Question about 2005 Chevrolet Colorado

1 Answer

I like to think Im smarter than the average bear,but is it harder to change the front rotors on a 05 Colorado 4x4 than other rotors?

Posted by on

  • flirtwinslow Mar 04, 2009

    Thanks,Its just been awhile and with this truck ,it appears that just about everything needs to have either something scanned,probed or just plain over complicated!!! LOL!!! Thanks for the reply.I cant afford to run to the dealer for everything!!!

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,055 Answers

No its about the same as any gm truck

Posted on Mar 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Replaceing front hub bearings on '05 GMC sierra 4X4


Remove the caliper & rotor,axle nut & unbolt
the axle hub bearing assy

Watch some video on it

You do both sides at the same time

Aug 14, 2014 | Cars & Trucks

1 Answer

Is there any difference between replacing front breaks/ rotors in an 87 cougar and any other car? Autozone tells me the wheel bearing and hub assembly are all part of the rotor. Is this true? Is it any...


This the old fashioned rotor. The hub is part of the rotor and there will be an inner and outer bearing. In order to replace the rotor the old bearings will need to be removed from the old rotor, cleaned, inspected, repacked, and then reinstalled in the new rotor along with a new grease seal.

Most newer vehicles have whats called a knock off rotor. This type of rotor simply slips off from the hub assembly once the brake caliper is removed.

Sep 17, 2011 | 1987 Mercury Cougar

1 Answer

Have grinding noise in the front area of the vehicle...changed right and front wheel bearings still has a light roar....this is a 4x4 truck... please help


what type of vehicle,auto or manual hubs, check front u-joints. since you replaced hubs i imagine you inspected brake parts and rotors. could also be a wheel bearing in front pig. (carrier bearing or pinion shaft bearing)

Apr 11, 2011 | Chevrolet Silverado 1500 Cars & Trucks

1 Answer

Can't get plate off in front off rotor on my 99 dodge 2500 4x4 v10. took off large hub nut and it still wont budge.


Do you want to remove the rotor or the hub and all? To remove the rotor, the caliper has to be out of the way and the bracket that holds it on. The nut in the middle holds the axel into the front wheel bearing and it's a press fit. The axel can be removed and the steering Knuckle can be removed and the knuckle be put on a press to push the hub out of the bearing. This destroyes the bearing and you need to plan on new bearings. They do make a puller that can be rented at the parts store that can pull the hub. once the hub is pulled out of the bearing the rotor can be unbolted from the back side of the hub. It's best to do this work on a press as the bearing needs to be installed with out damage and it's harder to get it right with a sleigh hammer.

Oct 27, 2010 | 1984 Dodge Pickup 4WD

1 Answer

How do I change front hub and bearing assembly on 2004 Explorer


Front hub bearing, remove tire, remove caliper and caliper holding bracket, you do not have to remove brake caliper from brake hose, just set it aside, if 4X4 remove front axle nut that goes through center of rotor, also remove brake rotor, disconnect elec, A.B.S connector, remove three bolts on back side of hub bearing, remove hub bearing, some times you will need to knock hub bearing out with a hammer.Reverse to install new hub bearing.

Jul 09, 2010 | 2004 Ford Explorer

1 Answer

Left front hub replacement 2WD.


2WD pickups don't have hubs. They have rotors with bearings. Once you have the brake assembly supported, remove nut from spindle. Be sure not to strip the threads on the spindle. Remove the front set of bearings and pull the rotor off. Remove the rear set of bearings. Be sure to pack greases into new bearings prior to installation. Insert new rear bearing into rotor and replace onto spindle. Insert new front bearing and washer and re-install nut. Tighten to recommended torque specs, grease fittings and replace brake assembly.

May 15, 2010 | 2005 Chevrolet Colorado

1 Answer

I have a 95 dodge 3500 4x4 service truck when u put it in 4wheel drive it seems like something binds and then pops and then it will roll again im thinking maybe the pinion bearing because i replaced both u...


lift front axle and place on jack stands. place front axle on 4x4 and rotate wheels by hand. If front axles are harder to turn than normal then remove drive shaft from transfer case and rotate front axle once more. this will let you know if the problem is in the front axle or in the tranfer case

Mar 21, 2010 | 1995 Dodge Ram 3500

2 Answers

How to remove and replace front brake rotors chev colorado


Time to buy yourself a good shop manual. You say it is both a 2006 and a 2008.

May 12, 2009 | 2008 Chevrolet Colorado 2WD

2 Answers

I am looking at a 2004 colorado with 3.5 5 cyl. engine with 115k. how is this vehicle performance and reliability


My 2004 Colorado 4x4 is at 91K and running better than I would have expected. It seemed to break in at 80K. Still getting 21 mpg. Haven't changed spark plugs yet. No major repairs have been needed except for the power steering pump I'm about to replace because of a squeal.

Apr 15, 2009 | Chevrolet Colorado Cars & Trucks

Not finding what you are looking for?
2005 Chevrolet Colorado Logo

Related Topics:

142 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...