Question about 1997 Chevrolet S-10 Pickup

1 Answer

Chevy s10 brake caliper

Hi my name is zach and i need to know if the brake caliper bolts on a 97 chevy s10 are reverse thread

Posted by on

  • Anonymous Mar 17, 2014

    97 chevy s 10 will not crank over all of a sudden

  • Anonymous Mar 23, 2014

    What size is the torx holding the brake calipers on? Sheez....

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 149 Answers

Hey zach, no they are not reverse thread. They are most likely just very tight from the heat and cool cycles they go thru. Put your wrench on them and give it a few sharp raps with a ball peen hammer. That should break them loose enough to finish with the wrench.

Posted on Mar 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What size allen needed to remove break pads


Allen wrenches usually come in a set, try 3/8.

Apr 30, 2016 | 2008 Chevrolet Chevrolet Impala LS

1 Answer

Need to know thread and size of bolts on brake calipers nissan almera 1500 2001


When you buy replacement calipers they usually come with new bolts. If you have the old bolts, use thread gauge or die to check.

Jan 23, 2015 | Nissan Cars & Trucks

1 Answer

How to replace front brake pads on a How to replace front brake pads on a 2000 Chevy S10 4WD pickup?


First you want to remove brake fluid from brake resovoir, raise front wheels off ground and set park brake or block rear wheels. Remove front wheels, keep steering wheel unlocked so you can turn rotors side to side. Loosen bolts that hold caliper end gently pry caliper free from rotor, remove caliper and remove pads, use bungy cord to hang caliper away from rotor, have rotors measured to see if they are thick enough to have machined, replace if out of specs. Match up pads with old ones, use anti- squeak red liquid and put layer on back of pads, let dry. Use tool to put pistons back into calipers, slowly put pistons back into bore while opening up bleeder screw so ABS won't be damaged. After rotors resurfaced, wash with rubbing alchohal to remove any oils from hands, install rotors and reverse putting pads back onto caliper and reinstall, torque caliper bolts to factory specs and tighten bleeder screws. Install wheels, torque lug nuts to factory specs and replace brake fluid in resovoir. Lower car carefully to ground and press brake peddle without pumping it. Any air in system should bleed out, if not get someone to help with bleeding system. Road test to ensure no squeaks or pulling, burn brakes in slowly.

May 10, 2014 | 2007 Saturn Aura XR Sedan

1 Answer

2004 chevy malibu classic caliper torque


caliper mounting bracket bolts torque 85 ft lbs torque caliper bolts 26 ft lbs..

Jul 06, 2013 | Cars & Trucks

1 Answer

97 Chevy S10 rear end squeek that goes away when brakes are applied


If you have rear disc brakes, one of the rotors could be warped and causing the pads to move in the caliper.
You should be able to remove one wheel at a time, lock down the rotor with the lug nuts, and put the trans in low gear or reverse to listen for the noise.

Jan 14, 2013 | 1997 Chevrolet S-10 Pickup

1 Answer

How do I remove the brake roter for my 94 s10 chevy pickup


once tire is off there should be two torx oor allan key bolts behind the caliper, unbolt until able to get caliper off. then using a hammer gently tap on the back of the rotor should come off

Jul 09, 2011 | 1998 Chevrolet S-10 Pickup

1 Answer

When I removed the four bolts holding the brake pad assembly, the longer bolt pulled the threads out Where do I get a replacement bracket ? Also what is the proper name for it ?


This would be the caliper mount that holds the brake caliper and it holds the brake pads. cheapest salvage yard if not try rockauto.com

Feb 16, 2011 | 1988 Toyota Pickup

1 Answer

2000 C1500 lower brake caliper mounting bolt will not loosen. Is it reverse threaded or could it be over torked?


Hello, my name is Ben. That bolt is not reverse threaded. It is most likely just very tight. Soak it with some WD-40 or even better is P-B Blaster for an hour or so and try again. If all else fails, you can VERY CAREFULLY heat it with a small torch. Just be extremely careful with the flame.

Jun 08, 2010 | 2000 Chevrolet Silverado 1500

1 Answer

Is there a torque spec on the spindle nut for the rear caliper on a 1999 Chevy Silverado 4x4 V8 5.3


  1. nstall the caliper mounting bolts. Perform the following procedure before installing the caliper guide pin bolts (15 Series only).
  2. Remove all traces of the original adhesive patch.
  • Clean the threads of the bolt with brake parts cleaner or the equivalent and allow to dry.
  • Apply Red Loctite#272 to the threads of the bolt.
  1. Install the caliper mounting bolts (25 series). Tighten the caliper guide pin bolts to 42 Nm (31 ft. lbs.) on the 15 series; 108 Nm (80 ft. lbs.) on the 25 series.

Nov 19, 2009 | 1999 Chevrolet Silverado 1500

Not finding what you are looking for?
1997 Chevrolet S-10 Pickup Logo

383 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...