Question about 2004 Chrysler PT Cruiser

2 Answers

Dose anyone no wat thease codes codes meen as my car wont start but turning the key on an of a few times it brings up thease codes p1130 and p1685

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 11 Answers

P1130 HO2S Circuit Low Variance Bank 1 Sensor 1
P1685 Driver 5 Line 5 (Chip Set)

http://www.ptcruiserlinks.com/forum/general-turbo-discussions/14334-error-code-list.html

Hope this Helps

Posted on Mar 05, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 15,935 Answers

P1130 - HO2S Circuit Low Variance Bank 1 Sensor 1

P1685 - Skim Invalid Key - The engine controller has received an invalid key from the SKIM.

CLICK HERE for a full list of OBD Codes for the PT Cruiser.

Thanks for using FixYa - a FixYa rating is appreciated for answering your FREE question.

Posted on Mar 05, 2009

  • blueextc3221
    blueextc3221 Mar 05, 2009

    The SKIM code relates to your key.



    SKIM Operation

    When the ignition switch is moved to the RUN position, the SKIM transmits an RF signal to the transponder in the ignition key. The SKIM then waits for a response RF signal from the transponder in the key. If the response received identifies the key as valid, the SKIM sends a “valid key” message to the PCM over the PCI bus. If the response received identifies the key as invalid or no response is received from the transponder in the ignition key, the SKIM sends an “invalid key” message to the PCM. The PCM will enable or disable engine operation based upon the status of the SKIM messages. It is important to note that the default condition in the PCM is “invalid key.” Therefore, if no response is received by the PCM, the engine will be immobilized after two (2) seconds of running.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Chrystler 1999 300 m codes p1684 p0340 p1685 mean


P1684 CHRYSLER - Battery Power To Module Disconnected
https://www.autocodes.com/p1684_chrysler.html

P0340 CHRYSLER - Camshaft Position Sensor Circuit Bank 1 Sensor 1
https://www.autocodes.com/p0340_chrysler.html

P1685 CHRYSLER - Invalid SKIM Key https://www.autocodes.com/p1685_chrysler.html

Jan 08, 2017 | 1999 Chrysler 300M

1 Answer

What is error code P1685


P1685-invalid skim key-that means the key wheather its new or old is not programned to the car you cant just get any key cut it needs to be a skim chipped key and must be programed by a chrysler dealer to the car's skim module

Apr 07, 2014 | 2001 Chrysler PT Cruiser

1 Answer

Whining noise when trying to start my 1994 Concorde but it will not start


To start your car, it may need to be "jumped" by another car to jump start the battery, or you may need someone to bring gas for your car.-------------------------------------------------------------------------------------
Truck & Heavy Duty Diagnostic tool

Nov 18, 2012 | 1994 Chrysler Concorde

1 Answer

My 2002 pt cruiser died while I was driving first the oil light came on then it just died! I just had the oil changed 3 days prior to it dying some of the codes I received were 0340 1684 1685...


P0340 is cam position sensor. P1685 is for the key(has a chip in it) P1684 is battery has been disconnected. If the engine will still crank then codes P1684 & P1685 are probably old codes. So if the car will still crank, lets forget about those codes and focus on P0340 A bad cam position sensor will cause the engine to die and not allow it to start back up. Replace the cam position sensor and clear the code and the car should start up.

Oct 16, 2012 | Cars & Trucks

2 Answers

A.B.S LIGHT STAYS ON,& COMPUTER SHOWS FAULT CODE P1685,BUT I CAN`T DECIPHER THE CODE. CAN YOU HELP.


P1685 is:
P1685

Skim Invalid Key

The engine controller has received an invalid key from the SKIM.



You can get a full list of error codes from:

http://www.wjjeeps.com/faultcodes.htm

Jun 21, 2011 | 1997 Jeep Grand Cherokee

1 Answer

I have a 04 pt cruiser with airbag light and chime intermittent fault code p1685


p1685,,"skim invalid key"
I have no idea what they are talking about, but that is the code.

DTC P1685 is Invalid SKIM Key. The Sentry Key Immobilizer Module (SKIM) is part of the security system and kills the vehicle when a wrong key is used. There may be a problem with your key or the chip reader in the ignition switch. This is something the dealer will need to determine for sure. This code will also be set if someone actually tried to steal the vehicle.


My guesswould beto reset your PCM (unhook bat. and depress brake for 1 min), then try to start the car. If that doesn't work, I guess haul it into a dealership so they can run a diagnostic quote.gif

I got this from another site, check it out.

Aug 07, 2010 | 2003 Chrysler PT Cruiser

1 Answer

The key wont turn the ignition. What is causing


Could be a few things.. But try to eliminate the easiest & least costly first..
Spray some wd40 into the key hole..
Push key in & out several times & do not try to turn it yet..
Repeat a few times - then try to turn it..
Sometimes the key tumblers get dirty & sticky..

If that dose not help - it could be the ignition switch needs to be replaced..

Hope this helps !!
rate me good ;o)

Jul 13, 2009 | 1991 Dodge Dynasty

1 Answer

The engine turns over then it dies


Either your battery in the key is dead, or the key got wet and is hereby useless. I had to pay $250 to replace the key on my Magnum when that happened to me.

Apr 27, 2009 | 2001 Jeep Grand Cherokee

1 Answer

Codes


The car has tons of different codes for anything that is wrong with it. Without the numbers posted on your question it makes it impossible to say, but if you have a hayes or chiltons manual they have a full page giving aa description of each code the car can flash you.

Mar 05, 2009 | 2004 Chrysler PT Cruiser

1 Answer

2000 Lexus RX300 6cyl 3L VVT-i "Engine Codes"!


The first and last code are your start and stop so you can ignore them the P1130 and P1150 are your two front oxygen sensors( pre cats ) bank one and two. Depending on your millage it sounds like it is time for a little maintence. Normally they should be changed at or around 60,000 kms

Dec 12, 2008 | 2000 Lexus RX 300

Not finding what you are looking for?
2004 Chrysler PT Cruiser Logo

1,200 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

63456 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

chargerhp
chargerhp

Level 3 Expert

813 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...