Question about 2000 Lexus ES 300

1 Answer

When the car is exposed to the sun, my remote to lock or unlock the car doesn't work anymore. I have no problem in the winter. the circuits probably heat up. What can i do?

Posted by on

  • coxtol Mar 05, 2009

    Thanks for the answer but it cannot be the keyless entry battery because i know the car receives the signal. the two side doors where the sun hits do not open but the other two do. Also, I can hear the car beeping and/or making a sound when pressing on the remote. I am positive that the keyless entry signal to the car is good and that it has something to do with heat.



    Thanks but do you have any other suggestions?? Anybody else??

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

Try replacing the keyless entry battery and see if that helps... when the battery begins to wear it lessens the signal quality

Posted on Mar 05, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can't start truck after battery change or unlock the doors


turn ignition switch on position for 20 seconds then try to lock and unlock doors.if you have sun roof open sun roof fully then close sun roof fully. then switch off ignition switch then try to start.

May 22, 2013 | Land Rover Range Rover Cars & Trucks

1 Answer

On my 2006 Chrysler 300/ the auto lock button on my key remote doesn't lock or unlock doors?


how do I reset one of two keys that the unlock,lock,trunck does't work but the key turns the engine over.

Oct 08, 2012 | 2006 Chrysler 300

1 Answer

I need to know how to program my universal keyless remote control to my gmc yukon


This is the procedure to reprogram your remote:

Press and hold the drivers side UNLOCK button.

Insert the key into the ignition, Turn ON, OFF. (do not start)

Repeat 2X. (3 times total)

Locks should cycle to indicate program mode.

Press and hold LOCK and UNLOCK on the Remote to be programmed. (may take up to 30 seconds)

Locks should cycle to indicate successful programming.

Ignition ON to exit program mode.


If it still doesn't work after this you probably have a bad remote. Hope this helps.

Dec 18, 2011 | 2003 GMC Yukon XL

2 Answers

Remote control won't lock/unlock doors, but will open the trunk. What;s wrong?


There is a fuse box under the right rear seat cushion behind the driver. In that box is a 10 amp mini fuse marked "TRUNK DR RELEASE". That is the fuse that powers your remote receiver. If that fuse is good, the receiver may have failed. To remove the seat cushion, pull the front of the cushion up and then forward.

Nov 02, 2011 | 2003 Cadillac CTS

1 Answer

My keyless remote doesn't work anymore to open my car doors an to set alarm, while walking away to or from vehicle...bought new battery for remote an it still doesn work...have to lock an unlock by hand...


before you spend too much money...try this.
On the inside of the keyless remotes, there are rubber buttons, those rubbers buttons are brushed with metal of some sort so that it reacts with the motherboard, when the remotes get older this metal wears off...so try this, it worked for me...
I superglued foil paper to the back of the button (the parts that touches the motherboard when pressed) and replaced the batteries... it worked like a charm, I used an awl and a hammer to make perfectly round piece of foil and just glued it onto the back of the button... i'd try this first before spending any real money.

Oct 10, 2010 | 2000 Mitsubishi Montero

1 Answer

Key fob stopped working the door locks. I changed


the circuit boards on those factory remotes, sometime break where the battery is clipped in, check to make sure the solder is holding the clip properly and it is not loose, also they remote may need to be programmed to the vehcile with a scan tool, usually only found at GM, Also the rubber part of the remote on the inside where the pad touchs the circuit board, uses a small screwdriver and touch the exposed circuit, if the remote locks the doors, try putting in tiny peice of alumumn tape of the inside pad, the connectiveness of the rubber wears off. If not try above or dealer.

Sep 28, 2009 | 1999 Chevrolet Silverado 1500

2 Answers

2004 infiniti g35 coupe doors do not lock with button/remote


can you unlock them with remote if not and you have changed the battery in it the remote has probably lost its programming. if you can the circuit for the unlock is probably bad.

Aug 28, 2009 | 2004 Infiniti G35 Sport Coupe

3 Answers

My key fob remote will not unlock car doors but will start car


Here you go.If you can't read it I can email it to you.
c2293a3.jpg

Aug 04, 2009 | 1998 Porsche 911 Carrera

1 Answer

The auto door locks on my 1991 buick regal quit or only work intermittenly. I bought a new transmitter (hand unit) and replaced the relay under the dash. The dealer could only program the new hand piece to...


I had they same problem a few years back. Aging electronic circuits may be the issue here. That is what happened to cause the remote door feature to operate intermittently in my 1991 Buick Regal. Over time the heat of summer and the cold in winter stress solder joints on printed circuit boards. That stress can bring about what is known as cold solder joints.

I located the remote door receiver module behind the back seat under the cover that holds the Third Brake Light. Once removed from the car I opened the module up and inspected the printed circuit. Sure enough I saw the problem using a magnifying glass. Many of the solder points had cracks around connectors, resistors, capacitors to name a few. Resoldering each bad point sovled the intermittent operation. I hope this helps...

Apr 19, 2009 | 1991 Buick Regal

Not finding what you are looking for?
2000 Lexus ES 300 Logo

Related Topics:

62 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lexus Experts

yadayada
yadayada

Level 3 Expert

63661 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21986 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Lexus Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...