Question about 2000 Chevrolet Malibu

1 Answer

Removing the glove compartment & replacing the blower resister.

I have a 2000 Chevy Malibu. I want to take out the glove box & replace the blower resister. Can anyone give me some help (not really step by step but easy enough for a novice to understand).

Posted by on

  • Anonymous Mar 15, 2014

    remove glove compartment box astro 2001

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 37 Answers

You do not need to remove the glove box to get to the resistor its located at the very bottom of the dash. Its held in by 1 or 2 screws. If you already bought the replacement look for the same thing underneath, a flashlight helps. Fairly simple, just have some patience. Its close the the blower motor.

Posted on Jun 20, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Finding blower motor in 2000 Chevy tracker


Finding blower motor ?
Could you please tell me where the blower motor is ?

It is behind the instrument panel compartment (glove box ).
1. Open the instrument panel compartment by pushing in on both sides to release the IP compartment door stops.
2.Remove the following components from the instrument panel:
2.1. The screw (1)
2.2. The instrument panel compartment (2)

Dec 31, 2016 | Cars & Trucks

1 Answer

I have to replace fan resister on my 2000 pontiac Montana do I to take out the blower motor to get at the resister


Step 1: Pry and remove the retaining pins (3) that secure the interior panel to the UNDERSIDE of the glove compartment area (near the PASSENGER'S feet).

Step 2: Disconnect the blower motor's wiring harness (1).

Step 3: Loosen and remove the 7/32 mounting bolts (3) that secure the blower motor to the vehicle. Pull the blower motor from the vehicle.

Step 4: Disconnect the wiring harness (1) mounted just to the LEFT of the resistor.

Step 5: Loosen and remove the 7/32 mounting bolts (3) that secure the resistor to the vehicle.


NOTE: You only need to LOOSEN the rear bolts, as the resistor will slide free without completely removing them!

Step 6: You can now slide and remove the resistor.

Step 7: Mount the new resistor by tightening the 7/32 mounting bolts (3). Connect the wiring harness (1).

Step 8: Reattach the blower motor by tightening the 7/32 mounting bolts (3).

Step 9: Connect the blower motor's wiring harness (1).

Step 10: Re-engage the retaining pins (3) to secure the interior panel to the UNDERSIDE of the glove compartment area.

Nov 12, 2016 | Pontiac Cars & Trucks

1 Answer

Remove golve compartment on 1999 chevy malibu


There's only so many screws that hold the glove box in. Some are inside the glove box and some are underneath. You may need a torx wrench depending on the type of screws holding the glove box in.

Feb 18, 2013 | 2000 Chevrolet Malibu

1 Answer

How do i replace a blower motor resistor on my 2000 chevy blazer? Should I be able to do it myself or should a mechanic do it.


it only has one plug ans a couple of screws.
it is under the big black cover under the glove box near the cabin air filter
the resister is attached to the fan box

Sep 12, 2011 | 2000 Chevrolet Blazer

1 Answer

How do you fix a fan sensor in a 2000 malibu


are you talking about heating fan resistor! if so, this is where and how its replaced. it is behind glove box. remove glove box so you do not have to stand on your head, only about 7 or 8 screws. then loosen and slide ecm to one side. ( but when removing glove box, remove insulator panel under glove box first ) now you can see heater blower and resistor. it is beside the fan, remove the wires from it. take out holddown screws, then pull it out. have a good holiday!!

Oct 08, 2010 | 2000 Chevrolet Malibu

1 Answer

I have a ford focus 2000 and is not blowing hot air from the first three levels only the fourth level works what is the problem?


You need to replace your blower resister.......... The blower resistor is located behind the glove box in the back left corner, follw the wiring harness to the resistor. there is one screw that holds it in place ( a little hard to get to ) unscrew and remove from connector. part is $15 but call different dealers because they price differently. PS squeze the sides of the glove compartment to drop the glove box down
I hope this helps you and please vote on this solution

Dec 30, 2009 | 2000 Ford Focus

1 Answer

2000 Chevy Malibu blower motor doesn't work on positions 1 & 2. Would appreciate details on how to fix or change it.


remove dash insulator from under glove box. then move bcm to one side, fan resistor is beside the fan blower motor. the resistor will keep fan speeds from working. remove wiring and screws from resistor then take it out.

Sep 08, 2009 | 2000 Chevrolet Malibu

1 Answer

Location of the Heat resistor in a 2003 Chevy Malibu?


Under the glove box, behind the blower motor itself. Remove the shroud below glove box, 2 screws and a snap-pop fitting. Be careful of the courtesy light. Remove the blower moter and disconnect the purple/black power connector to it - - you'll need this extra room to work with. 2 more screws, same size, 6.5mm on mine, 7or 8mm on some others, that holds the blower motor resistor in place. This replacement part is less than 40 bones at most parts store. Unplug, replace, re-install, test and you're on your way with about 2 hours of slow paced effort in your own driveway. Typical cost at a garage - up to $400, what a sham.

Feb 24, 2009 | 2003 Chevrolet Malibu

Not finding what you are looking for?
2000 Chevrolet Malibu Logo

432 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6879 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...