Question about 2000 Nissan Quest

1 Answer

Need size plz

Hi! i need to know the size of the axle nut on a 2000 nissan quest and thread im sure its metric. Thanx

Posted by on

  • dragonstalke
    dragonstalke Mar 05, 2009

    the left front, thanx for responding so quickly

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Nissan Master
  • 4,369 Answers

Yes metric. Which axle nut? I will look up

Posted on Mar 05, 2009

  • gerry bissi Mar 05, 2009

    I assume you mean ut shown on drive axle shaft with cotter pin. Shop manual doesn't list size but I am working on my Villager (same van as Quest) now. I will tell you what size metric socket goes on it. Are you trying to buy nut or just remove it.



  • gerry bissi Mar 05, 2009

    I just tried to fit my 32mm socket on it. It's too small. I'm guessing it's 33 or 34 mm. Don't have those yet.

    You don't need the hole size too do you?

×

6 Suggested Answers

97crownvic
  • 28 Answers

SOURCE: how to replace or install a nissan quest 1997 axle

two axles, different for ach side. Passenger side has a carrier on the half shaft, driver side is one solid link. Loosen lug nuts, the you need a 36mm socket to loosen the center nut on the drive shaft, same for both sides. Remove the cotter pin and retainer before loosening the center nut. Jack up the vehicle and secure with jack stands. Remove wheels. Remove brake calipers and tie up out of the way. Loosen and remove lower strut bolts (2) and lower ball joint bolts (3). Swing center knuckle out and off the drive shaft. On passenger side, loosen carrier bolts (3) halfway up the drive shaft, above the exhaust pipe and crossmember. This is a pain on the 94, but easier on later models. The passenger shaft has two half shafts joined at the carrier. No retainer clip is used, so pull on the end of the shaft and it will come out. Iff the inner CV boot is puked, it will probably come out in two pieces. You may have to use a large screwdriver to pry the inner shaft out of the transaxle. The driver side does not use a carrier and will come out with a strong pull. It does use a retainer clip on the inside end of the driveshaft. You can get new driveshafts with cvs as an assembly at most auto parts stores Be sure the new driver side shaft has the new retainer clip on it. Assembly is reverse of dissassembly, but make sure to tighten everything up good.

Posted on Feb 26, 2010

  • 136 Answers

SOURCE: how do i changs axle shaft on a 2001 toyota echo?

To remove the axle, losen axle nut with tire on the ground if possable, much easier without air tools. Disconnect strut at top of spindle, outter tie rod, and lower balljoint. Using a prybar pop axle out of transaxle. Some of these steps may be alittle different for your vehicle, these are general directions. If you are compitent enough to do this job then these steps will get you through it. If these steps confuse you pay someone else to do it.

Posted on Aug 08, 2009

  • 566 Answers

SOURCE: front rotor nut

hi out of curiosity? are wanting to renew thebrake disc/rotor ? or the actual hub that rotor fits to ? as not usually necessary to have to remove hub to change rotor ? unless the rotor is bolted to hub from the rear ?

Posted on Nov 08, 2008

  • 4369 Answers

SOURCE: Im looking for a sliding door handle for a 2000 nissan quest van.

ebay has them all the time also, go here for help on Quests http://autos.groups.yahoo.com/group/villagerquest/

Posted on Jun 08, 2009

  • 632 Answers

SOURCE: how to change rear bearing mk 2 golf

If I'm not mistaken it's a 30mm

Posted on Apr 12, 2010

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What size is the Alternator adjusting bolt ?


Don't worry I'm sure you will get the solution of your problem, just check the link I attach.
Best Manuals

Sep 28, 2016 | 1997 Nissan Pickup

1 Answer

Have purchased a used hood to add to escort we bought w/o a hood.


I believe all escorts have metric threads, so your 5/16"-18 would strip the holes or bolts or nuts. Could you find another escort and "borrow" a bolt out of it long enough to identify it so you could buy some? If "push came to shove", you drill the holes a little bigger, and then just use nuts and bolts there instead of threading the holes.
God bless your efforts.

Jun 01, 2015 | Cars & Trucks

1 Answer

What size is the axle nut on a 97 jeep grand cherokee 4X4 5.2? Also what size are the E-torx on the back side of the hub?


my socket set goes to 1-1/4": and 36mm.
my e-torx kit has all sizes, one can need.
with no sets. you must measure them. it's not covered in the FSM.
only 175ft/lbs on the axle nut and need for a torque wrench that big.
kit 1:
http://www.sears.com/titan-tools-13-pc-e-torx-socket-set/p-00926107000P?sid=IDx01192011x000001&kpid=00926107000&kispla=00926107000P

the better question is ,is the axle nut SAE or metric.
most real Chrysler built are metric.
so that big nut, at that torque needs 1/2' drive
and the torque wrench to match.
id bet this covers that
http://www.harborfreight.com/13-piece-12-drive-metric-deep-wall-impact-socket-set-67904.html

you could off the hub cap and measure the nut, with a metric rule.
the external torx same. with a caliper measure the head.
then use the e-torx table to mach it.
bet the first ever to post that. its rare to ask.
most folks just have the 2 sets. ( a life time investment if ever there was)
here is the table i uses, if ever
http://en.wikipedia.org/wiki/Torx

good luck working with only 2 bits.

May 03, 2014 | 1997 Jeep Grand Cherokee

1 Answer

What size is the axle nut on 2007silverado4x4 1500


Hello,

You can find this specific information utilizing http://www.rockauto.com I looked under a Silverado 1500 and found the following: Thread Size: M14-1.50; Hex Size: 22mm; Conical Seat - 60degree; Zinc; Overall Length (In): 0.807; Open End Design: Yes; Steel

Sincerely,

Apr 08, 2014 | 2000 Ford Taurus

1 Answer

Axle nut size


Measure the nut & divide by .0395 to get metric mm

34,35 or 36 mm are the most common

Mar 18, 2014 | Cars & Trucks

1 Answer

Front axle nuts size for 2003 pontiac grand prix


2002 Grand Prix front axel nut holding on hub is a 33MM or 1 5/16 deep socket

Feb 08, 2012 | 2003 Pontiac Grand Prix

1 Answer

Bolt size for 1995 gxe nissan quest rear license plate


standard license plate screw from a dealership or parts store maby metric threaded as well call and ask them

Jun 27, 2009 | 1995 Nissan Quest

Not finding what you are looking for?
2000 Nissan Quest Logo

Related Topics:

231 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

63661 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21986 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...