Question about 2002 Ford F250 Super Duty SuperCab

1 Answer

Turn signal light

Has rear stop light when apply and light turn on when the light switch is on. Also the flashes don't flashes and no indication on dash board to be on; nor blinking

Posted by on

  • James Sledge
    James Sledge May 11, 2010

    Please clarify your problem, was unable to understand the problem your having.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 101 Answers

Check the flasher that may be faulty hope this helps

Posted on Mar 03, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The hazard back lights wont quit blinking when car is running even when i pull the fuse on a 2002 buick regal


What fuse are you pulling ?

Hazard Lamps
The hazard warning switch is part of the turn signal switch. The turn signal switch receives battery voltage at all times through the HAZARD SWITCH Fuse. When the hazard switch is placed in the HAZARD position, battery voltage is applied to the hazard lamp/turn signal lamp flasher. The hazard lamp/turn signal lamp flasher sends a turn signal flasher signal to the turn signal switch. The turn signal switch provides all of the turn lamps and turn indicators with the turn signal flasher signal, simultaneously flashing them on and off.

Turn Signal Lamps
The front turn signal lamps are made up of the front park/turn signal lamps and rear turn signal lamps. The front turn signal lamps flash with the rear turn signal lamps when a turn is initiated using the turn signal/multifunction lever. The turn signals will operate only with the ignition switch in the RUN position and will not operate during hazard flasher operation.
When the ignition is turned to the RUN position, battery voltage is supplied to the TURN SIGNAL Fuse. Battery voltage is then applied through the turn signal fuse circuit to the turn signal switch. When the turn signal switch is placed in the LH or RH position, voltage is supplied to the hazard lamp/turn signal lamp flasher. The hazard lamp/turn signal lamp flasher supplies a turn signal flasher signal to the turn signal switch. With the turn signal switch in the LH or RH position the corresponding turn signal indicator, rear turn signal, and front turn signal receive the turn signal switch signal and will flash. The front turn signals receive the turn signal switch signal from the turn signal switch via the BCM. The turn lamps are permanently grounded.

Replace the turn signal switch. Refer to Multifunction, Turn Signal, and Hazard Switch Replacement - On Vehicle in Steering Wheel and Column - Tilt.

Feb 11, 2017 | Buick Cars & Trucks

1 Answer

I'm needing the wiring diagram for my 2007 Chevrolet Impala LT 3.5 tail lights.


Go to http://www.bbbind.com/free_tsb.html free wiring diagrams ! You having tail light problems ? Do you know how they work ?

They are turned on by the BCM !
Park, Tail, Marker and License Lamps
The park, tail, license, and marker lamps are turned ON when the headlamp switch is placed in either the HEAD or PARK lamp positions, or anytime the automatic light control (ALC) turns the headlamps ON. When the headlamp switch is placed in the park lamp or headlamp positions, ground from G202 is applied through the signal circuit to the BCM indicating the park lamp request. In response to this signal, the BCM applies ground through the park lamp relay control circuit energizing the PARK LP PCB Relay. With the relay energized, battery voltage is applied through the switch side of the relay, both park lamp fuses, and the supply voltage circuits illuminating the park, tail marker, and license lamps. Ground for the left front park and marker lamps is provided at G101 and the right front park and marker lamps at G100. Ground for all rear lamps is provided at G302.
Turn Signal Lamps
The LT T/SIG and RT T/SIG fuses located in the underhood fuse block supplies battery positive voltage to the body control module (BCM) for turn signal and hazard lamp operation. When the turn signal switch is place in either the LEFT or RIGHT position, ground from G202 is applied through the turn signal switch signal circuit to the BCM indicating the turn signal request. In response to this signal, the BCM applies a pulsating voltage to the front and rear turn signal lamps supply voltage circuits cycling the lamps ON and OFF. The BCM also sends a message via GMLAN to the instrument panel cluster (IPC) to cycle the turn signal indicator ON and OFF depending on the position of the turn signal switch.
Ground for the turn signal lamps is supplied as follows:
?€¢
G101 provides ground for the left front turn signal lamp


?€¢
G100 provides ground for the right front turn signal lamp


?€¢
G302 provides ground for the left and right rear turn signal lamps

May 03, 2016 | 2007 Chevrolet Chevrolet Impala LT

1 Answer

My signal lights in my dash both light up when i apply the breaks and only works when i let go of the breaks


Usually this is a short in one of the sockets that holds the bulb, your brake lights are back feeding power causing your turn indicators to glow on dash when you hit the brakes and will stop the turn signal from flashing when you step on the brake pedal also. Start with sockets on rear and look for any shorted or blackened socket ends.

Jan 20, 2014 | 2000 Toyota Avalon

1 Answer

2005 Suburban brake signal light issue


Sounds like a faulty turn signal switch. The brake light wire is routed through the turn switch, so it appears the turn switch has gone crazy.

Dec 27, 2013 | 2005 Chevrolet Suburban 1500

2 Answers

1991 Nissan Pathfinder left turn signal comes on when I apply the brake


check that all your bulbs are correct and are making contact. this commonly happens when a wrong bulb is installed in a socket. the other reason this happens is a bad ground, and one bulb uses another as a ground path. I would start at the rear left light and check that everything is good there, then move on to the front. 99 percent of these kinds of problems are at the lights themselves.

Mar 21, 2013 | Cars & Trucks

1 Answer

My dashboard and rear lights don't work


Assuming this has the V6, the 15A PARK LPS fuse in the underhood fuse block feeds constant power to the auto park lamp relay. When the relay closes, 12V power passes through the 10A INST LPS fuse in the right instrument panel fuse block to the panel dimmer switch and then to the five instrument cluster lamps.

If by "rear lights" you mean everything in the rear lamp assemblies, power for the tail lights (running lights) starts at the 15A PARKLAMP fuse in the underhood junction block, passes through the automatic lamp control (ALC) relay and the right instrument panel junction block to the tail filament of the dual stop/tail lamp and the separate tail lamp on each side. The 12 V power for the stop lamps is protected by the 20A STOPLAMPS fuse in the left I/P junction block, passes through the stoplamp switch when brakes are applied, stop filament of the dual stop/tail lamps. That leaves the turn signals and the hazard lamps. Power for the turn signals originates at the 10A TURNLAMPS fuse in the left I/P junction block and is applied to the hazard switch. Switch output goes to the turn/headlamp/wiper switch for selection of left or right turn signals. That switch output goes to the turn lamp. Power for the hazard function begins at the 10A HAZRD LPS fuse in the left I/P junction box and goes to the hazard switch. Switch output is sent to the left I/P junction box to make the turn signals flash. That's it. Post a comment if you need more information.

Sep 15, 2012 | 2002 Oldsmobile Alero

1 Answer

1999 oldsmobile aurora side marker light flash on and off when the car is turned off


Power is appliedat all times through the 20A HZRD/ STOP LPS fuse in the right rear junction block. The ORG wire connects to the hazard flasher and the BRN output wire connects to the A5 terminal of the TURN/HAZARD switch assembly. When the HAZARD switch is engaged, power is applied to the front and rear turn signals and the left and right turn indicators in the instrument cluster, causing them to flash. Obviously an open fuse, a defective flasher, a defective HAZARD switch, or a defective TURN/HAZARD switch assembly will prevent the lamps from flashing. If the turn signals operate normally, they are not the problem.

Sep 05, 2012 | 1999 Oldsmobile Aurora

1 Answer

No Tail lights. Or brake lights(when the headlights are on). HELP!!!


I think you have a bad ground at the back on both rear lights or their earth out on the same connection but these american cars use a funny system where the stop lights are the indicators and not a seperate yellow light like europeon motors ,Now these brake light switches also allow the indicators to work by shutting off the feed to the stop light so it flashes with indicators ,Why american cars use this system i dont know as its so complicated for the stop light switch function but try the ground or earth wire on the back lights and if no joy then ask a american mechanic with experiance of this sort of circuitry as when i get american cars for import i have to fit new back lights and disconnect the brake light switch .

Feb 17, 2012 | Cars & Trucks

2 Answers

1992 Cadillac Brougham 5.0 L V8 RWD, turn signal don't work.


The turn signal switch is most likely the problem,but change the flasher for the turn signals first,some times this is all that it is.

Jun 11, 2010 | 1992 Cadillac Brougham

Not finding what you are looking for?
2002 Ford F250 Super Duty SuperCab Logo

67 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Ron Lankford

Level 3 Expert

5386 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...