Question about 1987 Ford Bronco II

1 Answer

1987 ford bronco 2 turns over wont ignite loose distributor

Is the any other causes and what happens when distributor loose

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 111 Answers

If your distributor is lose than you need to check the timing. Pull a plug out and put the plug wire back on it. ground the side of the plug and see if you get any spark. It should be a bright blue. If there is spark than put the plug back in. But I would first check the timing.

Posted on Mar 06, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1987 ford bronco and it wont start. It turns over like it wants to start but wont. I thought it might have been the carburator but my friend checked and its not, so now I think its flooded. what...


Check to see if the spark plugs are getting voltage. Check your distributor and rotor and make sure the distributor cap is not cracked, and the rotor is making contact. You can use an inductive timing light or use a spark plug connected to one of the plug wires to and ground the base of the plug using a jumper cable (do not touch the plug when cranking). When cranking you should see a spark. If you do not it could be the coil or electronic ignition. If you see sparks then you need to check the fuel pump pressure.

Nov 16, 2010 | 1987 Ford Bronco

1 Answer

Spark plug wiring


Ford Pick-ups and Broncos 1987-1996 Repair Guide
To avoid confusion, replace spark plug wires one at a time.



3f891cd.jpg

Fig. 1: 5.8L engine-nl-> Firing order: 1-3-7-2-6-5-4-8-nl-> Distributor rotation: Counterclockwise

4d7cb6a.jpg

Fig. 2: 4.9L engine-nl-> Firing order: 1-5-3-6-2-4-nl-> Distributor rotation: Clockwise

4670971.jpg

Fig. 3: 5.0L and 7.5L engines -nl-> Firing order: 1-5-4-2-6-3-7-8-nl-> Distributor rotation: Counterclockwise

e2e0c7b.jpg

Fig. 4: 6.9L and 7.3L Diesel engines-nl-> Injection order: 1-2-7-3-4-5-6-8


I hope help you (remember rated this help) Good luck.

Oct 05, 2009 | 1994 Ford Bronco

3 Answers

Does my 1987 ford bronco 2 auto,4x4 have a timing


Belt, remove the the front plastic cover which covers the Timing Belt to see if the belt is stripped of teeth, same as the old Ford Pinto motor.. remove dist cap and watch rotor rotation, see if it is spinning... Ignition Modules are a major issue with those in that year also... check module also...

Sep 27, 2009 | 1987 Ford Bronco II

2 Answers

1987 ford bronco engine wont start


there is a two piece control module and pick up in distributor you could replace these or try a used distributor

Jul 23, 2009 | 1987 Ford Bronco

1 Answer

1988 Bronco 2 stalling out.


have te ignition module and stator been replaced? that is the common cause of this, and yes the engine being out of time can cause this stall out, when you time the engine remember you must remove the timing shorting bar at the distributor connector to the TFI ignition module or the timing will be severely retarded

Jul 17, 2009 | 1988 Ford Bronco II

1 Answer

Spark plug and cap wiring for 1985 ford bronco 2


When your facing the front of your bronco looking into engine compartment, on left hand side in sequence is 1, 2, 3 front to back. on right hand side it's 4,5,6, front to back. The distributor rotates clockwise. On the top of the distributor, is 1-4-2-5-3-6 starting at the little mark on the cap or TDC. Hope that helped.

Jan 04, 2009 | 1987 Ford Bronco II

2 Answers

Weak spark + 1988 ford bronco


check the voltage of the b+ terminal of the ignition coil (primary side) with a cheap multimeter while cranking. low voltage to the primary will cause low voltage on the secondary. also recheck all ground paths from the ignition module. ensure good connection from coil to module. note: new parts are not "known good parts" until it runs.--> IG.MOD.

Dec 17, 2008 | 1994 Ford Bronco

1 Answer

Ford Bronco 2, 4-wd, 6-cylinders, 1987


The first part of your question must be verified first. Is the engine still running or is it possably the starter motor that will not disengage?

Dec 02, 2008 | 1987 Ford Bronco II

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

136 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

63990 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...