Question about 2002 Mazda Protege

Open Question

Mazda protege tranny problems

I have a 2001 protege ES 2.0. when i first got the car it wouldnt move in R or D. Change the fluid and filter and the vehicle started to move after getting it to move it will cut off when put it in gear and when accelerated to keep it running it will be jumpy and vehicle would have no power for 5 secs then the car will take off. sometimes while driving it would stop pulling and O/D would start blinking. check the solenoids with checking each resistance and they was all in spec and also check wiring and that was good any help will be good

Posted by on

5 Suggested Answers

  • 2 Answers

SOURCE: how to adjust caliper for rear brakes on a Mazda Protege Es.

yep, this is what u do. i read that this controls hand break and you need to completely loosen that using hex (3mm) key. BUT, when u tighten it back up, u need to unscrew it about 1/8th, VERY important, or ur pads will be rubbing way too much against the rotor. I actually had to do about 1/2 the turn to make the wheel spin w/out too much pressure.

Posted on May 03, 2009

c17hydro
  • 2984 Answers

SOURCE: I need the specs for a 1990 mazda protege cruise

174b705.gif
Mazda vehicles used both vacuum actuated and electric stepper motor type cruise control systems. The actuator, located in the engine compartment, will have a vacuum line and electrical wires connected to it if it is a vacuum model. Electric stepper motor type units will have no vacuum line connected to the actuator.


9bb13ff.gif

Posted on Jun 23, 2009

  • 5 Answers

SOURCE: Mazda Protege ES 2001,speedometer and odometer

Vehicle speed sensor. See if you can buy one of those cheap OBD2 scan tools Wal-mart sells, and if you have a P0500 in the PCM, I would place my money on a broken sensor. It costs about $60

Posted on Jul 23, 2009

  • 2 Answers

SOURCE: where is the blower motor resistor on a 2002 mazda protege?

just remove the glove box and its right behind it just take the white pug out and the two phillips screws to remove the resistor out, replace with the new one and cool off!!!! Hope this helps

Posted on Aug 04, 2009

  • 14036 Answers

SOURCE: 01 mazda protege camshaft torque specs

CAMSHAFT BEARING CAPS TORQUE TO 125 INCH POUNDS. CAMSHAFT SPROCKETS - 44 FT LBS. YOU NEED A REPAIR MANUAL LIKE A CHILTON WITH CAMSHAFT TORQUE SEQUENCE DIAGRAM. YOU HAVE 20 CAMSHAFT CAP BOLTS THAT HAVE TO BE TORQUE IN SEQUENCE.

Posted on Mar 21, 2010

Testimonial: "Thanks that was very quick and right on he money "

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Automatic transmission


check fluid level and filters on tranny

Jul 14, 2013 | Mazda Protege Cars & Trucks

2 Answers

Where is the fuel filter located on a 2001 Mazda Protege 2.0 LX?


A 2001 Mazda Protege (actually, all models from 1999-2003 including the DX, LX, ES, Mazdaspeed, and Protege 5) does not have an inline fuel filter. The only fuel filter it has is a "strainer" or a "screen", which looks like a nylon mesh "sock". This strainer is connected to the fuel pump, located in the gas tank. Although this fuel strainer does not require periodic replacement, it is recommended that it be changed if you are replacing the fuel pump.

Jun 15, 2010 | 2001 Mazda Protege

2 Answers

Replace fuel filter on 2000 mazda protege


A 2001 Mazda Protege (actually, all models from 1999-2003 including the DX, LX, ES, Mazdaspeed, and Protege 5) does not have an inline fuel filter. The only fuel filter it has is a "strainer" or a "screen", which looks like a nylon mesh "sock". This strainer is connected to the fuel pump, located in the gas tank. Although this fuel strainer does not require periodic replacement, it is recommended that it be changed if you are replacing the fuel pump.

May 03, 2010 | 2000 Mazda Protege

2 Answers

1997 Mazda protege LX 1.5 automatic transmission


You are going to need a transmission shop. Mazdas do not always throw codes. You have an early OBD transmission, which do not send out many codes.

Aug 02, 2009 | 1997 Mazda Protege

1 Answer

My 2001 BUICK CENTURY TRANNY STOPS WORKIN AFTER 3 MIN.


Might want to remove the pan and look how much debris is in there. they can draw debris into the filter for like 15 minutes until it just wont let any more fluid go by then trans will neutralize. when you let it sit the debris by gravity falls back to the bottom of the pan. If this is the case changing fluid and filter may be a temporary fix but honesly when theres that much debris in there it needs rebuilt--in fact sometimes after fluid and filter change they wont move at all. The thick fluid and dirt provides some pressure. Hope I helped. Thanks

Apr 06, 2009 | 2001 Buick Century

1 Answer

Idle 2001 mazda protege ES 2l


relpace the fuel rail pressure regulator

Dec 24, 2008 | 2001 Mazda Protege

1 Answer

Repair manual


http://www.tradebit.com/filedetail.php/2356789-2000-2004-mazda-protege-repair-service

try this or search other sources online
good luck

Nov 10, 2008 | 2001 Mazda Protege

1 Answer

1995 mazda protege having problems running during aceleration


change the transmission fluid, replace the oil and oil filter check spark plug cables, check starter coilpak, and make sure there is coolant

Jul 02, 2008 | 1995 Mazda Protege

Not finding what you are looking for?
2002 Mazda Protege Logo

Related Topics:

87 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

63577 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...