Question about 1998 Chevrolet Suburban

1 Answer

Front wiper motor

Replacing wiper motor

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 337 Answers

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Ford explorer 1998 rear washer doesnt work but wipers and motor do any suggestions


unhook the hose at the rear wiper,test, maybe the nozzle is plugged, or hose bent.

Aug 25, 2012 | 1998 Ford Explorer

1 Answer

Front windshiled wipers not working.


blown fuse, faulty wiper motor or faulty wiper switch. Possible you got a bad new wiper motor if you replaced everything in the order you wrote it in.

Mar 12, 2012 | 2003 Ford Windstar

1 Answer

How to change front wiper motor on 2004 Pacifica?


  1. Disconnect and isolate the battery negative cable.

110569875 Front Wiper Module - Remove/Install

  1. Remove the wiper module.

110569873 Front Wiper Motor Mounting

  1. With wiper module on bench, pry apart the socket and ball joint at the end of the bell crank .
  2. Remove the three front wiper motor mounting bolts and remove motor from module/linkage.
INSTALLATION
  1. Position the wiper motor into wiper module and install the three front wiper motor mounting bolts.
  2. Press the socket and ball joint together on end of bell crank.
  3. Install the wiper module.
  4. Connect the battery negative cable.
  5. Verify vehicle and system operation.
  6. Close hood.
11_29_2011_8_57_53_pm.gif11_29_2011_8_58_14_pm.gif

Oct 16, 2011 | 2004 Chrysler Pacifica

1 Answer

My windshield wipers don't work but the rear wipers and washer works..do I need to replace the wiper motor? If so, where is it located and how do I replace it?


Check fuses, front and back wiper motors run on different fuses. Test for power and ground at front wiper motor wires. If you have power and ground there your wiper motor may be toast. Good luck

Sep 12, 2010 | 1997 Mitsubishi Montero Sport

3 Answers

How easy is it to replace the front wiper motor on a 2004 ford escape ? Where is it located ?



Front Wiper Motor
Removal & Installation

NOTE A new wiper motor assembly comes with the linkage arm installed.
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove the windshield wiper mounting arm and pivot shaft
    WARNING Do not remove the wiper motor linkage arm from the wiper motor assembly. If the arm is removed, the wiper arms may not park in the correct location.
    NOTE Use a suitable tool to separate the wiper linkage arm from the wiper mounting arm and pivot shaft assembly.
  3. Remove the 3 bolts and the wiper motor.

    7f7866e.gif

    Fig. Wiper motor and linkage

To install:
  1. Install wiper motor and bolts.
  2. Tighten wiper motor bolts to 10 ft. lbs. (13 Nm).
  3. Install windshield wiper mounting arm and pivot shaft.
  4. Check wiper operation.

Rear Wiper Motor
- Removal & Installation
  1. Remove the rear pivot arm.
  2. Remove the rear wiper motor shaft nut cover
  3. Remove the rear wiper motor shaft nut.
  4. Open the lift gate window.
  5. Remove the rear wiper motor cover trim panel.
  6. Disconnect the electrical connector.
  7. Remove the 2 rear window wiper motor nuts
  8. Remove the rear window wiper motor.

    79be491.jpg
    Fig. Rear wiper motor view-2008 model shown, other years similar

To install:
  1. Install rear wiper motor and tighten mounting nuts to 62 inch lbs. (7 Nm).
  2. Reconnect the electrical connector.
  3. Install wiper motor cover trim panel.
  4. Install rear wiper pivot arm tighten nut to 53 inch lbs. (6 Nm).
  5. Install shaft nut cover.
  6. Check wiper operation.

Good luck (remember rated this post).

Feb 25, 2010 | 2004 Ford Escape

2 Answers

Wiper not working ford galaxy m2


No solution sorry - mine have done exactly the same - will wipe front screen if you mess with the stalk - rear wiper works when you push the stalk forwards or backwards but no washer to either - have you found a solution? Kind regards - Andy

Jan 04, 2010 | 2005 Ford Futura

1 Answer

Driver's side wiper arm on my '93 Sidekick is not working


This is what I Found there was not any Illustration's with it looks Fairly simple, Good luck



FRONT
  1. Disconnect linkage assembly from wiper motor shaft.
  2. Disconnect electrical connectors from wiper motor.
  3. Remove wiper motor attaching bolts, then wiper motor.
REAR
  1. Remove wiper blade and arm assembly.
  2. Remove access panel on back door.
  3. Disconnect linkage assembly from wiper motor shaft.
  4. Disconnect electrical connectors from wiper motor.
  5. Remove wiper motor attaching bolts, then wiper motor.
Skill
Level
Mfg.
Warranty
Standard Wiper Motor Labor Replace Front B 0.7 1.0
PLEASE DONT FORGET TO RATE ME Thank You Much

Jan 20, 2009 | 1995 Suzuki Sidekick

2 Answers

I have a1992 ford explorer the front and rear wipers quit workin


check for power at the wiper motor. If power at the wiper motor but no wiper action then replace the motor. if no power at the motor then use a jumper wire and put power to the motor. Does motor run? if so check for open circuit in the wire someplace.

Dec 27, 2008 | 1992 Ford Explorer

Not finding what you are looking for?
1998 Chevrolet Suburban Logo

Related Topics:

63 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...