Question about 2000 GMC Sonoma Extended Cab

1 Answer

Where is the camshaft position sensor located on my 2000 sonoma?

I'm not sure where the sensor is located.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 366 Answers

Its located in distri butor

Posted on Mar 07, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My truck sonoma gmc 2001 dont past the emission test


Definition of Diagnostic Trouble Code P1345 Audi: Ignition Coil Power Output Stage 3 Short to Ground BMW: Misfire Cylinder 2 with Fuel Cut-Off Buick: Crankshaft Position (CKP)-Camshaft Position (CMP) Correlation Cadillac: Crankshaft Position (CKP)-Camshaft Position (CMP) Correlation Chevrolet: Crankshaft Position (CKP)-Camshaft Position (CMP) Correlation Ford: Cylinder Discrimination Signal (Signal From Camshaft Position Sensor) GMC: Crankshaft Position (CKP)-Camshaft Position (CMP) Correlation Isuzu: Crankshaft Position - Camshaft Position Correlation Kia: No SGC Signal (1.6L) Lexus: Variable Valve Timing / CMP Sensor Range / Performance Lincoln: Cylinder Discrimination Signal (Signal From Camshaft Position Sensor) Mazda: Cylinder Discrimination Signal (from CMP sensor) Mercury: Cylinder Discrimination Signal (Signal From Camshaft Position Sensor) Oldsmobile: Crankshaft Position (CKP)-Camshaft Position (CMP) Correlation Pontiac: Crankshaft Position (CKP)-Camshaft Position (CMP) Correlation Saturn: Crankshaft Position (CKP)-Camshaft Position (CMP) Correlation Toyota: Variable Valve Timing / CMP Sensor Range / Performance Volkswagen: Ignition Coil Power Output Stage 3 Short to Ground

Jul 19, 2015 | GMC Cars & Trucks

2 Answers

Have a 2000 xterra code comes up p0340 says camshaft position sensor.when i go to the dealer they say it has no camshaft position sensor plz help


Hey Travis here is the compleat definition of code P0340=
NO CAM SIGNAL AT PCM , NO FUEL SYNC. YOU CAN TRY THE AUTOZONE LIBRARY FOR MORE INFO. there is more to it than sensor not being there. check the power control moudel.

Oct 24, 2014 | 2000 Nissan Xterra

2 Answers

Where is the camshaft position sensor for


They are located on each head if im not mistaken on the corner near the air intake boot that goes to air filter. The cylinder head close to the radiator is 2 4 6.

Sep 20, 2014 | 2000 Lexus ES 300

1 Answer

Camshaft position sensor


ON THE 4 CYLINER ENGINE CAMSHAFT SENSOR LOCATED AT THE LEFT DRIVERS SIDE OF THE TIMING COVER. THE V - 6 ENGINES CAMSHAFT POSITION SENSOR LOCATED AT THE FRONT OF ENGINE BLOCK BELOW THE POWER STEERING PUMP.

Aug 28, 2012 | 2000 Oldsmobile Bravada

1 Answer

Where is the camshaft position sensor located on 2000 jaguar s type 4.0


most cam position sensors are located in the distributor of an engine. if you have a direct ignition system then the sensor can be located on the cylinder head either front or back... your engine is the same as a ford 4.0 liter...

Jul 14, 2012 | 2000 Jaguar S-Type

2 Answers

I can't find the location of the crankshaft postion sensor in my 2000 Hyundai sonata


My online Sonata manual shows these possibilities, but does not identify which applies specifically to 2000 Sonata.
Also, when you talk to the dealership parts counter, you'll need to know whether your 2000 Sonata is (a) 4-cylinder 2.4L MFI DOHC engine, or (b) 6-cylinder 2.5L MFI DOHC engine.
Its easy to tell - just count your spark plug wires.

-- begine excerpt from 2000 Hyundai Sonata Repair guide --

The crankshaft position sensor is located next to the flywheel.
The crankshaft position sensor is located next to the flywheel/torque converter.
The camshaft position sensor is located on the engine near the timing belt cover and under the upper radiator hose.
The crankshaft position sensor is located on the driver-s side of the vehicle, down by the lower radiator hose.
The crankshaft position sensor is located on the engine near the crankshaft pulley.
The crankshaft position sensor is located at the front of the engine near the timing belt.

--- end excerpt from 2000 Hyundai Sonata repai guide ---

Dec 29, 2010 | 2000 Hyundai Sonata

1 Answer

How do you check and change a camshaft position


The camshaft sensor wouldn't explain the clattering noise. But a timing chain would explain both. Clattering from a loose chain and the camshaft sensor code from when the chain broke and the camshafts stopped turning.

Aug 02, 2010 | 2000 Chevrolet Tracker

1 Answer

Locating camshaft positioning sensor on 2000 Daewoo Laganza


hi,
it is under the upper timing belt cover between the camshaft gears. According to the manual touching anything related to timing belt requires removing million parts including right front wheel. I suspect this might be an overkill just to remove upper timing belt cover.

So my advice would be to get it done by some mechanic as u will not be able to do it and may damage other parts also.

Thanks!
Sandy

May 18, 2009 | 2000 Daewoo Lanos

2 Answers

Need help finding camshaft position sensor


2.0L 2.4L Removal The camshaft position sensor is mounted to the rear of the cylinder head.

Remove the negative battery cable. Disconnect the PCV hose and reposition Disconnect electrical connectors from the camshaft position sensor. Remove camshaft position sensor mounting screws. Remove sensor.Loosen screw attaching target magnet to rear of camshaft and remove magnet.
Instalation The target magnet has locating dowels that fit into machined locating holes in the end of the camshaft.
- Install target magnet in end of camshaft. Tighten mounting screw to 3 Nm (30 in. lbs.) torque. Over torqueing could cause cracks in magnet. If magnet cracks replace it.
- Install camshaft position sensor. Tighten sensor mounting screws to 12.9 Nm (115 in. lbs.) torque.
- Carefully attach electrical connector to camshaft position sensor. Installation at an angle may damage the sensor pins. - Connect the PCV Valve hose. - Connect the negative battery cable.
2.7L V6 Removal
The camshaft position sensor is mounted in the front of the head.

Disconnect electrical connector from sensor. Remove camshaft position sensor screw.
CAM Sensor Location 2.7L
Without pulling on the connector, pull the sensor out of the chain case cover.

Installation - Install sensor in the chain case cover and push sensor in until contact is made with the boss on the head. While holding the sensor in this position,install and tighten the retaining bolt to 12 Nm (105 in. lbs.) torque.
- Attach electrical connector to sensor.

Good luck and hope this helps





May 02, 2009 | Dodge Stratus Cars & Trucks

1 Answer

Locating camshaft positioning sensor on 2000 Daewoo Laganza


when you open your hood and you look on the valve cover you see on your left side of top of your cover a cable sticking out from a black piece that is the positioning sensor that cranksup the car

Mar 03, 2009 | 2000 Daewoo Lanos

Not finding what you are looking for?
2000 GMC Sonoma Extended Cab Logo

Related Topics:

234 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...