Question about 2005 Ford Escape

1 Answer

2002 ford escape passanger side headlamp assembly removal?

Has water in it. i have a new one do i need to remove the bumper for this fix?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Ford Master
  • 783 Answers

Removal and Installation

  1. NOTE: Make sure that the headlamp switch and the ignition switch are in the OFF position.
    Remove the front bumper cover. For additional information, refer to Section 501-19.
  1. NOTE: Pull headlamp assembly forward to access electrical connectors.
    Remove the headlamp assembly.
    1. Remove the three bolts.
    1. Loosen the nut.
    • Disconnect the electrical connectors.
    2002 ford escape passanger side headlamp assembly  - a0045726.gif
  1. To install, reverse the removal procedure.
    • If necessary, adjust the headlamps. For additional information, refer to Headlamp Adjustment in this section.

Posted on Mar 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I change the headlight housing on my 1999 lumina


Raise the hood.
Lift the flap on the appropriate end of the radiator upper air deflector.
Separate the radiator side air baffle from the upper air deflector.
Remove the fastener retaining the upper edge of the front bumper fascia to the headlamp bracket.
Remove the two bolts retaining the headlamp assembly to the headlamp bracket.
Slide the headlamp assembly slightly inboard to release the outboard retaining tabs. Carefully pull the upper edge of the front bumper fascia away from the inboard edge of the headlamp assembly enough to aid in headlamp removal. Carefully remove the headlamp assembly from headlamp bracket.

Nov 22, 2014 | 1999 Chevrolet Lumina

1 Answer

How to remove headlamp assembly 2006 Ford Five Hundred


bulb replacement?

You may be able to clear bumper cover by pusihing down while pulling out lamp.

Please rate.
---------------------------

SECTION 417-01: Exterior Lighting 2005 Freestyle/Five Hundred/Montego Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 03/14/2005
Headlamp Assembly - Five Hundred, Montego adobe.gif Printable View (211 KB) n0050703.jpg
Item Part Number Description 1 W702706 Top headlamp assembly bolts (2 required) 2 W704551 Side headlamp assembly bolt 3 W702706 Front headlamp assembly bolt 4 13005/13006 Headlamp assembly (RH/LH)
Removal
  1. Remove the front bumper cover. For additional information, refer to Section 501-19.
  1. Remove the 4 bolts and the headlamp assembly.
    • Disconnect the electrical connectors.
Installation
  1. Connect the electrical connectors and position the headlamp assembly in place.
  1. Install the side headlamp assembly bolt.
    • Tighten to 11 Nm (8 lb-ft).
  1. Install the front headlamp assembly bolt.
  1. Install the top outboard headlamp assembly bolt.
  1. Install the top inboard headlamp assembly bolt.
  1. Install the front bumper cover. For additional information, refer to Section 501-19.

Aug 03, 2011 | Ford Five Hundred Cars & Trucks

1 Answer

I have a 2002 escape and want to replace the right front headlight. Do you know if the bumper needs to be removed to install light?


When you look at it from the top down you should see 2 adjustment screws. Remove those and the headlight assembly should come out.

Jan 30, 2011 | 2002 Ford Escape

1 Answer

Need to replace the headlight assembly on front passenger side do i have to take off the bumper? for ponitac vibe 2003 also have dent on the area


Yes you do. This is the steps to do that to replace the entire headlight assembly:


Remove the front fascia.
  • Remove the front fascia extensions, if equipped.
  • Remove the front fender liners.
  • Remove the fog lamps.
  • Remove the bolts (4) from the front bumper fascia (3) at the fender.


506bafd.gif

Remove the bolts from the front bumper fascia at the fender



  • Remove the push-in retainers (2) from the bumper fascia using J38778.
  • Remove the fascia bolts (1) from the fascia.
  • Remove the fascia from the vehicle.
  • Remove the 3 bolts which secure the composite headlamp.


  • 7f1ec16.gif

    Remove the 3 bolts which secure the composite headlamp



    1. Remove the sidemarker bulb electrical connector.
    2. Remove the sidemarker bulb, if necessary.
    3. Remove the composite headlamp assembly from vehicle.

    To install:

    1. Install the sidemarker bulb to the composite headlamp, if removed.
    2. Connect the sidemarker bulb electrical connector.
    3. Secure the composite headlamp to the vehicle with the 3 bolts. Tighten the headlamp mounting bolts to 89 inch lbs. (10 Nm).
    4. Install the front fascia.
    5. Install the headlamp bulb to the composite headlamp, if removed.
    6. Fasten the headlamp bulb retainer clip.
    7. Install the socket to the headlamp bulb.
    8. Install the rubber cover to the composite headlamp.
    9. Aim the headlamps.
    10. Close the hood.

    Oct 12, 2010 | 2003 Pontiac Vibe

    1 Answer

    Replacing the hole headlight


    SECTION 417-01: Exterior Lighting 2002 Lincoln LS Workshop Manual REMOVAL AND INSTALLATION Lamp Assembly —Headlamp Removal and Installation
    s2x~us~en~file=ani_caut.gif~gen~ref.gif WARNING: The halogen fog lamp bulb contains gas under pressure. The bulb may shatter if the glass envelope is scratched or if the bulb is dropped. Handle the bulb only by its base. Avoid touching the glass envelope.
    NOTE: The headlamp bulb should not be removed from the headlamp assembly until just before a replacement bulb is installed. Removing the bolt for an extended period of time may affect headlamp bulb performance. Contaminants may enter the headlamp assembly where they can settle on the lens and reflector. Never turn on the headlamps with the bulb removed.
    1. NOTE: Make sure that the headlamp switch and the ignition switch are in the OFF position.
      Release the ambient air temperature sensor.
    1. Remove the radiator grille opening cover at the top shelf of the bumper.

    1. Remove the radiator upper sight shield.
      1. Remove the pin-type retainers.
      1. Remove the radiator upper sight shield.
    1. Position the headlamp assembly for removal.
      1. Remove the three bolts.
      1. Position the headlamp assembly for removal.
      • Disconnect the electrical connectors and remove the headlamp assembly.
    1. To install, reverse the removal procedure.
      • If necessary, install new bulbs.
      • c13635b.gif

    Feb 27, 2010 | 2002 Lincoln LS

    1 Answer

    I need info on how to replace the headlamp bulbs on my 2008 Chevy Malibu, can you help.


    The procedure is very involved.It requires the removal of the front bumper fascia fasteners from the center and side of the headlamp to be removed.
    1. Remove the front bumper fascia fasteners from the center and side of the headlamp to be removed, full removal of the fascia is not necessary. Refer to Front Bumper Fascia Replacement.
    2. Gently pull the fascia forward to allow clearance to remove the headlamp assembly.
    3. You will also need to remove some of the fasteners at the front of the inner wheel well.
    4. The Front Bumper Fascia is the plastic cover over your front bumper.
    5. You may also have to remove the plastic cover that is located under the front of the hood over the radiator.It extends to both sides.

    Oct 27, 2009 | 2008 Chevrolet Malibu

    1 Answer

    Replace 1998 chevy lumina headlight assembly


    Here are the steps:

    1. Raise the hood.
    2. Lift the flap on the appropriate end of the radiator upper air deflector.
    3. Separate the radiator side air baffle from the upper air deflector.
    4. Remove the fastener retaining the upper edge of the front bumper fascia to the headlamp bracket.
    5. Remove the two bolts retaining the headlamp assembly to the headlamp bracket.
    6. Slide the headlamp assembly slightly inboard to release the outboard retaining tabs.
    7. Carefully pull the upper edge of the front bumper fascia away from the inboard edge of the headlamp assembly, just enough to aid in headlamp removal.
    8. Carefully remove the headlamp assembly from the headlamp bracket.
    9. Disconnect the electrical connectors from the headlamp bulbs.
    10. Rotate the park/turn signal lamp socket counterclockwise to release.
    11. Remove the headlamp assembly.

    Sep 06, 2009 | 1998 Chevrolet Lumina

    2 Answers

    Need to replace head lamps on Ford Escape 2001,


    there are 4 bolts that hold lamp in. the first 2 are obious. the others are behind the front bumper..the bumper must be removed to expose them...here is a cpoy of the manual to change..good luck

    Headlamp Assembly Removal and Installation
    1. NOTE: Make sure that the headlamp switch and the ignition switch are in the OFF position.
      Remove the front bumper cover. For additional information, refer to Section 501-19.
    1. NOTE: Pull headlamp assembly forward to access electrical connectors.
      Remove the headlamp assembly.
      1. Remove the three bolts.
      1. Loosen the nut.
      • Disconnect the electrical connectors.
      a0045726.gif
    1. To install, reverse the removal procedure.
      • If necessary, adjust the headlamps. For additional information, refer to Headlamp Adjustment in this section.

    Apr 22, 2009 | 2003 Ford Escape

    1 Answer

    Looking for directions on how to replace the main headlamp on 2002 pontiac grand prix. Buld comes out the back but no access. Looking for typical approach. Please advise


    You need to remove the entire headlamp assembly. There are a couple of screws on the top that hold it tight that have to be removed. After you remove the screws the assembly will be loose, but still held in place by a plastic tab towards the outside of the assembly. You just need to pull the assembly out. It may not come out easily. One side of mine came out easily, the other side I had to tug and pull pretty hard. After you replace the bulb you need to slide and push the assembly back in place. The tab needs to go in first. You will know when it is in place correctly when there about a half inch gap between the assembly and the bumper. If the assembly rests on the bumper you do not have it in correctly. Replace the screws on the top.

    Mar 07, 2009 | 2002 Pontiac Grand Prix

    2 Answers

    Need to replace headlight assembly on 2005 Ford Escape


    ithere are 4 bolts that hold it in...the top 2 are obvious..the others are behind the bumper. the bumper must be removed to acces them...here are the manuals instructions..

    n0037234.gif
    Item Part Number Description 1 — Headlamp assembly bolts (3 required) 2 — Headlamp assembly nut 3 13008 Headlamp assembly 4 14290 Electrical connectors
    Removal and Installation
    NOTE: Make sure the headlamp switch and the ignition switch are in the OFF position.
    1. Remove the front bumper cover. For additional information, refer to Section 501-19.
    1. Remove the 3 headlamp assembly bolts.
      • To install, tighten to 5 Nm (44 lb-in).
    1. Remove the headlamp assembly nut and the headlamp assembly.
      • Disconnect the electrical connectors.
      • To install, tighten to 5 Nm (44 lb-in).
    1. To install, reverse the removal procedure.

    Jan 01, 2009 | 2005 Ford Escape

    Not finding what you are looking for?
    2005 Ford Escape Logo

    277 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Ford Experts

    yadayada
    yadayada

    Level 3 Expert

    61249 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    21949 Answers

    Fordexpert

    Level 3 Expert

    5331 Answers

    Are you a Ford Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...