olds aurora 1999 all four power windows quit working at one time. power sunroof still works.


Then you have two possibilities. First, most likely. Wires have broken. Open the drivers door and at the front you will see a rubber boot from the frame to the door. This is where the wires like to break. Second would be the master switch failed. I have replaced one or two(in 30 years) that the switch completely died. Usually just one or two windows quit working.

Apr 13, 2016 | 1999 Oldsmobile Aurora

1 Answer

1999 olds intriuge driver side window fell down one day when i shut my door. my husband has a stick inside the door holding the window up.


  • Well this could be the window pop out of the little metal clamp that holds the window in place or the window 'regulator/motor/track completely went South.
  • You can remove the panel and have a look. It's one or the other.

  • If you have any questions you can ask here.
  • Hope this helps and thank you for using FixYa.
Regards, Tony

Aug 10, 2011 | 1999 Oldsmobile Intrigue

1 Answer

Instructions how to step by step replace ignition lock cylindor for an 1999 oldsmobile intrigue


1999 Oldsmobile Intrigue

IGNITION SWITCH AND LOCK CYLINDER REPLACEMENT

1. Disconnect battery
2. Disable Supplemental Restraint System (Airbags)
3. Remove traction control switch from rear of center console plate
4. Open console lid and remove screws at front of console
5. Pull console plate up to release clips and slide over shifter
6. Pull rearward to release clips retaining instrument panel accessory trim plate to instrument panel
7. Remove screws attaching radio to instrument panel
8. Disconnect electrical connectors and remove radio
9. Take down instrument panel hush panels and disconnect courtesy lights. Remove hush panels
10. Remove knee bolster and knee bolster bracket from driver's side below steering column
11. Remove screws from IPC trim plate
12. Pull out instrument panel cluster trim plate to release from retainers
13. Remove trip odometer and reset switch from IPC trim plate
14. Remove IPC trim plate
15. Remove screws from IPC and pull IPC out
16. Disconnect electrical connectors from IPC and remove IPC from the instrument panel
17. Disconnect ignition switch connectors
18. Turn ignition switch to the ACC position and remove park lock cable from ignition switch
19. Turn ignition switch to ON position
20. Depress and hold locking tab on right side of ignition switch with a small, flat-bladed screwdriver and pull ignition lock cylinder from ignition switch
21. Remove ignition switch bezel from ignition lock cylinder
22. Remove screws attaching ignition switch to bracket
23. Remove ignition switch through the IPC opening
24. To install, reverse procedure

Apr 04, 2011 | 1999 Oldsmobile Intrigue

1 Answer

Electric windows on my '98 Olds Intrigue don't work. What are the most likely reasons for this malfunction? I have no idea where to start.... Thank you.


Check inside the drivers door,where the wires go to the body.
Have so slice a **** in the rubber boot to see the wires.
Often from the drivers door being opened and closed the most,the wires at that point will break,if it's the feed wire none of the windows will work.Kinda tight there but you can repair them with a crimp connector.

Oct 21, 2010 | 1998 Oldsmobile Intrigue

1 Answer

How do i get into the switch of the electric window on an intrigu


Pop the whole switch assembly off by carefully prying around the rear edge and lift up:


2b5f0fd.jpg297c578.jpg
You don't have to remove the door panel.

Mar 20, 2010 | 2000 Oldsmobile Intrigue

1 Answer

I am going to replace window regulator cables on a 1999 oldsmobile intrigue does one cable pull the window up and the other pull it down or does both cables pull up and down need to know if one cable is...


I've done this on my 1999 Olds Intrigue for the drivers door. The regulator I had did NOT have cables. It had two flat metal plates and gearing that when the motor turned, the scissors like action raised or lowered the window. I bought a whole unit from Rock Auto online and found instructions online. a little time consuming, but heck it only cost me less than $100 for the unit and my time. about 2 hours. really helps to get 3M blue tape to hold the window while you're removing the old regulator and installing the new one.

Sep 03, 2009 | 1999 Oldsmobile Intrigue

2 Answers

1998 olds intrigue - Rear power windows do not work. What checks can I make to determine if it the switch or the motor or wiring problem?


If both windows don't work, it may just be a blown fuse.

There is a fusebox on the interior of the passenger side...open the passenger door all the way up, and look at the side of the console panel, between the glovebox and the door. There should be a "finger hole" for you to pull open. It may be VERY hard to get open. Here you will find the smaller fuses. A diagram of the contents are on the inside of both lids.

Jul 07, 2009 | 1998 Oldsmobile Intrigue

Not finding what you are looking for?
1999 Oldsmobile Intrigue Logo

Related Topics:

238 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

69244 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22026 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6817 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...