Question about 2000 Ford Expedition
If you look up under the steering wheel you will see a box with 5 large numbers on it those 5 numbers are your code. i had same problem until i had someone tell me
Posted on May 01, 2009
It is under the dash by where your left foot would rest - there is a cream box and it has 5 large numbers and that is your code
Posted on Jun 22, 2009
The code is on a plastic card in your owner manual packet. You can use that code or you can change it to any code you want.
Your delaer can provide your code and they can hook up the diagnostic tool and retrieve your code. Finally, provide your 17 digit VIN to your delaer and show your registration to prove you are the owner and they can call Ford for the number too.
Posted on Mar 04, 2009
What fivelarge numbers under your stearing wheel are your lock code numbers
Posted on Jun 13, 2009
The easiest way to get the code for the door pads is to go by ford and have them pull the codes or even reset the code to your liking
Posted on Mar 04, 2009
Look under your steering wheel right under the dash. There should be a small white strip with 5 numbers. This is your master code for your vehicle. If you bought the car used and they give you a code, they could have made their own code, but the master will override it. If this don't help, the module for the doors may be going bad.
Posted on Jan 05, 2010
You should check your blend door, go to the center of your dash look down towards the floor right at the bottom on the hump (tunnel area) you will see a black or same as interior color, cover it has small slits cut in it, it is held in by two expanding type plastic bolts, they do not unscrew, just pull them out, one on each side. Once removed locate the white small box with a wiring harness connected to it, a little to the right hand side. This is the stepping motor that controls the blend door. Remove the stepping motor, and reconnect the harness, look at the motor drive unit and operate the heater control knob, does the motor turn, if it does then use a mirror and look at the drive end of the blend door itself, it is probably broken. If the door is broken, this repair just got difficult, the entire dash will have to be removed to access the environmental station, once accessed there are about 10 screws that hold the top cover on the enviromental station, undo these screws and remove the top cover, then you can remove and replace the blend door. If you are not comfortable with this difficultly level in repair I suggest you seek out your favorite local shop. removing the dash is not easy, there are alot of screws, some in very difficult places to reach. Testing the motor is easy. I hope this helps, let me know.
Posted on Jan 20, 2010
Look under the driver's side of the dash. There is a white box that should have the keyless code on it. It is located near the parking brake and fuse box.
Posted on Jan 22, 2010
If you smell antifreeze it may be 3 possibilities: 1. you may have a leaking hose/hose connector , or water pump. 2. your heater core is bad and needs replaced. Unless you know what you are doing I would highly suggest taking to dealer for heater core replacement. The dash and steering colum has to be removed to get to the heater core. This is not an easy job believe me (about-900-1200 job). If you have your heater core replaced then also replace the climate control door. This is good preventative maintenance and also a a dollar saver. I would have a pressure check run on your radiator as a first thought. All you may have is a bad hose and that can easily be replaced.
Posted on May 20, 2010
SOURCE: to find keypad code's for
The Factory Door Entry Code--came with your owners manual,if you forgot, what you programmed in.
Other wise, it is off to the dealer to solve. My be able to use your VIN and title and reg, to have them help you
Posted on Oct 14, 2010
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Tips for a great answer:
Feb 23, 2015 | 2004 Ford Expedition
Feb 10, 2013 | 2000 Ford Expedition
Nov 07, 2011 | 1999 Ford Expedition
Jan 05, 2011 | 2000 Ford Expedition
Programming your own personal entry code
To program your own code:
1. Enter factory set code (keypad will illuminate when pressed).
2. Press 1/2 control within five
seconds of step 1.
3. Enter your personal 5 digit code.
Enter each digit within five seconds
of previous one.
Do not set a code that includes five
of the same number or presents
them in sequential order. Thieves
can easily figure out these types of codes.
Your personal code does not replace the permanent code that the
dealership gave you. You can use either code to unlock your vehicle. If a
second personal code is entered, the module will erase it in favor of the
If you wish to erase your personal code, use the following instructions:
1. Enter factory set code.
2. Press 1/2 control within five
seconds of step one.
3. Press 7/8 control and 9/0 control
at the same time within five seconds
of step 2.
The system will now only respond
to the factory set code.
Oct 28, 2010 | 2000 Ford Expedition
Oct 14, 2010 | 2008 Ford Expedition
Jul 26, 2010 | 2000 Ford Expedition
May 18, 2010 | 2000 Ford Expedition
Mar 29, 2010 | 2000 Ford Expedition
Jan 21, 2010 | 2000 Ford Expedition
329 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: