How do I remove the front and rear door sill cover plates on my 2004 Jaguar X-Type without breaking them?

remove the little screw cover on the interior door handle and screw next arm rest cover screw blanks and screws poss all torx screws you should next be able to remove panel using a clip remover or screwdriver to get panel off but more than likely the clips will break and you have to replace them

Same place you fill for the front washer fluid ! Your fronts work but not the rear ? There are to washer pump motors on the washer fluid bottle , one for the front an one for the back . Rubber hose goes all the way to the back . If that hose has failed ,to replace it you basically have to pull out your vehicles interior .
Rear Window Washer Hose Replacement - Pump to Endgate
Removal Procedure

1. Remove the left front seat. Refer to Bucket Seat Replacement in Seats.
2. Remove the rear seat. Refer to Rear Seat Replacement in Seats.
3. Remove the endgate/liftgate door sill plate. Refer to Rear Floor Rear Trim Plate Replacement or Liftgate Door Sill Plate Replacement in Interior Trim.
4. Remove the left front and left rear door sill plates. Refer to Door Sill Plate Replacement in Interior Trim.
5. Remove the left body side trim panel. Refer to Body Side Trim Panel Replacement in Interior Trim.
6. Remove the left hinge pillar trim panel. Refer to Body Hinge Pillar Trim Panel Replacement - Left Side in Interior Trim.
7. Fold over the left side of the carpet to allow access to the body harness. Refer to Front Floor Mat/Carpet Replacement and Rear Floor Panel Carpet Replacement in Interior Trim.

Disconnect the washer hose connection (1) from the body harness (2) at the endgate. Remove the air cleaner assembly. Refer to Air Cleaner Assembly Replacement in Engine Controls.
Disconnect the hose (1) from the rear washer pump. Install a plug to the rear washer pump nozzle to prevent washer fluid loss. Push the hose grommet (2) in through the bulkhead.
Pull the washer hose (1) into the vehicle though the bulkhead. Cut the old washer hose off where it enters the body wiring harness (2). Remove the hose end from the vehicle
Or it could be the pump , they go bad . switch the hoses from one pump to the other an see if you get washer fluid at the back ,if you do the pump is bad ,if not the hose or the spray nozzle is clogged . You probably will need to pull the washer fluid bottle to see both pumps

It is located behind the right rear quarter panel , In the back right of the interior !
Remove the right rear quarter trim panel. Refer to Rear Quarter Trim Panel Replacement - Right Side in Interior Trim.
Removal Procedure

1. Remove the rear seat. Refer to Rear Number 2 Seat Replacement or Rear Number 2 50-50 Seat Replacement in Seats.
2. Remove the Third Pillar trim panel. Refer to Third Pillar Trim Replacement .
3. Remove the garnish molding. Refer to Body Rear Corner Garnish Molding Replacement .
4. Remove the door sill plate. Refer to Liftgate Door Sill Plate Replacement .
5. Remove the quarter panel trim screws.

A lot involved in this but not to difficult !

1. Remove the rear door sill trim plate. Refer to Front Side Door Sill Plate Replacement or to Rear Side Door Sill Plate Replacement .
2. Remove the lower rear seat belt cover and bolt.
3. Remove the trim panel from the vehicle.

Remove the sill plate. Firmly pull the sill plate up and out from the retainers.
Remove the sill plate from the vehicle. Start from the front of the door sill. Use a flat-bladed tool in order to pry the door sill plate.
Rear Side Door Sill Trim Plate Replacement
Use a flat-bladed tool in order to pry the door sill plate. Remove the sill plate from the vehicle.
Body Rear Corner Garnish Molding Replacement
Remove the rear upper garnish molding. Refer to Rear Upper Garnish Molding Replacement .
Pull down on the upper corners of the garnish molding in order to disengage the retaining clips. Pull in order to disengage the remaining retaining clips. Remove the rear corner garnish molding from the vehicle. Inspect the rear corner garnish molding for broken or missing retaining clips. Replace the retaining clips as needed.
Good Luck ! Fun job !!!!!

The windshield metal post from the roof to the bottom
of the door sill is called an A -pillar
That is what your door hinges are bolted to

The metal to your right as you enter the vehicle is
called the B-pillar
That is the one with the drivers door catch

The roof down to the door sill on the rear door of a car
or rear window downward is called a C-pillar

You may hear those terms if you watch a NASCAR race

The door sills are the metal sometimes covered with plastic
you swing your feet over to get in at the bottom between A & B
pillar

You may see rubber or some type covering just past the hinges
as you look into the front fenders

Inside next to the driver or passengers feet ,on the inside,
are what is called kick panels,inside sheet metal on A Pillars

Sounds like you may have anouther problem, the horn should only 'peep' if you have left something open, like the boot (trunk), a rear door etc. In normal circustances the horn should not sound.

from autozone.com:

Removal & Installation

1. Disconnect and isolate the negative battery cable.
2. Remove the right quarter trim panel as follows:
   1. Remove first rear seat. Remove the second rear seat, if equipped.
   2. Remove the sliding door sill plate.
   3. Remove the quarter trim bolster.
   4. Remove the upper C-pillar trim and D-pillar trim panel.
   5. Remove the first and second rear seat belt anchors.
   6. Remove the screws securing the quarter trim to quarter panel from the bolster area.
   7. Remove the screws securing the rear edge of the quarter trim to the support bracket.
   8. Carefully disengage the hidden clips securing the front of the quarter trim to the quarter panel just rearward of the sliding door opening.

   
   

Fig. Removing the trim panel to access the rear blower motor

i. Disconnect the wiring harness connector from the accessory power outlet, if equipped.

j. On long wheelbase wagons only, remove the quarter trim from the quarter panel and pull second rear seat belt through access hole.

k. Pull first rear seat belt through the access hole.

l. Remove the quarter trim panel from the vehicle.

3. Remove the 5 screws mounting the A/C-heater blower motor housing to the rear HVAC unit (one mounting screw located on evaporator cover).

4. Twist the blower motor out of scroll housing.

5. Disconnect the blower motor wiring connector.

6. Remove the blower motor from vehicle.


Fig. The rear blower motor is held in place by four screws
To install:

1. Install the blower motor unit into the vehicle.
2. Reconnect the blower motor wiring connector.
3. Secure the blower motor into scroll housing.
4. Install and tighten the 5 screws mounting the A/C-heater blower motor housing to the rear HVAC unit (one mounting screw located on evaporator cover).
5. Install the right quarter trim panel as follows:
   1. Install the quarter trim panel in position in the vehicle.
   2. Insert and pull the first rear seat belt through the access hole in quarter trim panel.
   3. On long wheelbase wagons only, insert and pull the second rear seat belt through access hole in quarter trim panel.
   4. Reconnect the wiring harness connector to the accessory power outlet, if equipped.
   5. Engage the hidden clips to secure the front of quarter trim to quarter panel rearward of sliding door opening.
   6. Install the retaining screws that secure the rear edge of quarter trim to support bracket.
   7. Install the retaining screws that secure the quarter trim to the quarter panel in bolster area.
   8. Install the second rear seat belt anchor (if equipped), and the first rear seat belt anchor.
   9. Install the D-pillar trim panel and upper C-pillar trim.
   10. Install the quarter trim bolster.
   11. Install the sliding door sill plate.
   12. Install the second rear seat, if equipped, and install the first rear seat.
       
6. Reconnect the negative battery cable. Check blower motor operation.

Removal & Installation

1. Disconnect and isolate the negative battery cable.
2. Remove the right quarter trim panel as follows:
   1. Remove first rear seat. Remove the second rear seat, if equipped.
   2. Remove the sliding door sill plate.
   3. Remove the quarter trim bolster.
   4. Remove the upper C-pillar trim and D-pillar trim panel.
   5. Remove the first and second rear seat belt anchors.
   6. Remove the screws securing the quarter trim to quarter panel from the bolster area.
   7. Remove the screws securing the rear edge of the quarter trim to the support bracket.
   8. Carefully disengage the hidden clips securing the front of the quarter trim to the quarter panel just rearward of the sliding door opening.
      
      
      

      Fig. Removing the trim panel to access the rear blower motor
      

   9. Disconnect the wiring harness connector from the accessory power outlet, if equipped.
   10. On long wheelbase wagons only, remove the quarter trim from the quarter panel and pull second rear seat belt through access hole.
   11. Pull first rear seat belt through the access hole.
   12. Remove the quarter trim panel from the vehicle.
       
3. Remove the 5 screws mounting the A/C-heater blower motor housing to the rear HVAC unit (one mounting screw located on evaporator cover).
4. Twist the blower motor out of scroll housing.
5. Disconnect the blower motor wiring connector.
6. Remove the blower motor from vehicle.
   
   
   

   Fig. The rear blower motor is held in place by four screws
   

To install:

1. Install the blower motor unit into the vehicle.
2. Reconnect the blower motor wiring connector.
3. Secure the blower motor into scroll housing.
4. Install and tighten the 5 screws mounting the A/C-heater blower motor housing to the rear HVAC unit (one mounting screw located on evaporator cover).
5. Install the right quarter trim panel as follows:
   1. Install the quarter trim panel in position in the vehicle.
   2. Insert and pull the first rear seat belt through the access hole in quarter trim panel.
   3. On long wheelbase wagons only, insert and pull the second rear seat belt through access hole in quarter trim panel.
   4. Reconnect the wiring harness connector to the accessory power outlet, if equipped.
   5. Engage the hidden clips to secure the front of quarter trim to quarter panel rearward of sliding door opening.
   6. Install the retaining screws that secure the rear edge of quarter trim to support bracket.
   7. Install the retaining screws that secure the quarter trim to the quarter panel in bolster area.
   8. Install the second rear seat belt anchor (if equipped), and the first rear seat belt anchor.
   9. Install the D-pillar trim panel and upper C-pillar trim.
   10. Install the quarter trim bolster.
   11. Install the sliding door sill plate.
   12. Install the second rear seat, if equipped, and install the first rear seat.
       
6. Reconnect the negative battery cable. Check blower motor operation.

Hope helps (remember to rate this).

here's 1996, all I have. Please rate.

Mirror, Power — Outside Rear View NOTE: This procedure applies to both RH and LH power outside rear view mirrors.

Removal

1. Remove the front door trim panel (23942). Refer to Section 01-05 for the removal procedure.
   

1. Remove the two outside rear view mirror inside mounting hole cover screws and the outside rear view mirror mounting hole cover (17K709) from the front door (20124).
   
   
   
   
   

1. Remove the wire clip.
   

1. Disconnect the power outside rear view mirror electrical connector.
   
   
   
   
   

1. Remove the three power outside rear view mirror bolts and the power outside rear view mirror.
   
   
   
   
   

Installation
To install, reverse the removal procedure. Tighten the three power outside rear view mirror bolts to 3-4 Nm (27-35 lb-in). Glass, Outside Mirror
Removal and Installation
Refer to the glass replacement procedures in Manual Mirror for power outside rear view mirror glass (17K707) Trim Cover
Removal

1. Remove the front door trim panel. Refer to Section 01-05 for the removal procedure.
   

1. Remove the two outside rear view mirror inside mounting hole cover screws.
   
   
   Remove the outside rear view mirror mounting hole cover.

Installation
To install, reverse the removal procedure. Mirror Control
Removal

1. Use a small flat-blade screwdriver to pry the power outside rear view mirror control switch from the instrument panel (04320).
   
   
   

first you go to local book store or dealer or ebay and pick up a chilton or haynes book it will come in handy for the wiring and the hinge torque and allinment specs and tricks

The rear door panels are not like the front doors ( additional panel on the door panel ), the silver/gray rear speaker panel is part of the rear door panel.

Remove the panels next to the window ( should be spring clips ).
This should expose 3 bolts holding the top of the door panel on.

Next remove the rear window console panel ( spring clips on the side towards the cab, tabs on the side towards the door ).
Behind this should be a bolt.
Next remove the rectangle cover in teh door handle area, there is a bolt behind this.
should be 1 other screw at the bottom of the door panel, by the door sill area ( under the map pocket ).
The door is held on like the front doors, with large plastic hooks, so pick up on the door panel once all the screws are out.