Question about 1997 Dodge Ram 1500 Club Cab

1 Answer

Power steering Leakin from bottom hose.i believe It's the bottom hose if it is can i just throw a new hose clamp on it? Or is it high pressure?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 9 Answers

It should be a high pressure hose.

Posted on Mar 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Power steering hose diagram


power steering hoses run from pump to the steering box, (high pressure) and from the steering box to pump (low side).. is a closed connection. pump to box, then from box back to pump. High pressure should have pressed on fittings, while low side may have normal water hose clamps or replaceable hose without pressed on fittings.

Dec 16, 2013 | Cars & Trucks

1 Answer

Power steering leakin , but dont know where its coming from , and its whining too . but the it stops whining after i drive it for awhile , what should i do....


Whining should be low power sterring fluid.
Check the power steering dipstick and keep it in the range.
If you have no power steering fluid, automatic transmission fluid ( Dexron) works fine.
Leaks best found with a flashlight, you should not need the engine running, but you will need to get under the car, and you may need to push or bend some of the plastic sheilds out of the way to look.
Most often it is a hose, high or low pressure hose to the power steering pump that leaks.
High pressure hose has fittings, low pressure hose may have a hose clamp.

Jan 23, 2013 | 2001 Chevrolet Impala

1 Answer

How to change powerstering pump chevy uplander


I just finished replacing mine.

It is much easier if you do these steps:

1. Remove the serpentine belt.
2. Remove the nuts holding the main fuse box over the battery.
3. Remove the reinforcing bar over the battery.
4. Remove the battery.
5. Remove the windsheild washer tank.
6. Now you have access to remove the pump pulley. Without removing the stuff, it may be possible, but it will be extremely difficult.
7. Remove the pump pulley.
8. Loosen the high pressure hose fitting.
9. Remove the return line clamp.
10. Remove the power steering pump mounting bolts.
11. Remove the high pressure hose fitting.
12. Remove the power steering pump while sliding off the low pressure hose.
13. Remove the clips holding the reservoir on the pump.
14. Remove the reservoir.
15. Install new o-ring on the reservoir.
16. Install reservoir on new pump.
17. Install clips to hold reservoir on pump.
18. Install new o-ring on high pressure fitting.
19. Place new pump in position while sliding on low pressure hose.
20. Loosely attache high pressure fitting.
21. Tighten pump to mounts.
22. Tighten high pressure fitting.
23. Install clamp on low pressure hose.
24. Install power steering pulley.
25. Install washer reservoir.
26. Install battery.
27. Install reinforcing cross member.
28. Install fuse panel.
29. Install serpentine belt.
30. Bleed the power steering system.

Dec 13, 2012 | 2008 Chevrolet Uplander

2 Answers

Replace power steering pump on 06 chevy uplander


I just finished replacing mine.

It is much easier if you do these steps:

1. Remove the serpentine belt.
2. Remove the nuts holding the main fuse box over the battery.
3. Remove the reinforcing bar over the battery.
4. Remove the battery.
5. Remove the windsheild washer tank.
6. Now you have access to remove the pump pulley. Without removing the stuff, it may be possible, but it will be extremely difficult.
7. Remove the pump pulley.
8. Loosen the high pressure hose fitting.
9. Remove the return line clamp.
10. Remove the power steering pump mounting bolts.
11. Remove the high pressure hose fitting.
12. Remove the power steering pump while sliding off the low pressure hose.
13. Remove the clips holding the reservoir on the pump.
14. Remove the reservoir.
15. Install new o-ring on the reservoir.
16. Install reservoir on new pump.
17. Install clips to hold reservoir on pump.
18. Install new o-ring on high pressure fitting.
19. Place new pump in position while sliding on low pressure hose.
20. Loosely attache high pressure fitting.
21. Tighten pump to mounts.
22. Tighten high pressure fitting.
23. Install clamp on low pressure hose.
24. Install power steering pulley.
25. Install washer reservoir.
26. Install battery.
27. Install reinforcing cross member.
28. Install fuse panel.
29. Install serpentine belt.
30. Bleed the power steering system.

Jul 08, 2012 | 2006 Chevrolet Uplander

1 Answer

On a 99 Olds Alero, in the return lines of the power steering hoses, which place does the high pressure hose attach to?


RETURN TURN LINE GOES TO THE LEFT OF RACK PINION AND HIGH PRESSURE HOSE GOES TO THE RIGHT OF RACK PINION.LOOKING AT POWER STEERING PUMP HIGH PRESSURE HOSE THICK HOSE SCREWS INTO POWER STEERING PUMP.WHILE LOW PRESSURE HOSE HAS A HOSE WITH A CLAMP THE LOW PRESSURE HOSE HOOKS TO TOP OF POWER STEERING PUMP.LOW PRESSURE DONT SCREW INTO POWER STEERING PUMP IT IS HELD IN PLACE BY A HOSE SMALL CLAMP.

Jun 24, 2011 | 1999 Oldsmobile Alero

1 Answer

How to change power steering hose on chevy k1500 1989?


there r two hoses for high pressure hose u will need either a 5/8 & or a 19mm flare hut wrench (tubing hose wrench)for low pressure hose use side cutter pliers to cut two clamps off at either end of hose, will need new low pressure hose and two clamps. don't forget to re-fill with proper p/s fluid

Jan 15, 2011 | 1989 Chevrolet K1500

3 Answers

How to locate and replace power sterring high pressure hose


the high pressure hose has a pressure fitting the low has a clamp

Oct 23, 2010 | 1999 Dodge Durango

1 Answer

Which hose is on the bottom of the power steering pump of a 1999 Oldsmobile Alero?


LOOKING AT POWER STEERING PUMP YOUR LOW PRESSURE IS THE HOSE WITH A HOSE CLAMP.THE HIGH PRESSURE HOSE IS BIGGER AND HAS METAL LINE ATTACH TO IT.

Feb 08, 2010 | 1999 Oldsmobile Alero

4 Answers

On a 1994 olds cutlass supreme SL can i put a regular rubber hose over a leak on the power steerings high pressure hose to buy myself time before i can afford to replace it? i plan on hose clamping it...


If it is a small leak you might be able to wrap it with a rubber hose and apply several clamps to put a band-aid on it. However, this is only temporary at best and could still cause problems depending on where it is leaking. One possible alternative to a new hose - if you take the hose to a shop like The Hoseman (or equivalent) they can rebuild the hose cheaper than buying a new one.

Jan 30, 2010 | 1994 Oldsmobile Cutlass Supreme

1 Answer

Need to replace high pressure power steering hose on 2004 Monte Carlo SS. Need tips to effectively do the job myself. Tools needed, tricks to make the job easier, what not to do...etc. Thank yiou so much...


Power Steering Line/Hose: Service and Repair
Pressure Hose
Power Steering Pressure Pipe/Hose Replacement (3.8L)
Removal Procedure
1. Place a drain pan under the vehicle.
2. Remove the accessory drive belt.
3. Raise and support the vehicle. Refer to Vehicle Lifting.
4. Remove the tire and wheel assembly.
5. The power steering pressure hose is the lower hose at the power steering gear.
Remove the power steering pressure hose from the power steering gear.
6. Remove the power steering pressure hose from the power steering pump.
7. Remove the power steering pressure hose from the clamps on the power steering gear.
8. Remove the power steering pressure hose from the vehicle.
Installation Procedure
1. Install the power steering pressure hose to the vehicle.
2. Install the power steering pressure hose to the clamps on the power steering gear.
Notice: Refer to Fastener Notice in Service Precautions.
3. Install the power steering pressure hose to the power steering pump.
^ Tighten the fitting to 27 Nm (20 ft. lbs.).
4. Install the power steering pressure hose to the power steering gear.
^ Tighten the pressure hose fitting to 27 Nm (20 ft. lbs.).
5. Install the tire and wheel assembly.
6. Remove the drain pan from under the vehicle.
7. Lower the vehicle.
8. Install the accessory drive belt.
9. Fill the power steering system with power steering fluid.
10. Bleed the power steering system.
11. Inspect the power steering system for leaks.

00d203e.jpg

Sep 15, 2009 | 2004 Chevrolet Monte Carlo

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

101 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...