Question about 1994 Toyota Celica

1 Answer

Need to replace rear brakes

Not sure how to remove the old brakes

Posted by on

  • c38hot May 11, 2010

    brakes are a safety item , if not sure of proper way to service then maybe qualified technician should do it , for your own safety

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,533 Answers

Try your local library and they will make copies and print out diagrams for you of how to do the job safely

Posted on Mar 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Changing the rear brake pads and can't compress the piston into the caliper- any ideas? 2003 rendezvous


FIRST REMOVE SMALL AMOUNT OF BRAKE FLUID FROM THE BRAKE MASTERCYLINDER. THEN USE A LARGE C - CLAMP AND LEAVE THE OLD BRAKE PAD IN PLACE ON PISTON SIDE THEN COMPRESS THE PISTON IN CALIPER BORE. IF YOU SEE SIGNS OF BRAKE FLUID LEAKING AROUND PISTON SEAL.THE BRAKE CALIPER NEED REPLACING.WHEN YOU FINISH BRAKE JOB NEW BRAKE SHOES IN PLACE MAKE SURE BRAKE MASTERCYLINDER COVER BACK ON MASTERCYLINER THEN PUMP BRAKE PEDAL UNTIL NEW BRAKE PADS SEAT AGAINST BRAKE ROTOR.CHECK BRAKE FLUID LEVEL IN MASTERCYLINDER MAKE SURE ITS NOT LOW.

Aug 12, 2011 | 2003 Buick Rendezvous

2 Answers

How do i take off the brake drums on a 2003 chevy cavalier


After you remove the tire, the drim should slide off. If it doesn't then try using a rubber mallet and gently tap on the outside edge as you pull on it. Sometimes you also need to tap on the drum in the center part. I have sprayed penetrating lubes like WD-40 or PB Blaster into the seam at the center. You may also have to back off the parking brake cable or even use the adjuster to back off the shoes.

Jan 27, 2011 | 2003 Chevrolet Cavalier

1 Answer

Change rear wheel bearing is it hard to do ford fusion 03


Lightly losen the lug nuts with the tires on the the ground. Jack up the car and remove the tire according to the owner's manual. Make sure to block the wheels. After the tire is removed, release the park brake. Support the car on jack stands. Remove four bolts from the rear of hub. The hub nut will be 29 mm - it is important that you have a tight fit if you attempt to remove the nut.

At this point you MAY have to loosen or remove the remove the emergency brake cable. Either way the hub is ready to be removed. The front of the hub (with the lugs) and the bearing will come out and the back plate and brake shoes will remain in place.

Once you get it off, you may either purchase a hub assembly (which includes the hub with a new bearing in place ready-to-go) or take the existing hub and a replacement bearing to an auto machine shop which can easily remove the old bearing and install the new bearing. Using extreme care you can remove the old one using bearing pullers and prybars and replace the bearing using large deep sockets or a properly sized piece of steel pipe.

Since you have the hub apart, you should inspect the brake shoes and (brake) wheel cylinders and replace them as needed. Replace brake parts on both sides if you replace them on either.

Put the hub back into the brake shoes. It may only line up one way. Finger tighten ALL FOUR of the bolts and then tighten. Replace the tire and remove the lifting equipment. Start slowly so the brakes can readjust!

Sep 17, 2010 | 2004 Ford Focus

1 Answer

1995 f350 ford 2 weele drive dually rear drum removal.....do I gotta pull axle? Do I gotta replace seal?


Unfortunately you will have to remove the axles on that model of truck to access the brakes and it is necessary to replace the seals at this time because you will probably cut the old seals upon removal.I would recommend that if you are going to check them you at least need to clean and de glaze the old shoes if you don't replace them!!!! make sure to use a good quality brake cleaner.

Aug 31, 2010 | 1995 Ford F350

1 Answer

Replace rear brake pads


Rear disc brake pads offer better performance and are not as affected by moisture like conventional brake shoe style brakes are. Rear disc brakes are similar to front disc brakes. The main difference is that rear disc brake systems must incorporate the emergency brake system. There are two methods widely used for the emergency brake with rear disc systems. The first system is a brake shoe inside the brake disc that is actuated by the emergency brake lever. The second is a screw style actuator inside the brake caliper. When activated the brake pads are forced into the brake disc and held tightly by the emergency brake lever.
READ COMPLETELY BEFORE STARTING
Step 1 - Identify Rear Disc Brake Components
rear_brake_pads.jpg Rear disc brake assembly includes; rear brake disc, rear brake pads, brake caliper mount and a caliper mounting screw. (Note: Some vehicles do not have the rotor mounting screw.)
Step 2 - Removing the Rear Brake Caliper Mount Bolts
rear_brake_pads_2.jpg To replace rear brake pads and rotors the rear brake caliper needs to be removed. First loosen the rear brake caliper mount bolts and remove them. Turn counter clockwise.
Step 3 - Lift Rear Brake Caliper from The Caliper Mount
rear_brake_pads_3.jpg After the caliper mount bolts have been removed, gently lift the brake caliper from the caliper mount. Inspect the caliper slides; they should move freely in the caliper mount. Remove rear brake pads and hardware.

Step 4 - Removing Caliper Mount Bolts
rear_brake_pads_4.jpg With a socket wrench or other appropriate removal tool, loosen the rear brake caliper mounting bolts. Remove bolts and lift the caliper mount and remove it from the vehicle. Remove the retaining screw from the disc mounting hole. Tap the rotor gently to release any rust that has accumulated between the rotor and bearing hub. Lift brake rotor from wheel hub holding on tightly, using both hands. You do not want to drop the rotor.

Step 5 - Removing Rear Brake Rotor
rear_brake_rotor.jpg Remove the retaining screw from the disc mounting hole, tap the rotor gently to release any rust that has accumulated between the rotor and bearing hub. Lift brake rotor from wheel hub, hold on using both hands and do not drop.

Step 6 - Install New Brake Rotor
rear_brake_rotor_2.jpg Check the new rotor against the old brake rotor to make sure they are the same size. Clean the mating surface on the wheel hub before the new brake rotor is installed. Reinstall rotor retainer screw.
Step 7 - Reset Rear Brake Caliper
rear_brakes_7.jpg Before new brake pads can be installed, the rear brake caliper must be reset. The reset tool winds the piston back into position so the new brake pads will fit. This style of brake caliper will not compress with a clamp tool; it can only be reset with the proper reset tool.
Step 8 - Reinstall Rear Caliper Mount and Install New Rear Brake Pads
rear_brake_rotor_3.jpg After the caliper has been reset, reinstall caliper mounting bolts and make sure the bolts are tight. Then match up the old brake pads to the new brake pads. They should be exactly the same except, of course; the old ones will be worn out. Check the new brake pads for proper fit and install any brake hardware that is required.
Step 9 - Remount Rear Brake Caliper
rear_brake_rotor_4.jpg Reinstall the brake caliper, align brake pad hardware and reinstall caliper mounting bolts. (Note: align the rear peg of the brake pad to the groove in the caliper piston.) Recheck and retighten all caliper and caliper mount bolts. Bleed brake system to relieve any air in the system. Before driving the vehicle, push the brake pedal down and let it up slowly. This operation forces the brake pads to travel to the brake rotors. DO NOT DRIVE VEHICLE until proper brake pedal operation resumes. When test driving vehicle listen for any unusual noises during the operation of the brakes.
WARNING! Always have the vehicle under inspection on level ground, in park with the emergency brake on. Always wear protective eyewear, gloves and necessary clothing before inspection or work begins. Never crank an engine over when anyone is near the battery or engine. Always have an operational fire extinguisher close by, obey all first aid instructions in the event of an injury. Never stand in front or behind a vehicle when cranked over or running. When engine is cranked over keep hands and clothing away from rotating components. Never move a car without proper brake pedal operation.

Jun 01, 2010 | 1995 Saab 900

1 Answer

I have a 2003 chevy avalanche, and i need to replace my rear brakes and need step by step instruction. I am not a mechanic but know a little. Please thank you


jack up the rear of the car remove wheels and tires, remove the two caliper bolts, remove old brake pads, using a c clamp push each piston the the caliper bake in install new pads, reinstall caliper install wheels and tires lower the jack and your done
caliper bolts are torque head bolts be sure to have the proper size before trying to change the brakes

Sep 27, 2009 | 2003 Chevrolet Avalanche

1 Answer

Rear brake lines


run new lines forget about removing old ones,the lines run above fuel tank to block on passenger side,run both lines to left and right rear wheels just make sure they don't interfere with any suspension parts

Aug 14, 2009 | 1997 Subaru Outback

1 Answer

How to replace rear brake pads on 2005 Jeep Liberty


put the back of car on jack stands and secure the front tires so it does not roll and then remove the bolts off the back of the caliper there is normally two one at top and one at bottom and spray it with some kind of oil for rust and make sure you have the right size socket before you try to loosen them and once caliper is off and the old pads removed take one of the old pads and squeeze the piston on the caliper back in by using a "C" clamp and also remove some of the brake fluid from the master cylinder before you do this put the new ones back on and check the brake fluid and make sure it is full and then pump the brakes to make sure you have a good pedal also put some "No Squeak" brake stop on the back of the pads so they don't squeak they will have that where you buy the pads from

Mar 01, 2009 | 2005 Jeep Liberty

1 Answer

Rear brakes


After removing tire pull bolts holding brake calipers to rotor. Use a clamp or something in that nature to push old brake shoe into housing that way you wont have to bleed your brake system. Replace new shoes and reinstall caliper. Start vehicle and pump up brakes before traveling make sure to test brakes first to make sure no fluid was lost.

Feb 15, 2009 | 2001 Dodge Ram 1500 Truck 2WD

2 Answers

REAR BRAKES


i think your aware of how to change the brakes if im right and your problem is the rusted drum doesnt want to come off the only way to get the old drum off is to remove adjuster plug from behind drum dustshield and adjust the shoes so that there not even close to the braking area of the drum then try and wiggle the drum off of the assembly if it is not coming off then you need to use the old nylon hammer on the drum and i mean you must hit the drum from side to side trying by hand to wiggle the drum off its a tight fit and you need to strike the drum on the face not on the fins not wanting to damage with persistance and care and patience you will eventually be able to remove the drum to service brakes take care and good luck with it

Jul 01, 2008 | 2007 Dodge Caliber SXT Sport Hatchback

Not finding what you are looking for?
1994 Toyota Celica Logo

Related Topics:

53 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...