Question about Mitsubishi Galant

1 Answer

F150 keyless entry not working.Checked battery in keypad, check ok.The door lock buttons in the truck work. I checked all fuses and relays. I'm stumped would appreciate any help.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 18 Answers

Go to autozone--you can test remote there-if u need a new one they will take fcc id numbers off the back and order new one- comes with instructions to program it--the one 4 my explorer cost 58 dollars they can be higher than that

Posted on Mar 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Crown vic trunk release doesn't work


Do you know if your door locks are module controlled or non module controlled ?
Locks, Latches and Entry Systems - Module Controlled
Principles Of Operation
s5a~tr~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not use a key, pencil or any other hard object to press the keyless entry keypad buttons. These objects may damage the keyless entry keypad buttons.
NOTE: The remote transmitter will not operate with the transmission in REVERSE or DRIVE.
NOTE: Upon installation of a new driver door module (DDM), the module must be reconfigured. Refer to Section 418-01 .
The DDM receives inputs from the digital transmission range (TR) sensor, ignition switch, brake switch, door lock control switches, lighting control module (LCM), keyless entry keypad and remote transmitter. The DDM outputs consists of keyless entry keypad illumination, door lock actuators, luggage compartment lid release solenoid, and LCM.
For DDM removal and installation information, refer to Section 419-10 .
Inspection and Verification
s5a~tr~en~file=ani_caut.gif~gen~ref.gif WARNING: If equipped with fire suppression system, refer to Section 419-03 for important safety warnings.
NOTE: Before starting electrical diagnosis, check for mechanical binds by manually operating the door locks. Operate lock system several times from each switch while observing the operation of all door locks. Be sure battery is fully charged.
  1. Verify the customer concern.
  1. Visually inspect for obvious signs of mechanical and electrical damage.
  2. Visual Inspection Chart Mechanical Electrical
    • Binding latches
    • Battery junction box (BJB) fuse 8 (20A)
    • Central junction box (CJB) fuse(s):
      • 10 (5A)
      • 18 (10A)
      • 25 (10A)
    • Circuitry
    • Connectors
    • Door lock actuator
    • Door lock control switch
    • Keyless entry keypad
    • Luggage compartment lid release switch
    • Luggage compartment lid release solenoid

    1. If an obvious cause for an observed or reported concern is found, correct the cause (if possible) before proceeding to the next step.
    1. If the cause is not visually evident, connect the diagnostic tool to the data link connector and select the vehicle to be tested from the diagnostic tool menu. If the diagnostic tool does not communicate with the vehicle:
      • check that the program card is correctly installed.
      • check the connections to the vehicle.
      • check the ignition switch position.
    1. If the diagnostic tool still does not communicate with the vehicle, refer to the diagnostic tool operating manual.
    1. Carry out the diagnostic tool data link test. If diagnostic tool responds with:
      • SCP or ISO circuit fault; all electronic control units no response/not equipped, refer to Section 419-10 .
      • No response/not equipped for the DDM, refer to Section 419-10 .
      • No response/not equipped for the LCM, refer to Section 419-10 .
      • System passed, retrieve and record the continuous diagnostic trouble codes (DTCs), erase the continuous DTCs and carry out self-test diagnostics for the DDM and LCM.
    1. If the DTCs retrieved are related to the concern, go to the Driver Door Module (DDM) Diagnostic Trouble Code (DTC) Index or Lighting Control Module (LCM) Diagnostic Trouble Code (DTC) Index to continue diagnostics.
    1. If no DTCs related to the concern are retrieved, GO to Symptom Chart .
    Drive Door Module (DDM) Diagnostic Trouble Code (DTC) Index DTC Description Source Action B1352 Ignition Key In Circuit Failure DDM Go To Pinpoint Test H . B1396 Door Lock Circuit Short To Battery DDM Go To Pinpoint Test C . B1526 Keyless Entry Keypad Circuit Short To Ground DDM Go To Pinpoint Test E . B1553 Luggage Compartment Lid Release Circuit Short To Ground DDM Go To Pinpoint Test B . B1751 Park/Neutral Switch Circuit Short To Battery DDM Go To Pinpoint Test L . B2425 Remote Keyless Entry Out Of Synchronization DDM Go To Pinpoint Test M .
    Lighting Control Module (LCM) Diagnostic Trouble Code (DTC) Index
    DTC Description Source Action B1300 Door Lock Circuit Failure LCM Go To Pinpoint Test N . B1310 Door Unlock Circuit Failure LCM Go To Pinpoint Test N . B1396 Door Lock Circuit Short To Battery LCM Go To Pinpoint Test N . B1397 Door Unlock Circuit Short To Battery LCM Go To Pinpoint Test N . B1677 Alarm Panic Input Circuit Failure LCM Go To Pinpoint Test J . B1679 Alarm Panic Input Circuit Short To Battery LCM Go To Pinpoint Test J .
    NOTE: For a complete list of DDM and LCM DTCs, refer to Section 419-10 .
  3. ????????????? Do you have a professional scan tool ?
    ??

Sep 17, 2016 | 2005 Ford Crown Victoria

1 Answer

Keyless remotes not working


Try reprogramming the remotes. Here are the instructions for the procedure. Hope it helps. Cobra!
Programming NOTE: All keyless entry remote transmitters (15K601) must be programmed at the same time.
NOTE: To program (or reprogram) the keyless entry remote transmitters into the RAP module, perform the following steps:
  1. Make sure that the anti-theft system is not armed or triggered.
  1. Turn the ignition switch (11572) from OFF to RUN eight times within ten seconds, ending in RUN. If the RAP module has successfully entered program mode, it will lock and then unlock all doors.
  1. Within 20 seconds, press any button on a keyless entry remote transmitter, and the doors will lock and then unlock to confirm that each keyless entry remote transmitter has been programmed. Repeat this step for each transmitter.
  1. If the door locks do not respond for any keyless entry remote transmitter, wait several seconds and press the button again. If the door locks still fail to respond, refer to Inspection and Verification.
  1. Turn the ignition switch to the OFF position, or wait up to 20 seconds after step 2, to exit program mode. If a keyless entry remote transmitter has been programmed (or reprogrammed), the RAP module will lock and unlock all doors one last time to confirm.

Jun 06, 2010 | 1998 Ford F150 Regular Cab

1 Answer

Keypad door lock does not work..?


it's in owner manual. But, first you have to enter your original code and it must work. then you press the 1 button and then enter a new 5 digit code, then press the 1 button again.

Keyless Entry Keypad To unlock the driver front door (20124) , and disarm the anti-theft alarm control (19A366) , (if equipped):
  • Enter the permanent factory code.
  • Enter the owner's alternate code.
To unlock the passenger door(s), press the 3/4 button within five seconds of unlocking the driver door or luggage compartment. To unlock the luggage compartment door (40110), press the 5/6 button within five seconds of unlocking driver or passenger door(s). To turn on the courtesy lamps and light all illuminated components, lift either front door handle (22404) or press any button on the keyless entry keypad (14A626) . To lock all doors, press the 7/8 and 9/0 buttons at the same time with all doors closed. (It is not necessary to enter the key code first.) This will turn off courtesy lamps and arm anti-theft alarm control (if equipped). To program an alternate code:
  1. Enter the five digit permanent entry code into keyless entry keypad .
  1. Within five seconds of pressing last button of permanent code, press the 1/2 button within five seconds of pressing the last button of the permanent code.
  1. Enter any alternate five digit code within five seconds of pressing 1/2 button.
    • Enter a sixth digit as follows to indicate operator's memory seat setting to be set by alternate code:
      • 9/0 — no memory recall
      • 1/2 — memory seat position 1
      • 3/4 — memory seat position 2
      • 5/6 — memory seat position 3
    • After successful programming, the doors will signal by locking and then unlocking.
---------------------------------------------
  • Keyless Entry Keypad Does Not Work Properly
  • Circuit.
  • Keyless entry keypad.
  • Electronic door lock control processor.

  • Open Fuses:
    • Town Car and Crown Victoria/Grand Marquis
    • Power Distribution Box (under hood)- K, 40A (Maxi)
    • Instrument Panel Fuse Panel - 17 (10A), 10 (20A), 8 (15A), 5 (15A) and 4 (10A)
  • Loose Connectors
  • Corroded Connectors
  • Oct 04, 2009 | 1995 Lincoln Town Car

    1 Answer

    Keyless entry on honda civic 2006 not working


    The keyless entry is designed to work with the doors closed (closed - not locked). If the door ajar sensor thinks the door is open the keyless entry is disabled. When you manually lock the door it might tighten the door just enough to activate the keyless entry. I would try slamming all the doors closed and then see if the keyless entry works. If it still wont work have the wiring checked on the front door lock.

    May 12, 2009 | 2006 Honda Civic Hybrid

    1 Answer

    Key Pad Entry does not work


    does the key pad light when you press a button at night? If yes, the fuse is ok.
    Do you have the plastic card with the permanent code in your owner manual packet? If yes, tryit.
    report back.

    Keyless Entry The keyless entry keypad is hardwired to the GEM. The GEM interprets the inputs from the keyless entry keypad and then controls the associated operation. The keyless entry keypad will be illuminated for five seconds when any button is pressed. Additionally, it will request the illuminated entry feature to turn the courtesy lamps on. If a lock all doors code is entered, the illumination will turn off, as well as request the illuminated entry feature to turn off the courtesy lamps. When pressed, the keyless entry keypad supplies the ground signal to the GEM or the GEM receives a signal from the keyless entry remote transmitter. Then the GEM outputs a ground signal to the appropriate lock or unlock relay which supplies the power to the actuator to lock or unlocks all doors, including the luggage compartment. The keyless entry remote transmitter also unlocks the liftgate or activates the panic alarm by sending a signal to the GEM.
    --------------------------------------------------------------- Visual Inspection Chart Mechanical Electrical
    • Keyless entry keypad
    • Keyless entry remote transmitter
    • Central junction box (CJB) Fuse F222 (20A)
    • Circuitry
    • Generic electronic module (GEM)
    ------------------------------------------------------------------------
    • No communication with generic electronic module (GEM)
    • Generic electronic module.
    • Circuitry.
    • REFER to Section 419-10 .
    ------------------------------------------------------------------------------------

    Mar 08, 2009 | 2003 Ford Taurus

    1 Answer

    2005 F150 Keyless Entry


    There is a technical service bulletin out on this probelm on 2004/2005 F150.
    ISSUE: Some 2004-2005 F-150 vehicles built through 2/7/2005, may exhibit an inoperative keyless entry keypad. This may be due to the vehicle security module (VSM) not being configured to accept keyless entry keypad input.

    The fix is to reprogam the vehicle security module with as-built data. So it would have to go to the dealer to do this.
    The tsb number is 05-5-5.

    Feb 21, 2009 | 2005 Ford F-150

    1 Answer

    There is no sound from the horn when I press on the horn in the steering column or when I hit the panic button on the keyless entry remote. I have checked the fuse and it is good, also have checked the...


    my keyless entry has been working great we went on vacation. it quit working i cheched the fuses and the battery in the remote everything is fine just does not work anymore

    Jul 22, 2008 | 2005 Ford Escape

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    236 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Mitsubishi Experts

    yadayada
    yadayada

    Level 3 Expert

    61037 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    21949 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    6812 Answers

    Are you a Mitsubishi Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...