Question about 2003 Isuzu Axiom

Open Question

2003 Isuzu Axiom intake manifold torque spec?

Have a 2003 Isuzu Axiom and need to know the intake manifold torque spec.

Posted by on

3 Suggested Answers

  • 1 Answer

SOURCE: I need timing specs for 3.5 2002 Isuzu Axiom

I have found that one can mark (Paint pen) the gears and teeth (One tooth and one corresponding belt rib) on each gear prior to removing the belt. You can then overlay the old belt on a new belt and mark the same spots on the new belt and then install the belt so your marks on the gears and belt line up as they did before you removed the old belt. Given that your timing was right to start with....if done correctly, this will work.

Posted on May 09, 2009

carsandcomps
  • 722 Answers

SOURCE: need torque specs for isuzu rodeo 3.2 intake

josephrloop,

Go to: http://www.autozone.com/autozone/ymme/ymmeYear.jsp?_requestid=552857

Here you can select the year, make and model.

I hope this information proves useful and helps you with your intake torque success.

Cordially,

carsandcomps
Guru @ Fixya

Posted on Apr 10, 2010

  • 365 Answers

SOURCE: do i need a torque wrench to replace my intake

you should use a torque wrench but if you tighten them by hand make sure that you pull them down reasonably tight and check them a few days later as they may need to be retightened

Posted on Jun 13, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

03 Dodge Intrepid intake manifold torque specs top & bottom is for 3.5 V6


Lower Intake:
  1. Use a skin coat of RTV silicone on both sides of the water passage ports (outer most holes) and put the new lower intake gaskets into place
  2. Hand tighten the 13mm head intake bolts and Torque the bolts , starting from the center and working your way out in a circular pattern
  3. Torque these bolts in a few small increments until they have reached 250 inch pounds of torque.
  4. Upper Intake Plenum:
  5. When installing the intake air plenum , be sure to catch the four center bolts and the two side bolts (stiffener brackets) before tightening , The center bolts should be torqued to 250 inch pounds .The fuel rail bolts should be torqued to 100 inch pounds

Jun 24, 2016 | 2003 Dodge Intrepid

1 Answer

What are the torque specs for intake manifold on a 1998 ford windstar


what are the torque specs for the head and intake as well as

www.justanswer.com > Ford
... as well as - 47. Find the answer to this and other Ford questions on JustAnswer. ...Intake Manifold Support to RH Cylinder Head, 40-55 Nm. Degas Tube to ...

infamous windstar 3.8L intake gasket - Car Forums and Automotive ...

www.automotiveforums.com > ... > Ford > Windstar
Feb 24, 2006 - infamous windstar 3.8L intake gasket Windstar Car Forums. ... In fact, I may have torqued them in sequence initially to a lower value and then again to the final value in sequence. ... Using the Ford manifold torque pattern pictures can be misleading. ... '96 through '98 use pretty much the same intake.
Intake torque specs ' FordForumsOnline.comwww.fordforumsonline.com > Ford Tech Forums > Engine & DrivetrainMay 7, 2010 - 2 posts - ‎2 authorsISO torque specs for the intake & plenum for a 98 Windstar...3.8 with the ... Our community is here to help you with any questions you have related to your Ford. ... Lower Intake Manifold to Cylinder Head Bolt 8-12 - (71-106).Torque Specifications - AutoZonewww.autozone.com/.../Ford-Windstar.../Specifications/Torque-...AutoZoneAutoZone Repair Guide for your 2004 Ford Truck Ranger 2WD 2.3L MFI DOHC 4cyl Engine Mechanical Specifications Torque Specifications. ... Ford Windstar 1999-2003 ... Bolts, Main Bearing Bolts, Rod Brearing Bolts, Crankshaft Damper Bolts, Flywheel Bolts, Manifold. Intake, Exhaust ... Vehicle: 2008 Ford F150, 98 Civic.

Dec 21, 2015 | 1998 Ford Windstar

1 Answer

98 ford windstar intake manifold torque specs


Intake torque specs ' FordForumsOnline.com

www.fordforumsonline.com > Ford Tech Forums > Engine & Drivetrain

May 7, 2010 - 2 posts - ‎2 authors
ISO torque specs for the intake & plenum for a 98 Windstar...3.8 with the ... Our community is here to help you with any questions you have related to your Ford. ... Lower Intake Manifold to Cylinder Head Bolt 8-12 - (71-106).

Torque Specifications - AutoZone

www.autozone.com/.../Ford-Windstar.../Specifications/Torque-...

AutoZoneAutoZone Repair Guide for your 2004 Ford Truck Ranger 2WD 2.3L MFI DOHC 4cyl Engine Mechanical Specifications Torque Specifications. ... Ford Windstar 1999-2003 ... Bolts, Main Bearing Bolts, Rod Brearing Bolts, Crankshaft Damper Bolts, Flywheel Bolts, Manifold. Intake, Exhaust ... Vehicle: 2008 Ford F150, 98 Civic.

Dec 21, 2015 | 1998 Ford Windstar

1 Answer

WHAT IS THE TORQUE SPECS FOR INTAKE GASKETS


The torque specs are
-for intake manifold-to-cylinder head bolts/nuts
1996 and later-----132 in-lbs
-for intake manifold, upper to lower bolts
1995 and later-----89 in-lbs
-for cylinder head bolts
2001 and later----step 1--37
step 2--Turn an additional 120 degrees
I hope that this helps you out.

Jun 17, 2014 | 2003 Pontiac Grand Am

2 Answers

Need torque specs for a 2001 jeep cherokee intake manifold


Intake manifold using new gaskets. Torque the bolts, in sequence, to 105 inch lbs. (12 Nm)...

6a7ecad.jpg

Fig. Intake manifold torque sequence-3.7 & 4.7L engines


Hope this help (remember comment and rated this).

May 07, 2010 | 2001 Jeep Cherokee

1 Answer

Need torque specs for isuzu rodeo 3.2 intake manifold


josephrloop,

Go to: http://www.autozone.com/autozone/ymme/ymmeYear.jsp?_requestid=552857

Here you can select the year, make and model.

I hope this information proves useful and helps you with your intake torque success.

Cordially,

carsandcomps
Guru @ Fixya

Apr 10, 2010 | 2000 Isuzu Rodeo

1 Answer

Egr valve location isuzu axiom for a 2002


right rear of the engine on the top of intake manifold next to fire wall. long cylinder looking with a connector on top

Feb 25, 2010 | 2002 Isuzu Axiom

1 Answer

Replace thermostat on isuzu axiom


I just had a garage replace my thermostat on my 2002 Isuzu Axiom. The book calls for 2 hrs labor, no way. iI took the garage more like 5 hrs plus, they ate the additional 3 hrs of labor. Note, the intake manifold must be removed and even then special tools are needed because it is still buried deep down. The garage took pictures ot this one because of how ridiculours Isuzu designed the location.

Feb 01, 2009 | 2000 Isuzu Rodeo

Not finding what you are looking for?
2003 Isuzu Axiom Logo

Related Topics:

66 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...