Question about 2008 Hummer H3
I have the dvd monitors in the headrest of my 2006 h3 and they stopped working. Does it sound like a fuse or did something get unplugged under the seat. The nearest hummer dealer is 25miles away. Jim
I brought my 2006 H3 in to the dealer for the same thing. My blower stopped working all together but it started as an intermittent problem. He said he had to replaced a diode or resistor either behind the switch on the dash that controls the fan or on the fan motor itself. Have not had a problem since but that was only about 4 months ago.
Posted on Apr 09, 2009
If you look in the owner's manual it will explain this. Happened to me a bunch of times, really embarassing. It is an additional anti-theft device . If the computer senses that the key is inserted improperly, or that it is not a perfect match for the code it has in its memory for your key, it shuts of the gas supply to your engine for approx. 10 minutes to defer theft. Still happens to me intermittently. Now only very rarely. Total pain. I cleaned my key..carefully, with WD40 and after drying put just a touch of graphite on the key and started the beast a number of times. My dealer didn't read the manual either. You must wait the full ten minutes before trying to restart....otherwise it never totally resets and (the first time this happened to me) you can sit there and fight it forever.
I don't have my owner'smanual handy to refer you directly to the proper pages, but its in there under theft deterent. Hope this helps......and that Hummer can provide aneasy fix for this.
Posted on Jul 21, 2009
Probably too late now, I am sure you have already fixed it, but mine did this and it was an electrical part that is mounted right beside the blower fan. The part was OK, but the plug into the part was arcing and burned out the connection. A Chevy mechanic told me this has been happening to MANY Chevy products. I had to buy a new part and plug assembly with new wires, about 100 dollars, and I spliced them together. It was an Easy fix, but I shouldn't have had to do it :(
Posted on Mar 07, 2010
My 06 was leaking during rain also. It turned out to be the sunroof. There are two drain tubes in the front of the sunroof that run the water down the corners to the ground and two drain tubes that drain water out the back corners. The water would seep around the glass, which is expected, but both of the tubes on the front of mine were plugged, and the water would overflow behind the dash and fill my floorboards. If my H3 was leaning to the left during a storm then the drivers side would be full of water. If leaning right, then the passenger side. I had to open sunroof and blow compressed air into the drain holes to clear them, but be careful, too much air will separate tubes from sunroof and then you will have to remove the inside paneling around sunroof to get to tubes and reconnect. You may only have one side plugged. you can test it by opening sunroof and pour a little water in the small catch pan in the front of the sunroof and see if it drains as expected (to the ground under the firewall on left AND right side). You can see the holes in each corner of catch pan to drain the water. Plug one with your finger, then the other to find the plugged side. Good luck!! Hope this helps!!
Posted on Mar 07, 2010
SOURCE: 2006 H3 Hummer fan problem
Hi if your internal fan not work in any position well i fixed up myself easy and save your money.
locate the fan motor air just outside right courtesy drawn document in front of passenger. go from down and look up you will see a motor with a big connector white with 2 screw secure inside the motor block. loose the two screws and pull out gently the connector from motor fan block. you will see a green multiresistor connected with this big connector. Usually the first + voltage connector is burnet out. disconnect the connector pull from resistor and check for any burn. in my case the first pin was burned out completely
you can buy another connector or you can clean the burned connector take out form connector weld a small copper cable of 5 mm dia from resistor to the burn cable and reconnect the connector without buy a new one. after replace again the resistor in the hole of motor blow with the 2 screw.
Done all work again without buy another new connector.
Gabriel from Italy Turin
H3 hummer 2007
loveling one and Humvee owner
Posted on Jun 11, 2010
Tips for a great answer:
Nov 14, 2011 | 2006 Hummer H3
Aug 29, 2011 | 2006 Hummer H3
Feb 07, 2011 | 2006 Hummer H3
Feb 06, 2010 | 2006 Hummer H3
Dec 13, 2009 | 2008 Hummer H3
Sep 10, 2009 | 2006 Hummer H3
Jun 28, 2009 | 2006 Hummer H3
Feb 24, 2015 | 2008 Hummer H3
174 people viewed this question
Usually answered in minutes!