Question about 1999 Dodge Durango

1 Answer

WHERE IS THE CRANK SHAFT SENOR?

I HAVE A 99 DODGE DURANGO, WHERE IS THE CRANK SHAFT SENOR AND DO I HAVE TO RESET THE TIMING?

Posted by on

  • Rob
    Rob May 11, 2010

    Under the harmonic balancer?

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 56 Answers

The crank sensor is located on the trans. bell housing.Look behind the engine where the tranny bolts to the block and on top of the bell housing just a little off center you will see the sensor which has 2 bolts mounting it in place.It has a 6in length of wire attached to it with a plug on the end.This sensor reads off the flywheel.Hope this helps.

Posted on Mar 03, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2004 Dodge Durango 4.7 liter started then just stopped will crank could be fuel line freeze up.Also told could be Cam shaft senor Crank shaft sensor had check engine light on did OBD said EVAP Leak


Suggest before you start to replace parts See what is missing , fuel or spark . Evap leak has nothing to do with it . Videos on youtube testing spark and fuel pressure . special tools needed . You probably would be better off just taking it to a qualified repair shop that has all the tools . Probably know in less then an hour what's wrong .

Jan 08, 2017 | 2004 Dodge Durango

3 Answers

Will a bad pick up coil stop a 1999 dodge Durango from cranking


It wouldn't stop the engine from turning over while trying to start. But it can make engine not start or run poorly

Sep 12, 2015 | Dodge Cars & Trucks

1 Answer

2001 Durango. Why won't it start?


I would closely check the wiring to make sure that the connector for the senor has not dislodged, it happens. Also if you have an OBD reader, the computer would tell you what is wrong.

Jun 07, 2015 | 2001 Dodge Durango

1 Answer

How do I locate the Crank shaft sensor on a 2005 Dodge Durango


Have you looked on the transmission just behind the engine block? A lot of the Dodge vehicles get readings of the flexplate/flywheel.

Sep 12, 2014 | 2005 Dodge Durango

1 Answer

HOW TO CHANGE 1998 DODGE DURANGO SPEED SENSOR


i had the same problem on my 99. the senor is located in the rear differential on top. speed was off, doors would not lock at speed,(15 mph) mileage comp was off, etc. sensor fixed all. good luck

Aug 11, 2012 | 1998 Dodge Durango

1 Answer

My 1998 Dodge Durango won't start. No spark


check for power at the coil. There should be power anytime the engine is cranking. If there is no power let me know and i'll get you some more info.

If there is power check for pulse on the other wire. If there is pulse than replace the coil.

if there is no pulse I can get you more info on that as well.

Feb 08, 2012 | 1998 Dodge Durango

2 Answers

99 dodge durango keeps shuttin down every so often cleaned battery cables and replaced clamps on both terminals worked for a day then same thing and security light will come on if i unhook pos cable and...


2002 Durango shuts down without warning. Sit for about 30-45 min and will restart, run for a while, and shut down again. Shows "NO BUS" code. Took it to Dodge Dealer and had a diagnostic done....nothing!!! Have changed PCM, crank shaft sensor and am getting ready to RUN IT OFF A CLIFF if I can get it running long enough!!! It is a black hole and we are getting no where!! I can't even sell the dang thing!!

Aug 14, 2009 | 1999 Dodge Durango

1 Answer

Crank shaft sensor. where is it located on a


behind the engine on the top passenger side of the engine. 2 13mm. bolts.goes through the bell housing.

Mar 29, 2009 | 2000 Dodge Durango

2 Answers

Crank shaft senor


First be sure it is the crankshaft sensor. by getting a trouble code. at Autozone or other store.
The crankshaft sensor is usually located near the timing belt cover. If not , it can be inside the cover in some cars. No, the ECU will recognize the sensor . There is no need to move the timing. If there is any trouble after installing a new sensor.
With the key turnd off, remove the negative cable and reinstall it after a minute.

Mar 02, 2009 | 1999 Dodge Durango

4 Answers

Crank sensor location 1999 dodge durango


the crank sensor is located passenger side back of the engine were the trans and engine come together .there are 2 - 13mm.bolts that bolt to top of the engine.

Feb 22, 2009 | 1999 Dodge Durango

Not finding what you are looking for?
1999 Dodge Durango Logo

Related Topics:

297 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

68038 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22011 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6817 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...