Question about 2001 Toyota Camry

1 Answer

Instructions on how to fix the LH exterior

2001 Toyota Camry driver's side exterior door handle, any instructions step by step on how to change it out on my own???

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I repair the exterior door handle on a 1999 Toyota Camry ? Will it be necessary to replace the entire door ?


No the door handle is easily replaceable. you do have to remove the door panel and roll the window all the way up. 2 10mm nuts inside the door cavity and one bolt on the door jam near the lock mechanism. These handles are made of plastic and degrade and break easily after 3 or 4 years. Every toyota owner has to deal with this at some point. I also recommend buying the new handles on ebay as opposed to the dealer. The aftermarket handles are better quality than the original and MUCH cheaper. They are ALWAYS available on ebay.

Aug 02, 2012 | 1999 Toyota Camry

1 Answer

Installation instruction for the inside drivers side door handle on a 1995 Toyota Camry


Here's a great video that will show you how to fix the inside door handle on your Camry.
Tony">

Jun 23, 2010 | 1995 Toyota Camry

1 Answer

2001 Toyota Camry - Removing driver interior door panel


you can take a screw driver and pry it off. Be careful if you have power windows, if it falls right off then it could pull the wires loose. The panels have clips that clip to the door. Therefore, the only way to get the panel off is to pry it off.

Mar 07, 2010 | 2001 Toyota Camry

1 Answer

How to replace the exterior door handle of a 2001 toyota camry.


you have to take the door panel out and there is two nut holding the handle from inside

Feb 27, 2010 | Toyota Corolla Cars & Trucks

1 Answer

How to replace outside door handle on 2001 toyota camry car


Remove the interior door panel, then the lock mechanism which should then reveal the screws or nuts that hold the exterior handle in place.

Nov 07, 2009 | 2001 Toyota Camry

2 Answers

Need instructios to repair 1997 Toyota Camry Broken Exterior Door Handle


Two 10mm bolts, or nuts, hold the handle on from inside the door. dont forget to remove actuating rod from old handle. probably clip is broke also.

May 30, 2009 | 1997 Toyota Camry

1 Answer

Replace driver side mirror on 2001 Nissan Quest


SECTION 501-09: Rear View Mirrors 2001 Villager Workshop Manual REMOVAL AND INSTALLATION Mirror —Exterior Rear View Removal
  1. Remove the front door trim panel. For additional information, refer to Section 501-05 .
  1. Remove the upper speaker.
    1. Disconnect the electrical connector.
    1. Remove the bolts.
    1. Remove the speaker.
  1. Position the watershield aside.
  1. Remove the exterior rear view mirror access panel.
  1. Disconnect the exterior rear view mirror electrical connectors.
    • Release the wiring harness locator.
  1. Remove the exterior rear view mirror.
    • Remove the bolts.
    • Feed the wiring harness through the door opening.

Mar 31, 2009 | 2001 Nissan Quest

1 Answer

Diagram for replacing exterior door handles


ok. first u remove the door panel(s), with the window rolled up, u will be able to see the back side of the exterior door handle. there will be three bolts, they are size 10metric. there is also a rod attached to the handle held in place by a plastic clip, remove the rod, then remove the three bolts. from the outside remove the exterior door handle being careful not to scratch painted surface. Repeat for the other door(s). Repeat this for installation.

Dec 14, 2008 | 1997 Toyota Camry

1 Answer

2001 Nissan Quest - Broken Exterior Sliding Door Handle


you can do this. you have to remove inside trim panel for access. if you still need to do, I will send you repair steps. let me know

Oct 16, 2008 | 2001 Nissan Quest

1 Answer

Replacement of Inside drivre side door handle


remove the plugs in the the handle. (the part that you hold to close the door),then unscrew should be 2 large phillips heads. remove window winder if not electric, remove plastic cover around door release handle. remove inner mirror trim. then remove door trim carefullly pull it towards you it should pop out every couple of inches around the edge. remove inner plastic .then remove handle from door and from metal rod should be a plastic locking clip just pop it too the side. fit new handle then reverse these instructions.

May 23, 2008 | 1995 Toyota Camry

Not finding what you are looking for?
2001 Toyota Camry Logo

309 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...