Question about 2000 GMC Sierra

1 Answer

Abs light stays on even after all the brakes were completely done all rotors pads fluid emerg cables

Posted by on

  • mike loshbough
    mike loshbough May 11, 2010

    there is a abs sensor problem

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 740 Answers

Have to put this vehicle on a computer, It sounds like a bad ABS sensor or something like that, can guess. I would recommend auto zone they will check for free. Good luck and Thanks for using FIX YA

Posted on Mar 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have had new non Nissan rotors and brake pads installed as well as new tyres and now the VDC light won't go off. Brake fluid level is fine. Any ideas for what best action is. Thanks


check the switch make sure its on ---check brake fluid level --- the wiring to the abs make sure no damage or disconnection when brakes/rotors were done ---recheck brake pads if not seated right known to throw codes ---

Jun 09, 2016 | 2006 Nissan Pathfinder

1 Answer

Abs light stays on and abs system does the same


Try adding brake fluid to the reservoir that should put the light to rest if not when have you had the brakes serviced last, if you start to hear a metal rubbing noise waste no time to get the brakes serviced chances are you need pads or shoes.. Every 25,000 to 30,000 miles should have them inspected other wise you risk rotor or drum damage if the pads or shoes wear down too far.. hope this helps..

Dec 25, 2014 | 1999 Lexus Gs 400

1 Answer

Ford taurus 1996 3.0 ABS ligth on


Hello, These warning lights are pretty accurate. Autozone, Advance, and Oreillys give free scans although the engine system and brake system can require different scanners.

Check your brake fluid level first. The ABS system requires sensors which require counting the revolutions of each wheel. Sometimes the sensors may break, but they can be blinded by dust and debris.

If you have a broken brake pad, the warning light can come on. Often the Emergency brake pad, inside the rear Rotor, can fall apart and trigger an ABS warning.

You need to inspect both the front and rear brakes or take your car to a brake shop for evaluation. Sometimes you can get a free estimate, and some shops can charge for inspecting the Emergency brakes because of the work needed to reach them.

Jul 07, 2011 | 1996 Ford Taurus

1 Answer

Abs light stays on what does that mean? 93 grand marquis


This means you have something worn out in the brakes. It is usually an accurate indicator. You could be low on Brake fluid, but then something is leaking and that is not good.

You need to check the Brake pads, Rotors, and take off the rear Rotors to check the Emergency brakes. Remember to clean the debris off all the sensors you see with Electrical wires on them. Remember to tell the Brake place if you have someone work on it, that you want the Emergency brakes checked.

I have had some clients go to both a Dealer and a Brake place and both places failed to find the bad Emergency brakes.

Jun 14, 2010 | 1993 Mercury Grand Marquis

1 Answer

2002 ram 1500 brake and abs light on


there should be adjustment under vehicle looks like bolt attached to cable just back off nut and loosen bolt 

Oct 06, 2009 | 2002 Dodge Caravan

1 Answer

The abs and emergency brake light come on periodically


This usually means its time to get your brakes changed. It also happens when your running low on brake fluid. It might not be low enough to stay on, but when the road gets rough the fluid is moving around enough to trigger your light. Also make sure your E brake is all the off. It might be close enough to the switch that vibration is causing it to make contact flashing your light. If you experience this during heavy braking then your running low on both fluid and maybe even pads.

Aug 01, 2009 | 2001 Chevrolet Silverado 1500

2 Answers

ABS alarming after I replaced rear brakes shims, bled brakes etc.


make sure that the abs connect for that side is connect properly and the right amount of brake fluid is there

Jul 01, 2009 | 2003 Toyota 4Runner

1 Answer

Abs light stays on


I had this exact same problem, on a older bronco II. You need to get the ABS computer reset. You can either take it in or buy a computer your self. There are even packages that will allow you to use your own computer and just hook the car up to your lap top or desk top if you can get a cable long enough.

I never had mine done, because back then the computers were so expensive. I never caused a problem because it was only in the braking system. Now they are pretty cheap and there are a lot of other cool things you can do with them. You can reduce your gas requirements and set it for pulling, racing, and fuel efficency on the fly now. Just at the touch of a button.

tepfy

Jan 20, 2009 | 2002 Lincoln LS

Not finding what you are looking for?
2000 GMC Sierra Logo

229 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...