Question about 2000 Hyundai Accent

1 Answer

Fuel pump Where is the fuel pump?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 362 Answers

In the gas tank.

Posted on Mar 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2006 for 500 it flooded out here in Houston and I do not want to use the gas that is in my tank how do I remove that gas without having to take it to a auto mechanic


syphon all the fuel out from the filler cap if possible
or the fuel pump fitting hole (under read seat )
pump will need to be cleaned and filter replaced any way
metho/clean fuel to evaporate all the water and clean out the tank

source online internet search
Fuel Pump Module
Item Part Number Description 1 9C335A Fuel pump module access cover 2 - Fuel vapor control tube assembly valve-to-fuel pump module quick connect coupling (part of 9C047) 3 - Rear fuel supply tube-to-fuel pump module quick connect coupling (part of 9G700) 4 14A464 Fuel pump module electrical connector 5 9C385 Fuel pump module lock ring 6 9H307 Fuel pump module 7 9276 Fuel pump module O-ring seal 8 - Fuel crossover tube-to-fuel pump module quick connect coupling (part of 9P860) 9 - Fuel crossover tube-to-fuel pump module quick connect coupling (part of 9P860) With vehicle in NEUTRAL, position it on a hoist.
Release the fuel system pressure.
Disconnect the battery ground cable.
Release the fuel tank filler cap and position aside.
Insert a suitable fuel drain tube into the fuel tank filler pipe until it reaches the fuel tank inlet spout
  • NOTE: When the fuel tank is completely full, this step will remove approximately 1/8 of fuel from the fuel tank.Attach the fuel storage tanker to the fuel drain tube and remove any residual fuel in the fuel tank filler pipe.
  • Release the fuel tank filler pipe hose clamp.
    • To install, tighten to 3 Nm (27 lb-in).
    Disconnect the fuel tank filler pipe hose from the fuel tank.
    Insert a suitable fuel drain tube into the fuel tank inlet spout
    1. NOTE: When draining a completely full fuel tank, this step will drain most of the fuel from the RH side of the fuel tank, and partially drain the LH side of the fuel tank due to the siphoning effect from the fuel crossover tube.Attach the fuel storage tanker to the fuel drain tube and drain the fuel from the RH side of the fuel tank.
    Five Hundred, Montego Remove the rear lower seat cushion.
    Release the latches and pull upward on the rear lower seat cushion and remove
    All vehicles
    Position the rear floor carpet and any padding or insulation covering the fuel pump module access cover aside.
    Remove the fuel pump module access cover.
    Clean the surrounding area of the fuel pump module mounting flange and the quick connect couplings with compressed air.
    Disconnect the fuel pump module electrical connector.: Place absorbant pads in the general work area in case of fuel spillage.
    Disconnect the rear fuel supply tube-to-fuel pump module quick connect coupling.
    Disconnect the fuel vapor control tube assembly valve-to-fuel pump module quick connect coupling.
    Install the special tool and remove the fuel pump module lock ring.
    Carefully lift the fuel pump module out of the fuel tank allowing access to disconnect the crossover tube quick connect couplings.
    Disconnect the crossover tube-to-fuel pump module quick connect couplings
    Completely remove the fuel pump module from the fuel tank.
    NOTE: To install, apply clean engine oil to the O-ring seal.
    Remove the fuel pump module O-ring seal.
    To install, reverse the removal procedure.
    • Make sure the alignment arrows on the fuel pump module and the fuel tank meet before tightening the fuel pump module lock ring.
    • Tighten the fuel pump lock ring until it meets the stop tabs on the fuel tank.
    • thanks









    26183499-wiv2epenzjiy1tbpzyhd3fmz-1-0.gif

    May 03, 2016 | Cars & Trucks

    2 Answers

    How do I change the fuel pump in a 2009 GMC Acadia


    drop the fuel tank and remove the circle lock. Youll see it when you take the cover off.

    Feb 03, 2015 | GMC Cars & Trucks

    2 Answers

    No fuel coming to carburator


    It could be fuel pump or fuel pump relay.Click here to see how to remove fuel pump.Click here to see fuel pump.See how much the fuel pump is,make sure it's that.Here's the fuel pump relay.Here's how to remove fuel pressure.

    Dec 23, 2012 | 2003 Saturn VUE

    2 Answers

    Where is fuel pump for 1996 mercury mystique located on the car and how do you remove it


    SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Multi-Port Fuel Injection (MFI) Fuel Pressure Gauge T80L-9974-B
    Removal
    1. Depressurize fuel system as outlined in Service Procedures- Fuel System Pressure Relief.
    1. Remove rear seat cushion. Refer to Section 01-10.
    1. Remove plastic grommet from floor pan.
    1. Disconnect fuel pump module electrical connector.
    1. NOTE: To disconnect fuel tubes from fuel pump module, compress tabs on both sides of each nylon push connect fitting and ease fuel tube out of fuel pump module.

      Disconnect fuel and vapor return tubes from fuel pump module.
    1. Turn fuel pump locking retainer ring counterclockwise using Fuel Tank Sender Wrench D84P-9275-A or equivalent and remove fuel pump locking retainer ring.
    1. NOTE: After fuel pump module removal, immediately cover fuel pump module opening in fuel tank in order to prevent fuel system contamination.

      Remove fuel pump module and cover fuel pump module opening in fuel tank.
    1. Remove fuel pump module O-ring seal and discard.
    Installation
    1. NOTE: When cleaning fuel pump module mounting surface on fuel tank, use caution to prevent any foreign material from entering fuel system.

      Clean fuel pump module mounting flange and fuel pump module mounting surface and O-ring seal groove on fuel tank.
    1. Apply a light coat of Premium Long-Life Grease XG-1-C, -K or equivalent meeting Ford specification ESA-M1C75-B on a new O-ring seal to hold it in place and install it into the O-ring seal groove on the fuel tank.
    1. Install fuel pump module carefully to ensure that filter is not damaged. Make sure that locating keys are in keyways and O-ring seal remains in place.
    1. Hold fuel pump module in place and install fuel pump locking retainer ring finger-tight. Make sure that all locking tabs are under fuel tank lock ring tabs.
    1. Secure fuel pump locking retainer ring by rotating clockwise using Fuel Tank Sender Wrench D84P-9275-A or equivalent until fuel pump locking retainer ring rests against stops.
    1. Connect fuel and vapor return tubes to fuel pump module.
    1. Connect fuel pump module electrical connector.
    1. Install plastic grommet in floor pan.
    1. Install rear seat cushion. Refer to Section 01-10.
    1. Install Multi-Port Fuel Injection (MFI) Fuel Pressure Gauge T80L-9974-B as outlined in Service Procedures-Fuel System Pressure Relief.
    1. Turn ignition switch to RUN position for three seconds repeatedly (5 to 10 times) until pressure gauge reads at least 270 kPa (30 psi). Check for leaks at fittings.
    1. Remove pressure gauge, start engine and recheck for leaks.
    Hope this helps

    Aug 13, 2011 | 1996 Mercury Mystique

    1 Answer

    I need to replace the fuel pump on my 2001 Saturn L200 with a 2.2 L Engine. What is the best procedure?


    Fuel Pump REMOVAL & INSTALLATION 1.9L Engine To prevent excessive fuel spillage, whenever the tank is removed from the vehicle it should be no more than 1?2 full. Removal of the fuel pump module assembly requires the removal of the fuel tank.
    1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
    2. Properly relieve the fuel system pressure.
    3. Remove or disconnect the following:
      • Negative battery cable
      • Fuel feed and return lines from the filter/pressure regulator
      • Fuel pump vapor line from the fuel tank vent pipe
      • Fuel pump module retaining ring with service tool SA9156E. A 1?2 inch breaker bar will loosen the lockring
      NOTE: To prevent bending of the sending unit float arm, lift the pump module up slightly to disengage the orientation tabs in the tank. Rotate the module 90 degrees clockwise until the fuel lines are facing the 1 o'clock position.
      • Fuel pump module from the fuel tank until the bottom of the pump module is close to the fuel tank opening
      • Tilt the pump module approximately 45 degrees to the right hand side of the tank and lift the pump from the fuel tank
      • Fuel pump to tank seal and discard it
      To install:
    4. Install or connect the following:
      • Fuel pump module into the fuel tank by orientating the float to face the right side and tilting the module approximately 45 degrees
      • Fuel pump into the tank and rotate the assembly 90 degrees counterclockwise to align the module tabs with the slots in the tank
      NOTE: The fuel pump retaining ring cannot be properly installed if the flange locator tabs are not aligned with the slots in the fuel tank.
      • Retaining lockring with tool SA9156E
      • Vapor line to the fuel tank vent pipe
      • Fuel feed and return lines to the filter/pressure regulator
      • Fuel feed, return and EVAP canister purge line in the fuel tank retaining clip
      • Fuel tank
      • Negative battery cable
    5. Start the vehicle and check for leaks, repair if necessary.
    2.2L and 3.0L Engines
    1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
    2. Properly relieve the fuel system pressure.
    3. Remove or disconnect the following:
      • Negative battery cable
      • Fuel tank
      • Fuel lines from the fuel pump module cover
      • Fuel pump module retaining ring with a Sending Unit Wrench, J43827
      • Pull the retaining clip toward the float arm and lift up
      • Fuel pump straight up from the fuel tank
      • Fuel pump tank seal and discard the seal
      • Fuel feed line from the bottom of the fuel pump cover with Clamp Pliers J43914
      • Fuel pump electrical connector Fig. 1: Remove the fuel pump cover lockring-2.2L and 3.0L engines 9306zg57.gif
      To install:
    4. Install or connect the following:
      • Fuel pump feed line to the cover
      • Fuel pump electrical connector
      • Fuel pump to the new seal
      • Fuel pump cover lockring with tool J-43827
      • Fuel lines and wiring harness
      • Fuel tank
      • Negative battery cable
    5. Start the vehicle and check for leaks, repair if necessary.
    prev.gif next.gif

    Jan 29, 2011 | 2001 Saturn L-Series

    1 Answer

    Does my 2000 ford expidition have a little compartment to replace my fuel pump.


    Fuel Pump Module-in tank, no compartment to replace fuel pump Removal & Installation To Remove:
    WARNING
    Highly flammable mixtures are always present in any fuel related component. Smoking or carrying lighted tobacco or an open flame of any type may ignite the flammable mixtures.
    WARNING
    Even when the engine is not running, fuel in the fuel system remains under high pressure. Fuel system pressure must be relieved before working on or disconnecting any of the fuel lines, fuel tubes, or fuel system components. Failure to do so may result in accidental spraying of fuel, personal injury, or a fire hazard.
    1. Remove Fuel Tank. Fuel Pump ford-05-00-3947.gif

    2. Remove fuel pump lock ring.
    3. Remove fuel pump.
    4. Remove and discard fuel pump O-ring.
    To Install:
    1. Install new fuel pump O-ring.
    2. Install fuel pump.
    3. Install fuel pump lock ring. Tighten to 66 ft-lb (89 Nm).
    4. Install Fuel Tank.
    prev.gif next.gif

    Oct 12, 2010 | 2000 Ford Expedition

    1 Answer

    How to change a fuel pump on a 2005 Nissan


    Nissan Car Altima & Sentra 1999-06 Repair Guide
    Fuel Pump - Removal & Installation
    1. Before servicing the vehicle, refer to the Precautions Section.
    2. Relieve the pressure from the fuel system.
    3. Remove or disconnect the following:
      NOTE When the fuel sending unit needs to be removed, pull the tab upwards. The tab is located on the sending unit, opposite the end of the float. After the tab is pulled, the sending unit will lift straight out of the tank bracket.
      Negative battery cable Rear seat and the access cover Fuel pump electrical connector Fuel lines from the fuel pump assembly Locking ring Fuel gauge assembly Fuel tube and connector from the fuel gauge
      Fuel pump by pinching the 2 locking tabs together. Lift the fuel pump assembly straight upward and out of fuel tank. O-ring and discard
    4. Place a clean rag in the hole to keep out dirt.
    To install:
    1. Remove the rag
    2. Install or connect the following:
      NOTE Verify that the mark on the fuel tank and the components are aligned when installing the pump and fuel gauge sending unit.
      New O-ring and fuel pump Electrical connection and fuel tube to the fuel gauge sending unit Fuel sending unit into the tank
    3. If equipped with a threaded lock ring torque the ring to 22-26 ft. lbs. (30-35 Nm). If equipped with a lock ring held by six retaining screws, torque the screws to 18-22 inch lbs. (2-2.5 Nm).
      Fuel lines and fuel pump electrical connector. Always install new clamps on the fuel lines. Negative battery cable
    4. Start the engine, check for leaks and repair if necessary.
      Fuel pump access cover Rear seat

    The fuel pump is located in the fuel tank on all vehicles. In-tank fuel pumps are accessible by lifting up the rear seat to gain access to the inspection cover.
    1. Before servicing the vehicle, refer to the Precautions Section.
    2. Relieve the fuel system pressure.
    3. Remove or disconnect the following:
      Negative battery cable Rear seat from the vehicle Inspection cover that is located under the rear seat Inlet and outlet fuel lines from the fuel pump assembly Fuel pump and gauge wiring connections 6 mounting bolts that secure the fuel pump assembly to the top of the fuel tank
    4. Raise up the fuel pump assembly and detach the fuel tubes and connector.
      Fuel gauge assembly Fuel pump with the fuel chamber
    5. Pull up the front of the fuel pump chamber and slide the chamber forward.
      Fuel pump from the chamber O-ring seal or gasket
    To install:
    1. Install or connect the following:
      Fuel pump to the fuel pump chamber and slide chamber rearward Fuel pump with the fuel pump chamber Fuel gauge assembly using a new O-ring Fuel tubes and connector. Use new hoses and clamps. 6 mounting bolts to the top of the fuel gauge unit and torque the bolts to 18-22 inch lbs. (2-2.5 Nm) Fuel pump and gauge wiring connections New inlet and outlet fuel lines to the fuel pump assembly Negative battery cable
    2. Start the vehicle, check for leaks and repair if necessary. Inspection cover and the rear seat

    Hope helps (remember comment and rates this).

    Jul 07, 2010 | 2005 Nissan Sentra

    1 Answer

    How to change the fuel pump on a 1996 Pontiac Transport


    For 1996 Pontiac Truck Trans Sport 3.4L SFI 6cyl check this procedure for Fuel Pump... there are two different electric fuel pumps used:
    - A medium pressure twin turbine pump for vehicles equipped with Throttle Body Injection (TBI). - A high pressure roller vane pump for vehicles equipped with Sequential Fuel Injection (SFI).
    (see Figure 1)


    d7f6f20.jpg


    Fig. 1: View of the fuel pump assembly and related components
    The fuel pump is mounted to the fuel sender assembly inside the fuel tank. The fuel is pumped to the engine at a specified flow and pressure by the fuel pump. Excess fuel is returned to the fuel tank by the return pipe. The fuel pump delivers a constant flow of fuel to the engine even during low fuel conditions and aggressive vehicle maneuvers.

    CAUTION When working on or near the fuel tank, be sure to observe the information molded on the bottom of the tank.
    Removal & Installation
    1. Disconnect the negative battery cable.
    2. Properly relieve the fuel system pressure.
    (see Figure 2)


    42fbc79.jpg

    Fig. 2: Exploded view of the fuel pump-to-tank mounting components
    1. Drain and remove the fuel tank.
    2. Remove the fuel sender assembly.
    3. Disassemble the fuel pump strainer and the fuel pump: Note the position of the strainer in relation to the pump.
    (see Figure 3)


    c8d9af6.jpg


    Fig. 3: Remove the fuel tank locking ring with a non-sparking (brass) punch.
    1. Support the fuel pump in one hand, and grab the strainer in the other hand.
      1. Rotate strainer in one direction and pull off pump. Discard strainer.
    (see Figure 4)


    3c2e4a1.jpg


    Fig. 4: Exploded view of the fuel pump components
      1. Remove deflector.
    1. Disconnect the fuel pump electrical connector.
    2. Loosen the two connecting clamps, if equipped.
    3. Place the fuel sender assembly upside down on the work bench.
      1. Pull the fuel pump downward to remove it from the mounting bracket, then tilt the pump outward and remove it from the connecting hose or the fuel pulse dampener.
    4. It is recommended to replace the hose and clamps, if equipped.
    CAUTION Do not run the pump unless submerged in fuel
    To install:
    1. Push the fuel pump assembly into the attaching hose. Attach the pump electrical wires and fasten the hose clamps to the attaching hose and around the pump body, where equipped.
    2. Place the fuel tank sender and pump assembly into the fuel tank. Use a new O-ring seal during assembly.

    Hope this help (remember rated this).

    Jun 04, 2010 | 1996 Pontiac Trans Sport

    1 Answer

    I need to change my fuel filter in my 98 Dodge Intrepid. I know I need to drop the gas tank, but I'll be honest I've never did this before. I would like to have pictures to see what it looks like.


    300M, Concorde, Intrepid, LHS, 1998-2004 - Fuel Filter Removal & Installation The fuel filter mounts to the frame rail in front of the fuel tank. The inlet and outlet ends of the filter are marked for installation purposes. Install the fuel filter making certain that it is properly orientated.

    NOTE The fuel filter is part of the fuel pressure regulator mounted on the fuel pump module.
    1. Before servicing the vehicle, refer to the Precautions section.
    2. Properly relieve the fuel system pressure.
    3. Lower the fuel tank.
    4. Remove or disconnect the following:
      Negative battery cable Purge and vent lines Fuel line from the pressure regulator Filter/regulator by pushing in the locking tab, turning the regulator to unlock it and pulling the it straight up
    To install:


    7c8fc38.jpg

    Fig. Cut away view of the fuel filter/pressure regulator
    1. Push the fuel filter/regulator into the fuel pump module and turn to lock it into position.
    2. Connect the fuel lines and install the tank.
    3. Start the engine, check for leaks and repair if necessary.


    Fuel Pump - Removal & Installation
    The in-tank fuel pump module contains the fuel pump and pressure regulator which adjusts fuel system pressure. Fuel pump voltage is supplied through the fuel pump relay.

    The fuel pump is serviced as part of the fuel pump module. The fuel pump module is installed in the top of the fuel tank and contains the electric fuel pump, fuel pump reservoir, inlet strainer fuel gauge sending unit, fuel supply and return line connections and the pressure regulator. The inlet strainer, fuel pressure regulator and level sensor are the only serviceable items. If the fuel pump requires service, replace the fuel pump module.
    1. Before servicing the vehicle, refer to the Precautions section.
    2. Properly relieve the fuel system pressure.
    3. Remove or disconnect the following:
      Negative battery cable Fuel tank
    4. Clean the top of the tank to remove any loose dirt.
      Fuel lines from the fuel pump module by squeezing the quick-connect fitting with thumb and forefinger

      4edc7fc.jpg


      Fig. Using special tool 6856, remove the fuel pump module locknut
      Fuel pump module electrical connector from the top of the fuel pump module
    5. Using special tool 6856, remove the fuel pump locknut by turning it counterclockwise.
      CAUTION The fuel reservoir of the fuel pump module does not empty out when the tank is drained. The fuel in the reservoir may spill out when the module is removed.
    6. Remove the fuel pump and O-ring from the tank and discard the O-ring.
    To install:
    1. Thoroughly clean all parts. Wipe the seal area of the tank clean. Place a new O-ring on the ledge between the tank threads and the pump module opening.
    2. Position the fuel pump module in the tank. Be sure the alignment tab on the underside of the pump module flange sits in the corresponding notch in the fuel tank.
    3. While holding the fuel pump module in place install the locking ring and torque to 40 inch lbs. (5 Nm) using special tool 6856 or a spanner-type tool.
    4. Install or connect the following:
      Fuel tank Fuel pump module electrical connector Negative battery cable
    5. Fill the fuel tank with fuel. Install the fuel filler cap. Turn the ignition switch to the ON position to pressurize the system. Check the fuel system for leaks.
    Hope this helped.

    May 11, 2010 | 1998 Dodge Intrepid

    Not finding what you are looking for?
    2000 Hyundai Accent Logo

    Related Topics:

    31 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Hyundai Experts

    yadayada
    yadayada

    Level 3 Expert

    60769 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    21949 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    6811 Answers

    Are you a Hyundai Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...