Question about 1999 Chevrolet S-10 Pickup

1 Answer

I have a 1999 chevy s10 pick up zr2. the wheel

I have a 1999 chevy s10 zr2 the rear end is a 373 8.5 with posi. the wheel seals are leaking took the diff cover off need to take the Cross Shaft Pin out but its seized to the spider gear. i have tried pounding it out even with an air chisel and heat but nothing seems to be working. now i no that i have to replace the spider gears cause they are shot missing teeth and all but im hoping to get this out without harming anything else. and i cant get the new spider gears without getting the axles out so if you have any ideas i would apprciate it thanks

Posted by on

  • yadayada
    yadayada May 11, 2010

    Call me on this, know this problem well 925-459-0571

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 4 Answers

Easy way- replace whole axel housing from junkyard slice axels with torch or sawsall to remove posi unit then reassemble.sorry cann't think of any other way

Posted on Mar 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

92 Chevy S10, had a fuelpump put in,drive it a couple miles,park it,it smokes underneath,(somewhere around the driver's side back wheel)seems like there's less power,wat do u think it might be?


I wouldn't even drive it, till you figure out the problem. If coming from wheel, check the brakes and parking brake. Is there any oil in the rear end? I can't rule out wheel bearing. I can't tell, at the moment if bearing is sealed or gets lube from rear-end?

Mar 10, 2016 | Cars & Trucks

1 Answer

I have a 2004 Chevy s10 4 door pickup 4 wheel drive rear axle code gu6 and g80 what rear ends interchange with this


ear axle ratio RPO - S-10 Forum

www.s10forum.com/forum/f13/rear-axle-ratio-rpo-12655/

Jul 13, 2002 - 51 posts - ‎41 authors
S10Forum.com is the place to discuss rear axle ratio RPO. ... GU6=3.42. GT4=3.73. GT5=4.10 ... http://www.chevrolet.com/s10/library...ex_chassis.htm .... which trucksusually come with 3.42 from the factory ? ..... On an unrelated note, it looks like I havethe GT4 code in my '98 Blazer 4-door, and the G80. More results from www.s10forum.com

Rear End Ratio RPO Codes Here [Archive] - FSC - Chevy Truck Forum ...

www.fullsizechevy.com > ... > Technical / Maintenance

May 5, 2004 - 100+ posts - ‎100+ authors
I have a 3.08 rear end ratio, I forget the code 4u or something. Then in the next column I ... G80 is the RPO code for the factory locker, not posi ...

How Do I Know My Truck Has A Locking Diff? - 1999-2006 & 2007-2013 ...

www.gm-trucks.com/forums/.../129234-how-do-i-know-my-truck-has-a...

Jan 19, 2016 | Cars & Trucks

1 Answer

Why do I have oil in my breaks of my 1996 Chevy


if your talking about the rear brakes its probably the differential axle seal that is leaking differential oil out of the rear end onto the brake shoes. you will have to pull the rear axle to replace the seal and clean the rear brakes/area with brake cleaner or replace the rear brakes if they are too soaked with brake fluid.

Oct 04, 2014 | Cars & Trucks

1 Answer

Oil leaking trans 1999 chevy S10 replaced torque converter seal leaks at front


ou may need to remove the front pump and replace the seal on the pump and the converter seal as well

Aug 08, 2012 | Cars & Trucks

1 Answer

I got a 1999 chevy silverado 4x4 and the rear end was bad so i put anothr one in it and now when i put it in 4wd it drags to rear tires and i checked the gears and they are the same 373 gear ratio as what...


WELL IF YOU CHANGE THE REAREND THAT DONT HAVE NOTHING TO DO W/PUTTING IT 4 WHEEL DRIVE BECAUSE ITS THE FRONT ONE THAT LOCKS IN . MAYBE YOU BRAKES ARE DRAGGING ON THE REAR END ADJUST BRAKES AN SEE IF THAT HELPS .

Dec 12, 2010 | 1999 Chevrolet Silverado 1500

1 Answer

How to replace rear wheel bearing on 2003 chevy s10 4x4 zr2? My skill level is basic, I do the oil changes and tune-ups on my truck but not to much more. It is a ''Do-ItYourSelf'' jobs or is the maybe...


its not hard but you do have to remove diff cover and then take out spider shaft to remove clips that hold axle. then remove bearing with slide hammer or puller. if bearings are bad so is the axle because its part of the bearing

Jun 20, 2010 | 2003 Chevrolet S-10

1 Answer

I have a 1969 camaro with a 12 bolt posi, when I turn a corner you can feel the wheels skiding as I turn. It acts like a 4 wheel drive on dry pavement, 373 gears posi adative has been added. its like the...


since the wheels are fixed and cant turn your feeling them both want to go straight the inside wheel has a tighter turn than the outside causing the slipping or chattering feeling

Feb 24, 2010 | 1983 Chevrolet Camaro

1 Answer

I have a 1999 Chevy s10 zr2 pickup, when i start it it makes a ticking noise in the engine after it warms up it stops


This is a common complaint. What it is is the a lifter making noise because it has lost its prime (oil that is supposed to stay in the lifter to keep it lubricated). To make the noise stop try using some Lucas Oil Treatment or oil stabilizer. You can pick this up at your local Advance, Napa Auto, or Auto Zone parts dealer.

Hope my advice is helpful and you get your S10 in tip top shape.

Jan 27, 2009 | 1999 Chevrolet S-10 Pickup

Not finding what you are looking for?
1999 Chevrolet S-10 Pickup Logo

468 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...