Question about 2000 Pontiac Grand Am GT

1 Answer

2000 gt brak light on no brake fl. comes out from rear brakes new pads,

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,392 Answers

If it has disc brakes, you need new calipers. If it is drum brakes, you need new wheel cyliders.

Posted on Mar 06, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Light on dash for brakes and w/o, what does that mean


heck thebrake fluid level before you go any further ,

Dec 06, 2014 | Cars & Trucks

1 Answer

New breaks starting to sounds scrachy when they are applied


One word of advise. If your caliber bracket is hitting the rotor, or rubbing it. It may be a faulty or loose wheel bearing. Sometimes when the bearings are replaced in these cars they sometimes are pressed in a bit too far , and will cause the bracket to appear off set. Listen when turning corners for the rubbing to get louder or go away. I've replaced many Alero brakes, and 50% of the Aleros that come in have bad bearings. Brakes on these cars are known to wear very quickly as well. It's a heavy car and only standard braking. Then they decided to give them rear wheel disk brakes , but still very light for the weight of the car. Good luck Cheers from Nova Scotia

Jan 15, 2013 | 2000 Oldsmobile Alero

2 Answers

2000 olds bravada rear brakes are draging. changed brake hose's to calupers and the center hose as well. with new brake and rotors still draging not sure what to do next.


I also have this problem on my 2000 Bravada - replaced all rotors and back calipers, brand new brake pads, new system and my rear caliper STILL chewed up a brand new brake pad in one week down to the metal. Checking for an emergency brake issue at this point - if anyone has any suggestions about how to unhook the E Brake, please share!

Jan 13, 2010 | 2000 Oldsmobile Bravada

2 Answers

Turn signal is staying on continuously and brake light goes off


check the bulbs or the sockets for damage
or the wrong bulb
you are getting feedback through the wiring
and that lights up the dash

Jan 10, 2010 | 2000 Toyota Tacoma PreRunner

2 Answers

I HAVE A 1999 PONTIAC GRAND PRIX AND THE BRAKE LIGHT COMES ON SOMETIMES IS THIS JUST A SENSOR OR IS IT A PROBLEM WITH THE BRAKES?


it should be the switch that gives electricity to your lights, its probabbly not a brak problem but a electrical problem
hope this helps

Nov 18, 2009 | 1999 Pontiac Grand Prix

1 Answer

I'm fitting new braks pads to the rear. How do I


with the help of another person, you have to pull the spring back with one person and attach it yourself

Jun 17, 2009 | 1998 Ford Explorer

2 Answers

Rear caliper piston how to get it to move back inorder to change pads


take a c clamp put one of your old brake pads over the piston and tighten the clamp until piston goes back the whole way

May 23, 2009 | 2006 Pontiac G6

2 Answers

Dash Board Brake Light comes on


brake light switch near brake pedal sticking

Apr 20, 2009 | 2000 Nissan Maxima

2 Answers

Breaks sticking...


Sounds like your master cyllinder has died.

Mar 30, 2009 | 1994 Toyota Pickup

2 Answers

Here is a Problem for you all! 2000 Grand Am GT ram air v6 ABS and Brake light always on, No trouble codes, and no rear brakes at all key on or off. Has fluid at M/C and to ABS unit but not from unit to...


This problem sounds like and ABS module that has gone bad, the ABS module has toothed gears inside that actuate the ABS motor, if one of these gears slips a tooth or "unwinds" itself if will not circulate brake fluid to where it needs to go (ex: the rear brakes) alot of times the brake and ABS light will come on, but will not set any trouble codes. My recommendation is to take this to a repair shop and have them verify the problem and replace the ABS module, the motor gears have to be properly aligned when replacing or the lights will stay on and you will still have the same problem. Hope this helps.

Mar 10, 2009 | 2000 Pontiac Grand Am GT

Not finding what you are looking for?
2000 Pontiac Grand Am GT Logo

Related Topics:

44 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...