Question about 1992 Toyota Land Cruiser

Open Question

Removal of starter from 1992 toyota land cruiser

No access to mounting bolts

Posted by on

6 Suggested Answers

SOURCE: 1997 Toyota Land Cruiser rain water leak

i had the same problem. Flushed the sunroof drains, replaced the windsheild, and weather stripping on passenger and driver side doors. Car is still leaking. No one can figure it out.

Posted on Jul 31, 2008

Technopro
  • 243 Answers

SOURCE: quantity of engine oil used in 1 HD engine toyota land cruiser

The Landcruiser 1HD engine uses 9.3 liters of oil with the filter. The oil is replaced every 5000Kms.

Posted on Nov 12, 2008

  • 101 Answers

SOURCE: Trying to remove and replace rear brake rotors

First, make sure your parking brake is off.
Remove the rear caliper and then the brake pad housing. In the center hub of the rotor the parking brake shoes are located. The may need to be loosen first. There is a hole between 2 of the studs you need to align at the bottom. Look in the hole with a flashlight and find the star wheel. Use a screw driver to turn the wheel up a few turns to loosen the parking brake shoes from the rotor hub.
After that there are 2 threaded holes in the rotor near the studs you put two 8mm bolts in and slowly tighten each and it will pull the rotor off the hub. They rust up pretty bad so use penetrating oil on them.

Posted on Apr 11, 2009

  • 35 Answers

SOURCE: wheel alingment specs for toyota land cruiser

Camber
Left−right error
1°00’ ± 45'

Caster
Left−right error
3°00’ ± 1°

Steering axis inclination 13°00’ ± 45’
Camber, caster and steering axis inclination are not adjustable.
If measurements are not within the specification, inspect the
suspension parts for damaged and/or worn out parts and replace
them as necessary.


INSPECT TOE−IN
Toe−in
(0.08 ± 0.08 in.


This is the only Land Cruiser Specs I could find, hope it helps

Posted on Apr 18, 2009

  • 1 Answer

SOURCE: Toyota Land Cruiser Prado (LC90) Owner's Manual (free download)

hi sir/mam,i have tryed to get help from allover,can i know who can.
i have Toyota land cruiser Model GF-RZJ 95W-GKPSK-D.
Engine-3RZ-FE.
Fram-no rzj95-0047087.
This vehical does not start,Digonest code 002:-Fauity RPM Signal(no RPM,NE and crankshaft position signal trnsmitied to ECU after started for 2 secondes)
1.CKP and CMP sensors short open
2.Distibutor fault.
3.start circuit open or short.
4.module fault.
i have changed distibuteor (NEW)

Posted on Jun 26, 2010

  • 1 Answer

SOURCE: toyota land cruiser 1997 80 series electrical wiring diagram

what are the colour of the wires for the unlock / lock for the central locking for a toyota landcruiser 1990 modle ?

Posted on Jul 04, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace a radiator on a1994 toyota land cruiser


dak408_129.gif

  1. Disconnect battery ground cable.
  2. Drain engine coolant.
  3. Remove battery and tray,
  4. Remove radiator grille
  5. Disconnect No. 3 water bypass hose.
  6. Disconnect radiator inlet hose.
  7. Disconnect coolant reservoir hose.
  8. Loosen water pump pulley mounting bolts.
  9. Loosen lock, pivot and adjusting bolts of alternator and remove drive belts.
  10. Disconnect oil cooler hose from clamp on fan shroud, then remove shroud.
  11. Remove water pump pulley mounting nuts.
  12. Remove fan with fluid coupling, water pump pulley and fan shroud.
  13. Disconnect transmission oil cooler hoses.
  14. Disconnect radiator outlet hose.
  15. Remove radiator brackets, then the radiator.
  16. Reverse procedure to install.

Dec 11, 2010 | 1994 Toyota Land Cruiser

1 Answer

Replace starter on 92 4runner 3vze 3.0 liter


The starter comes out from the passengerside wheel well.Disconnect battery, then jack up vehicle and put a jack stand under the car on the frame. Remove the cover up in the wheel well. Remove front skid plate to gain access to the lower starter bolt. Remove wire hooked to starter and to motor mount. Remove two small bolts on heat shield. If vehicle is an automatic remove kickdown cable bracket. Upper starter bolt can the be removed and the starter will come out.

Oct 25, 2010 | 1992 Toyota 4Runner

1 Answer

I have a 1983 Land Cruiser and when I start it, there is a terrible grinding, rattling noise. It starts up strong, and I replaced the starter 1 1/2 years ago. Any suggestions as to what else I might look...


Before you really panic, check the mounting bolts on the starter. I feel positive you will find them lose! Changing the ring gear is last resorte. For now let's just check the bolts. OK?

Apr 16, 2010 | 1983 Toyota Land Cruiser

1 Answer

I need instructions on how to replace the starter on a 2000 Toyota Land Cruiser


[Get the Flash Player] function launchVid(flashVars) { var s1 = new SWFObject('http://www.delmarlearning.com/webservices/delmedia/JWPlayer/Default/player.swf','ply','400','300','9','blue'); s1.addParam('allowscriptaccess', 'always'); s1.addParam('allowfullscreen', 'true'); s1.addParam('flashvars', flashVars); s1.write('vidPlayer'); $.scrollTo('#vidPlayer', 1000); } On all engines except the 2UZ-FE, the starter is external, mounted in a conventional manner, alongside the engine block. One the 2UZ-FE, however, the starter is mounted in the 'V' of the engine, between the cylinder head banks. The entire intake manifold assembly must be removed to access the starter motor and solenoid. (Toyota calls the solenoid a "magnetic switch.")
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Drain the cooling system.
  3. Relieve the fuel system pressure.
  4. Remove or disconnect the following:
    • Negative battery cable
    • Engine appearance cover
    • Air intake tube
    • Intake manifold
    • Starter motor mounting bolts
    • Starter wiring connectors
    • Starter motor
To install:
  1. Install or connect the following:
    • Starter motor
    • Starter wiring connectors. Tighten the cable nut to 86 inch lbs. (10 Nm).
    • Starter motor mounting bolts. Tighten the bolts to 29 ft. lbs. (39 Nm).
    • Intake manifold
    • Air intake tube
    • Engine appearance cover
    • Negative battery cable
  2. Fill the cooling system.
  3. Start the engine and check for leaks.

EMAIL ME AT bomber6509@yahoo.com for the diagram....it is too large to post here...there is no charge.

Oct 11, 2009 | 2000 Toyota Land Cruiser

1 Answer

Starter motor


hi there,
shut down the engine for atleast 30 minutes to cool,the starter motor was located under beneath the engine,the pinion driver was coincide to flywheel,if you want replace starter motor,disconnect starter regulator cable, loosen two bolt on the engine starter motor holder,try to swicth starter motor on a free way that could go out on mounting space,the exhaust manifold mostly is behind the way of starter motor if hard to pull out,if necessary disconnect exhaust manifold replace exhaust manifold gasket,distortion on manifold gasket may happen after removing manifold
. pull out starter motor and replace a new one, put back also exhaust manifold if you disconnect it.
set fender covers on each fender to prevent paint damage
select the correct size open end box end wrench or ratchet, socket and extension. This procedure is much easier using the ratchet, socket and extension. Use your wrench to remove all of the manifold mount bolts. The manifold will now be free enough to access the gasket behind it
remove the old gasket using your putty knife. The gasket should come of mostly intact. Use your putty knife to remove any gasket material that remains on the engine block or the manifold. Any gasket material left on the mounting surfaces will cause leaks that inhibit engine performance coat the new gasket on both sides with a light coat of anti-seize compound. Put the new gasket in place against the block mounting surface. The anti-seize compound will hold the new gasket in place and prevent the gasket from sticking to the mounting surface, making future repairs easier.
push the manifold in against the new gasket and the block. coat the threads of your manifold bolts with a light coat of anti-seize compound. This will protect the threads on the bolt and the mounting surface. Start all manifold bolts by hand to ensure that the manifold is positioned evenly against the block. Be sure that the gasket remains lined up with the mounting holes. If the gasket slips out of position it will leak.
use your wrench or a torque wrench if required by the service manual to tighten all manifold bolts. Start the engine and check for any leaks. no leaks means you are done.
have a nice day don't forget to rate me,thanks a lot.

May 20, 2009 | 1995 Toyota Land Cruiser

1 Answer

I need the torque settings for head bolts on a land cruiser ,it is a 1997


Hope this helps. Please dont forget to rate my advise. Thanks
Lefty64



0900c152802619a6.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. New head bolts are strongly recommended. Tighten the head bolts down uniformly using this sequence in several passes2RZ-FE and 3RZ-FE engines
  1. Tighten all bolts to 29 ft. lbs. (39 Nm).
  2. Mark the front of the bolt with paint and retighten bolts 90° in the proper sequence.
  3. Retighten an additional 90°. Check that the painted mark is now facing rearward.

Apr 09, 2009 | 1992 Toyota Land Cruiser

2 Answers

Starter location on 1999 Toyota Landcruiser


jack up the truck , remove the right front tire than remove the small little panel at the top left of the inner wheel whell. just above and to the rear of the shock mount. it should be mounted on the right lower side of the motor with 3 hard to get at bolts.

Mar 29, 2009 | 1999 Toyota Land Cruiser

1 Answer

Looking for proceadure replacing power steering pump for '96 toyota landcruiser.


syphon PS fluid, pinch hoses, remove belt, remove mounting bolts, remove pump.
rinse, lather, repeat.

Mar 26, 2009 | 1996 Toyota Land Cruiser

1 Answer

Auto transmission removal


remove the transmission. the torque converter should just stay on the motor. if its bolted the engine the bolts will now be uncovered. if its a slip on mark the converter and the shaft to make sure you line in back up right.

Sep 24, 2008 | 1996 Toyota Land Cruiser

Not finding what you are looking for?
1992 Toyota Land Cruiser Logo

Related Topics:

50 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...