Question about 1995 Ford Mustang

1 Answer

Here is the timeline as to what happened to my '95 mustang gt. Maybe then someone can help by understanding the sequence of events. The battery was weak due to me leaving the lights on. I jumped it, and it started. I then charged the battery. Left the car parked for a day or so. When I tried to start, it was as if the battery was dead again. So I had the battery checked out. It checked good. So I troubleshooted and replaced the starter relay. Still won't start. I then replaced the solenoid, and still won't start. So I replaced the starter! And still won't start. It still sounds as if the power is not making contact to the starter when I turn the key....I am stumped. Help!

Posted by on

  • ccn7 May 11, 2010

    Chk. for fuseable links that might be burnt, like around starter, or around battery, If you find one just pull on it if its burnt it will pull apart. If that all chk. out ok(you did not say if its stick or automatic) it could be a park neutral switch or starter switch. also If its equiped with a switch on the clutch, where clutch has to be depressed to start.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 508 Answers

Even though you had the battery checked it may be bad or have a weak cell in it. It can be charged and then keep a surface charge on for a little bit and then die. To check a battery out you need to use a good carbon pile tester and not just one of the old fashioned load testers. I guarantee you that it is most likely the battery. Especially if the battery is 4 plus years old or more. Cold weather just kills batteries as does hot weather. Good luck.

Posted on Mar 05, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the fuse located for the alarm system on my 95 mustang gt ?


may be look in and around auxillary battery for alarm

Sep 27, 2014 | 1995 Ford Mustang GT

1 Answer

93 mustang dies no apparent reason


Not sure if you fixed your stall issues but....have you looked at the pip signal on your fox mustang? My 1987 mustang gt was doing the same thing it got to the point where the car failed to start. It was the pip sensor located in the distributor. I removed the distributor and took out the pip sensor replaced it with a oem replacement re-timed the car its ran great since. I also went to the boneyard and grabbed a few tfi and installed one on my distributor most mechanics suggest you do this when you replace the pip sensor. Hope this helps someone dealing with this issue on there 87-95 mustang gt. Took me about 45 minutes

Aug 03, 2013 | Cars & Trucks

2 Answers

I recently replaced my 96 mustang 3.8 with a 95 3.8 but now wont start is not getting spark. Do i need ecm out of a 95. It turns over fine but no spark any help...


No but you may need to put the sensers from the other motor on your new one. The most likly reason that it has no spark is youv'e yet to connect somthing. or in your haste to get it done you pinched some wires between the engine and the transmission ( common ) Look it over good and you may happen on the failure and as it's corrected you'l ( get-r-done)

Sep 16, 2010 | 1996 Ford Mustang

1 Answer

Putting a 302 in a 99 mustang


You'll need the K-member from a 94'-95' v6 or GT, along with the correct motor mounts. once you have that it should drop right in. But there are many more parts you'll need to make it work like a 5.0 tranny, exhaust, wiring, pcm, radiator, and maybe more. Look in the Ford Racing catalog and drop a 4.6L Cobra motor in there. A lot fewer parts to buy. Also if your state has car inspections the 5.0 is not OBDII, and should only be attempted if its going to be a "race only" car.

Jan 08, 2010 | 1999 Ford Mustang Cobra

1 Answer

Car fails to restart after intial drive


Sounds like TFI module I think 95 was the last year for it. Car runs great but when it gets hot dies out. TFI module.

Apr 22, 2009 | 1995 Ford Mustang

1 Answer

Where to find fuse diagram for 95 Ford Mustang?


http://www.allfordmustangs.com/forums/attachments/94-95-tech/608d1036338026-need-fuse-box-diagram-95-gt-esb01113.gif


hope that helps.

Mar 26, 2009 | 1995 Ford Mustang

3 Answers

Beeping noise - 2005 Mustang


You know, I have a 2005 Mustang GT that honks randomly. MAKE SURE you troubleshoot it now. I waited and now my alternator is fried. About 95% of voltage disturbances can be contributed to the alternator, and from what I understand the alternators on our cars are notorious for crapping out. -Amanda

Aug 01, 2008 | 2005 Ford Mustang

Not finding what you are looking for?
1995 Ford Mustang Logo

Related Topics:

99 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

63291 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...