Question about 1993 Oldsmobile Cutlass Ciera

1 Answer

Replace the power window motor

Front passange rside motor seems to need to be replaced. how do you remove the motor from door? how do you remove it from the tract at the motor?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,118 Answers

First door panel has to be removed, If i remember correctly there are 3 or 4 rivets that have to be drilled out to remove motor from window regulator, and unplug electrical connection, and it should come out. Replacement motor will have new blots and nuts to secure new motor back on to regulator.

Posted on Mar 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Passanger window wont roll up from driver side or passanger side


Replace the regulator. It comes with the motor. You have to remove the door panel to access it.

May 26, 2015 | 2006 Kia Sorento

1 Answer

1997 kia sportage Passenger power window stopped working from both driver's side and passanger side. Which door panel do i remove? What Next?


Sounds like the motor is bad.remove passenger panel check for voltage at motor ,if no voltage wiring is broken .if there is voltage replace motor

Jul 20, 2014 | 1997 Kia Sportage

1 Answer

My passanger front window is stuck in the down position. Could this be the window switch?


The same thing happend with my 94 lesabre. I thought it was the switch but i realized that the switch was fine. I went at the junk yard and got my self a power window motor. That is proboably what is wrong with your windows. I recommend that you get yourself new or used window motors and that sould do it!

Best of luck

Oct 10, 2012 | 1994 Buick LeSabre

3 Answers

1997 mercury grand Marquis driverside rear window motor works but window won't go up. Inner door panel off. Metal cable with a black foam cover and pink plastic clip off. Can't figure what it fits to.


usually this means you need a new window regulator.

Section 01-11: Glass, Frames and Mechanisms 1997 Crown Victoria, Grand Marquis Workshop Manual
REMOVAL AND INSTALLATION Window Regulator, Power Front Door
Removal
  1. If front door window glass (21410) is in the down position and is inoperable, the following steps must be taken; if front door window glass is operational, go to Step 2.
    1. Remove front door trim panel (23942) and front door trim shield (237A04). Refer to Section 01-05 .
    2. Disconnect battery ground cable (14301). Refer to Section 14-01 .
    3. Disconnect window regulator electric drive harness connector.
    4. sva~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Be careful not to strike or scratch front door window glass because it can break.
      Remove window regulator electric drive retaining screws through holes.
    5. Remove window regulator electric drive (23394) from front door power window regulator.
    6. Raise front door window glass to full up position by hand and secure with tape.
    7. Go to Step 5.

  2. Remove front door trim panel and front door trim shield. Refer to Section 01-05 .
  3. Remove front door window glass as described.
  4. Disconnect window regulator electric drive harness connector.
  5. NOTE: Use care not to enlarge sheet metal holes in the door inner panel.

    Remove two 1/4-inch rivets retaining lower bracket of front door power window regulator to inner panel. Use drift punch to knock out center pins for each rivet. Using a 1/4-inch diameter drill, drill out remainder of rivet.
  6. Remove three window regulator electric drive retaining screws from inside door to remove window regulator electric drive from front door power window regulator.
  7. Remove two window regulator retaining nuts.
  8. Remove front door power window regulator from front door (20124).
Installation
  1. Lubricate regulator mechanism with Teflon® Lubricant E7FZ-19590-A or equivalent meeting Ford specification ESB-M1C111-A.
  1. Install front door power window regulator minus motor (23208) into access hole in inner panel.
  1. Position front door power window regulator using upper studs and tabs on window regulator electric drive mounting bracket.
  1. Install rivets retaining front door power window regulator to door inner panel (1/4-20 x 1/2 inch screw and 1/4-20 nut and washer assemblies or equivalent metric fasteners may be used).
  1. Install two upper front door power window regulator retaining nuts.
  1. Install window regulator electric drive with three screws. Do not overtighten screws.
  1. Connect the window regulator electric drive harness connector.
  1. Install front door window glass.
  1. Adjust front door window glass as described.
  1. Install front door trim shield and front door trim panel. Refer to Section 01-05 snorkelbobby_38.gif

Feb 14, 2011 | 1997 Mercury Grand Marquis

1 Answer

Back passanger window has come off track/cables. What is the best fix...the window has dropped to the bottom


you will need to replace the window regulator assembly.

this is a one piece design with the window motor, cables and rails serviced as an assembly.

you will need to remove the door panel, pull the window back up and wedge cardboard between the glass and door, remove the two bolts holding the glass to the regulator, remove the couple of bolts holding the regulator assemblt to the door, unplug window motor, and replace with new assembly.

this is not a tough repair, with basic handtools and common sense anybody can make the repair

good luck

wesleyschacht@hotmail.com

Jun 14, 2009 | 2001 Chrysler Sebring

1 Answer

Replace front passenger power window motor


not hard at all remove the door panel and you will see 5 bolts with a slot so you do not have to remove the bolts just loosen them. There is 2 clips that hold this to the window remove them. The hole thing will come out. Look on E Bay buy a new window regulator $40.

May 31, 2009 | 1999 Jeep Grand Cherokee

1 Answer

Front right passanger window motor need to be repace, I have taken off the panel but unsure on how to get the motor out


First disconnect your negative battery cable. Next locate and remove the screws that hold your interior door handles in place (they may be hidden by snap in, or snap on clips). Once you have removed the interior door handles, unplug the wire clips to the switches. Next you will need a small pry bar to remove the door panel itself. The door panel is held in place by snap in clips; try to get the pry bar as close to, or directly under the clips, to prevent them from tearing out of the door panel. Once you have removed the clips, pull the panel upward to remove it from the door. You will need to remove the plastic sheeting to gain access to the window regulator. You will need to remove the regulator and motor as a single unit, and once it's removed you can replace the motor.
Install everything in reverse.

May 23, 2009 | 2004 Chrysler Sebring

1 Answer

How to replace window regulator


you will need to drill out some rivets. Replace with ntus and bolts and washers & lock washers. Make sure they don't hit glass going up and down. Otherwise you will need a heavy duty riveter.
please rate as fixya if this helps.

Motor —Front Door
Special Tool(s) swj~us~en~file=st1132a.gif~gen~ref.gif Heavy Duty Riveter
501-D011 (D80L-23200-A) or equivalent
Removal
NOTE: The window regulator and motor are removed as an assembly.
  1. Remove the front door trim panel. For additional information, refer to Section 501-05 .
  1. Remove the front door radio speaker.
  1. Remove the latch remote control. For additional information, refer to Section 501-14A .
  1. Remove the front door watershield.
  1. swj~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Support the window glass to avoid damage.
    Raise and support the front door window glass to the full up position.
  1. Disconnect the power window motor electrical connector.
  1. Remove the window glass to regulator nuts.
  1. Remove the motor and window regulator assembly.
    1. Drill out the rivets.
    1. Remove the motor and window regulator assembly.
88565ca.gif
  1. NOTE: Prior to motor removal, make sure the regulator arms are in a fixed position to prevent counterbalance spring unwind.
    Remove the power window motor.
    1. Remove the bolts.
    1. Remove the power window motor.

Mar 21, 2009 | 1998 Ford Expedition

1 Answer

Front passanger window not working.fuse checked;


it is most likely the window motor has failed.

Mar 19, 2009 | 1996 Ford Escort 4 Door

2 Answers

2000 dodge caravan window motor


You have to remove the door panel first, After the door panel is removed you have to remove the window motor AND the cable system in the door. When you install the replacement window motor/regulator, you'll have to slightly modifiy the inside of the door frame for it to set in properly, when you get to that point you'll see what I'm talking about.

May 16, 2008 | 2000 Dodge Caravan

Not finding what you are looking for?
1993 Oldsmobile Cutlass Ciera Logo

331 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...