Question about 2004 GMC Sierra 2500

Open Question

Looking for manual for programing an ungo clarion car starter for 2004 gm truck number on back of starter is FCC ID-EZSDEI474V

Posted by on

3 Suggested Answers

  • 59 Answers

SOURCE: programming a remote

i would take it to a dealer and have them program it for you it should not cost to much

Posted on Jan 02, 2009

  • 1 Answer

SOURCE: 2004 gmc sierra truck

UNLESS YOU ARE WITH A FAMILIAR WITH NEWER AUTOMOTIVE ELECTRONICS, I WOULD ADVISE AGAINST DOING AN AFTERMARKET ALARM / KEYLESS SYSTEM YOURSELF. THE PASS KEY CODES YOU ARE TRYING TO GET WOULD REQUIRE A DEDICATED MANUFACTURER SCAN / DIAGNOSTIC TOOL TO GAIN THE NUMBERS FROM THE BODY CONTROL MODULE. THE LEADING SNAP-ON SCAN TOOL STILL WILL NOT GET THE INFORMATION YOU NEED.
YOU MAY BE ABLE TO CONTACT YOUR LOCAL VEHICLE DEALERSHIP AND SEE IF THEY CAN GET YOU THE NUMBERS YOU REQUIRE FROM YOUR VEHICLE IDENTIFICATION NUMBER OR "VIN" NUMBER FROM THE VEHICLE.
AS FOR THE KEYLESS SYSTEMS AVAILABLE IN THE AFTERMARKET SCENE ANY SYSTEM WOULD REQUIRE A DEDICATED PASS KEY ENABLER PURCHASED AT AN ADDITIONAL CHARGE FOR MOST 2002 AND UP DOMESTIC VEHICLES.
BEST THING TO DO IS INQUIRE WITH THE MANUFACTURER OF THE VEHICLE AT A LOCAL DEALERSHIP IN YOUR AREA AND SEE IF YOU CAN PURCHASE JUST THE ''KEY FOB'' FOR A REASONABLE PRICE VERSUS THE EXPENSE OF EVERYTHING ELSE. THE VEHICLE MAY EVEN BE EQUIPED WITH FACTORY REMOTE START OPTION.

JUST AN FYI ALSO, IF THE VEHICLE WAS PURCHASE USED IT MAY BE MISSING THE KEY FOBS BECAUSE THE VEHICLE WAS A REPOSESED ITEM, I HAVE SEEN THIS A FEW TIMES BECAUSE MOST LENDING INSTITUTIONS ONLY HOLD ONTO THE KEYS AND GIVE ORIGINAL AND EXTRA KEYS AND FOBS TO THE PARTY WHO PURCHASED THE VEHICLE NEW.

Posted on Jan 09, 2009

Molson02536
  • 3854 Answers

SOURCE: need help programing my keyless remote for a 2000

1. Close the vehicle doors.

2. Turn ignition to the ON position then OFF.

3. Remove key from the ignition.

4. Press and hold the driver side door lock switch in the UNLOCK position
until step 8.

5. Insert the ignition key into the ignition lock cylinder and remove the key.
(Do not turn the ignition key in the lock cylinder)

6. Insert the ignition key into the ignition lock cylinder and remove the key.
(Do not turn the ignition key in the lock cylinder)

7. Insert the ignition key into the ignition lock cylinder.
(Do not turn the ignition key in the lock cylinder)
Leave key in the ignition cylinder.

8. Release the door lock switch. The vehicle will sound three beeps in order
to verify the Program Mode has been activated.

9. Press the LOCK and UNLOCK buttons together on the keyless remote and
hold unitl the vehicle beeps twice to verify that the keyless remote has been
successfully programmed. This may take approximately 15 seconds.

10. Perform the previous step (9) to program up to four keyless remotesm, including
any old ones.

11. Remove the ignition key to exit Program Mode.



Thank you for using Fixya and good luck

Posted on Mar 17, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need a owner manual


You can download the owners manual for free at the GM owners site below. You need a Yahoo ID to use the site, that is also free to sign up for. Follow the link please.

http://www.gm.com/gmownercenter/gm/

Oct 05, 2011 | 2004 Chevrolet Malibu Maxx

1 Answer

Looking for a FREE owner's manuals for a 1998 Chevy 3500 6.5 L diesel truck and a 2004 Ford F250 power stroke diesel truck


For 1993-current models, must have a Yahoo ID to log in. Try it: gm.com/gmownercenter

Hope helps (remember to rate this answer).

Dec 15, 2010 | Chevrolet 3500 Cars & Trucks

1 Answer

Programming keyless entry key fob for 2000 chevy


you need to call the nearest chevy dealer with you vin, and get the part number from them, there are 2 numbers on the back of the remote, see if they match what the dealer tells you. Have an automotive locksmith program, should cost about 75.00 to do.

Jan 27, 2010 | 2000 Chevrolet Malibu

1 Answer

03 chevy monte carlo radio programming


WOW I think someone is very confused here.
The key fob & radio do not have anything in common. The first thing I would do is go to your local Chevy dealership parts department and give them the complete vehicle identification number. He can look up your vehicle to see if GM build you car with GM factory keyless entry system. If GM buiilt you car with keyless entry you'll need to have the service department program the key fob to the car. (This is not done through the radio, I've work for GM for 30 years, this is not how they built it)
If your radio needs to programed, that is done through the radio. 2 seperate circuits.
Maybe you should look at going to another Chevy store, I don't think the first one the advisor new what he was talking about.

Jul 08, 2009 | 2004 Chevrolet Impala

1 Answer

F150 keyless entry not working.Checked battery in keypad, check ok.The door lock buttons in the truck work. I checked all fuses and relays. I'm stumped would appreciate any help.


go to autozone--you can test remote there-if u need a new one they will take fcc id numbers off the back and order new one- comes with instructions to program it--the one 4 my explorer cost 58 dollars they can be higher than that

Mar 05, 2009 | Mitsubishi Galant Cars & Trucks

1 Answer

Programming a remote


i would take it to a dealer and have them program it for you it should not cost to much

Jan 02, 2009 | 2000 Cadillac Escalade

1 Answer

Key Fob Programming


key fobs have to be the same gm id number on back of fob and need to be programmed for your car by the dealer. its expensive . i had to have it done on my car. other fob i had could not be programmed to work, wrong gm id number

Nov 25, 2008 | 2005 Pontiac G6

1 Answer

Keyless remote programming insyructions


If the remote is generic you will need the factory remote to "clone" the signal to the new remote.

With your oem pontiac remote you may need to visit any GM service center to have the remote set to the cars receiver. There are literally 100,000 different variables GM uses to ensure one remote can't work the wrong car. A typical key programming will run you between $30-$60 depending on how much greed the technician has. Some good technicians will do this job for free simply to make a customer happy so you may wish to call around.

Jun 29, 2008 | 2000 Toyota Corolla

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

188 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

70346 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...