Question about 1997 Toyota Previa

1 Answer

How do i remove front brake discs on my Lucida 4x4

How do i remove front brake discs on my Toyota Lucida 4x4 please

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 150 Answers

Remove the front wheels. Remove the brake calipers (usually held with two stud bolts on the stub axle assembly.(look behind the disc)The discs should then pull off. On reassmbly ensure the caliper bolts are fully tightened.

Posted on Mar 07, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1989 toyota pickup front disk brake pads replaced, now the front calipers wont clear the new disk brake pads! Any solutions, please?


remove caliper, push disc all way home, put wheel nut on to hold home, retry fitting them the disc may be slightly scued. If no go try diffrent brand of pad I had same prob with a diffrent car last week & diffrent brand pad was 2mm thiner. If can't exchange pads get piece of emery paper on flat surface & sand away top part of pad material in round motions both ways till they fit. :-)

Jul 09, 2012 | Toyota Cars & Trucks

1 Answer

How do I replace "front brakes" toyota corolla


Replacing front disc brakes is a relatively easy task. The attached link will walk you through the steps:

http://www.ehow.com/how_4520110_replace-front-disc-brakes-toyota.html

Please remeber to rate this solution. Thanks!

Feb 05, 2011 | 2006 Toyota Corolla

1 Answer

Front disc brake rotors on Toyota T100 4wd


Remove the calipers like on any other vehicle. You will have to remove the hubs as the rotors are attached to them. It's more involved that a standard passenger vehcle.

Apr 19, 2010 | 1998 Toyota T100

1 Answer

How do you replace the front brake caliber on a 1997 ford expedition


Caliper Removal
  1. svj~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not use heat to loosen a seized lug nut . Heat can damage the wheel and the wheel bearings.
    Loosen the lug nuts.
    1. Remove the center cap.
    1. With the weight of the vehicle on the wheels, loosen the lug nuts.
      1. svj~us~en~file=ani_caut.gif~gen~ref.gif WARNING: THE ELECTRICAL POWER TO THE AIR SUSPENSION SYSTEM MUST BE SHUT OFF PRIOR TO HOISTING, JACKING OR TOWING AN AIR SUSPENSION VEHICLE. THIS CAN BE ACCOMPLISHED BY TURNING OFF THE AIR SUSPENSION SWITCH LOCATED IN THE RH KICK PANEL AREA. FAILURE TO DO SO MAY RESULT IN UNEXPECTED INFLATION OR DEFLATION OF THE AIR SPRINGS WHICH MAY RESULT IN SHIFTING OF THE VEHICLE DURING THESE OPERATIONS.
        Raise and support the vehicle.
      1. Remove the wheel and tire assembly.
        1. Remove the lug nuts.
        1. Remove the wheel and tire assembly.
      2. CAUTION: Replace the lining if worn to or past specifications. Replace the brake shoes and linings in complete axle sets. Inspect the brake shoes and linings for wear or contamination.
      3. svj~us~en~file=ani_caut.gif~gen~ref.gif WARNING: BRAKE FLUID CONTAINS POLYGLYCOL ETHERS AND POLYGLYCOLS. AVOID CONTACT WITH EYES. WASH HANDS THOROUGHLY AFTER HANDLING. IF BRAKE FLUID CONTACTS EYES, FLUSH EYES WITH RUNNING WATER FOR 15 MINUTES. GET MEDICAL ATTENTION IF IRRITATION PERSISTS. IF TAKEN INTERNALLY, DRINK WATER AND INDUCE VOMITING. GET MEDICAL ATTENTION IMMEDIATELY.
        Disconnect the front brake hose (2078).
        1. Remove the front brake hose bolt.
        1. Remove the copper washers. Plug the front brake hose.
        1. Disconnect the front brake hose
      4. Remove the disc brake caliper (2B120).
        1. Remove the two caliper bolts.
        1. Lift the front disc brake caliper (2B121) off the front disc brake caliper anchor plate.
      5. On 4x2 vehicles, measure the front disc brake hub and rotor (1102) thickness.
        • Replace the front disc brake hub and rotor if not within specifications 27.7mm Min.
      6. On 4x4 vehicles, measure the front disc brake rotor thickness.
        • Replace thhe front disc brake rotor if not within specifications. 27.7mm Min.
      7. Inspect the disc brake caliper for leaks.
        • If leaks are found, disassembly is required

Mar 10, 2010 | 1997 Ford Expedition

1 Answer

How do you get the rear brake rotor off, normally they just pull off once the caliper is removed, I did'nt want to beat on it.


Removal & Installation
  1. Remove the front wheel.
  2. Drain the brake fluid.
  3. Remove the union bolt and gasket from the disc brake cylinder and disconnect the flexible hose.
  4. Remove the disc brake cylinder sub-assembly.
  5. Remove the disc brake pad kit.
  6. Remove the two disc brake pad support plates from the cylinder mounting.
  7. Remove the two cylinder slide pins from the disc brake cylinder mounting.
  8. Remove the two bolts and the disc brake cylinder mounting.
  9. Remove the disc.
  10. Immediately, matchmark the disc to the axle hub.
To install:
  1. Installation is the reverse of removal.
  2. Torque the disc retaining bolts to 76 ft. lbs. (103 Nm).

Jan 18, 2010 | 2002 Toyota Camry

1 Answer

How do you install a DISC BRAKE HARDWARE KIT in 1980 toyota pickup ''front disc brake''


remove all connection bolts , clips. I then slowly pry the brakes as far from the rotor as posible ( depressing the brake cylinder) with tire tool or large screw driver, so the new thicker pads will go in with ease. Replace new pads acording to toyota and replace bolts/ clips. this method requires no bleeding of brakes.

Oct 22, 2009 | 1983 Toyota Pickup

2 Answers

Gear lever stuck on '96 Toyota Lucida Estima


Automati Estimas have a safety device that locks the gear lever in 'park' until the brake pedal is pressed. Turn on the ignition and check that the brake lights are working, as the lock works on the same circuit. There may be a problem with the wiring to the lock mechanism

Apr 24, 2009 | Toyota Passenger Cars & Trucks

Not finding what you are looking for?
1997 Toyota Previa Logo

Related Topics:

248 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...