Question about 2001 Dodge Ram 1500 Truck 2WD

1 Answer

Abs and brake light stay on continously

Just started recently. checked fluids, recently changed front and rear brakes.

Posted by on

  • yadayada
    yadayada May 11, 2010

    there will be a trouble code stored for the light, have the dealer test the system for that code.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

Could be one of the speed sensors on the front wheels. I believe the sensor comes with the wheel bearing assembly.

Posted on Mar 02, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hyundai trijet just had abs ring changed on passenger front now abs light stays on and hand break light stays on. Help.


If a wire was broken replacing the reluctor ring, this would be the ABS light. Not the brake light. Check the brake fluid, check the E brake pedal/handle. The rings do break, I just weld them back in place. If they are gone, it gets a new axle.

Sep 11, 2016 | 2005 Hyundai Trajet 2.0

2 Answers

2008 wrangler. abs, esp and traction control light staying on. checked brake fluid and fuses


Check first the third eye brake light. does it work? okay the problem reside in a ABS sensor make sure it is hook up or if you recently did a brake job it didnt get contaminated. When the ABS signal is interfered with ESP,Traction is disabled. One or some of the wheel speed sensor is disconnected or is being interfered with. This is common for a recent brake job if any occured

Apr 23, 2011 | 2008 Jeep Wrangler

2 Answers

Abs light on in my ford ranger 1999


ABS light tells you that there is some problem with the brake system like you have forgot to release the emergency brake or its time for you to change the brake fluid. Ford recommends to change the brake fluid every year.If you have recently refilled the brake fluid , check for any leaks.Abs light indicates that your braking system needs to be serviced.

Feb 15, 2011 | Ford Ranger Cars & Trucks

3 Answers

1998 chevy express van 3500 front brakes and rear are new, front calipers are new but ABS light on dash is on, the front brakes smoke after a little while of driving. Thanks Joe


I'd first make sure the new pads are the correct size. Doesn't happen very often but maybe the parts person gave you the wrong size pads ( for the smoking problem). As for the ABS light, most newer cars will throw out codes if you wait too long to change them out, I would contact a chevy dealer or search online about reseting the code (light).

Dec 07, 2010 | 1999 Chevrolet Silverado 1500

1 Answer

Driver side brake not bleeding properly after bleeding left side and changing rotors, calipers, and pads?


first of all make sure master cylinder is full of brake fluid.then you crank car leave foot off brake pedal. watch abs light on dash it should turn off in 10 seconds if not have car towed to garage or dealer. they have to use a scanner to scan the abs brakes if abs light turn off in 3 seconds. then starting bleeding from master bleed the lower brake line fitting at the proportional valve followed by the upper brake line fitting. keep eye on brake fluid in mastercylinder dont let run dry.next prime the abs hydralic modulator.connect the bleeder hose to the rear bleeder valve on the modulator.place the other end into a container partially filled with cleab brake fluid.make sure the end of the hose is submerged.open the bleeder valve slowly about 1/2 to 3/4 turn have an assistant depress the brake pedal and hold it in the depressed position. when the flow of fluid ceases close the bleeder valve.repeat process until no air bubbles are present in the fluid.then tighten the bleed valve securely. start bleeding brakes. your bleeding sequence is right rear - left front - left rear - right front.WARNING IF ALL FAILS YOUR BRAKES DONT FEEL SOLID AND FEEL VERY SPONGY.DONT DRIVE CAR. HAVE IT TOWED TO DEALERSHIP.THEY WILL HAVE TO PRESSURE BLEED YOUR BRAKE SYSTEM.

Nov 17, 2009 | 1999 Oldsmobile Alero

1 Answer

Anti-lock & brake lights are staying on


NO CK FOR WIRES BROKEN TO ABS SENSOR ON TOP OF THE REAR TWO WIRE TERN. & CK SENSOR IN REAR WITH OM METER

May 18, 2009 | 1990 Ford F150

2 Answers

Brake pedel hard,can't get fluid to back brakes,


You need to replace the round Ball (accumulator ball). It's not holding pressure. You have front brake only. Is the pedal hard as a rock, the red brake light stays on, abs light stays on?
Check out this sight. http://www.albeedigital.com/supercoupe/articles/abs-system.html

May 03, 2009 | 1990 Ford Thunderbird

2 Answers

ABS light and alarm constanly on


try changing your pads all round as they have sensors for each set of pads or just try and get a set of sensors

Dec 02, 2008 | 1993 Mazda RX-7

Not finding what you are looking for?
Cars & Trucks Logo

135 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

70346 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6869 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...