Question about 2007 Land Rover LR3 V6

Open Question

Transmission fault When driving in low range (low gear ratio) and using my command shift feature together with the terrain response system, I sometimes get the message above which then tells me to stop safely. Then the suspension lowers. If I switch off the engine and restart the engine letting the diagnostics run first, then the error clears and I can continue. The problem is not persistent, but on a recent trip it happened about 10 times in an hour.

Posted by on

1 Suggested Answer

  • 3 Answers

SOURCE: Transmission fault

there is a problem with the rear differential motor actuator,the clutch seems to retract half way back during ingnition cycle procedure...it would require recalibration for simpler cases and a motor actuator  replacement for the more serious cases...has d handler to recalibrate transfer case too.use approved diagnostic equipment e.g. JLR IDS

Posted on Nov 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Dodge caravan


Both error codes you have are transmission related. P0736 is an error for reverse has wrong gear ratio. P0700 is a general transmission problem code
http://www.obd-codes.com/p0700
http://www.obd-codes.com/p0736
for more information.

Mar 22, 2015 | Dodge Caravan Cars & Trucks

1 Answer

Interrogate ecu using atologic P0732 Gear 2 incorrect ratio P07667 shift Sol d


Gear 2 Incorrect Ratio Our emissions expert has put together the following information about the P0732 fault code. We have also included diagnostic procedures you can take to your repair shop if the mechanic is having difficulty analyzing the code.
OBD II Fault Code
  • OBD II P0732
Fault Code Definition
  • Gear 2 Incorrect Ratio
What does this mean?
The purpose of the automatic transmission is to match the engine's optimum power and torque characteristics to the driver's desired rate of acceleration and speed by auto-selecting different gear ratios or 'speeds' to power the wheels.
Code P0732 When the code P0732 is set in the Powertrain Computer, it means that the Powertrain Computer or PCM is seeing a greater than a specified RPM difference between the rotational speed of the Input RPM Sensor and the Transmission Output RPM Sensor when the vehicle is in 2nd gear. This can occur during shifting or when driving at steady speeds. It often implies that the transmission is slipping.
Symptoms
  • Check Engine Light will illuminate
  • Vehicle will not shift properly
  • Decrease in fuel economy
  • In unusual cases, there are no adverse conditions noticed by the driver
  • In some cases, there may be performance problems, such as dying when coming to a stop after driving on the freeway and/or misfire-like symptoms
Common Problems That Trigger the P0732 Code
  • Defective 2nd gear shift solenoid
  • Defective 2nd gear related gear set or clutch pack
  • Defective Engine Coolant Temperature Sensor
  • Defective Valve Body
  • Dirty transmission fluid that restricts the hydraulic passages
Common Misdiagnoses
  • Engine Misfire problem
  • Internal Transmission problem
  • Driveline problem
Polluting Gases Expelled
  • HCs (Hydrocarbons): Unburned droplets of raw fuel that smell, affect breathing, and contribute to smog
  • CO (Carbon Monoxide): Partially burned fuel that is an odorless and deadly poisonous gas
  • NOX (Oxides of Nitrogen): One of the two ingredients that, when exposed to sunlight, cause smog
P0732 Diagnostic Theory for Shops and Technicians
When diagnosing a P0732 code, it is important to record the freeze frame information and then to duplicate the code setting conditions with a test drive. Pay close attention to the engine load, throttle position, RPM, and road speed because a P0732 can be difficult to detect.
One should monitor the RPM input speed and compare that to output speed RPM on a smooth, flat surface after the vehicle is warmed up and the fuel system is in a closed loop. Monitor how the 2nd gear solenoid configuration responds to an increased amount of throttle. The 2nd gear related solenoid should stay in 2nd gear and the transmission should NOT slip.

PO766

Possible causes- Low transmission fluid level
- Dirty transmission fluid
- Faulty shift solenoid D valve
- Shift solenoid D valve harness or connectors
- Shift solenoid D valve circuit is open or shorted
Tech notesWhen the a transmission solenoid is stuck off, in most cases the problem is not the electrical part of the solenoid; the problem is foreign material obstructing the mechanical function of the solenoid or the flow of the fluid through the transmission valve body. If the transmission fluid is very dirty, it is recommend changing the transmission fluid and if possible removing the transmission pan for further diagnosis. Excessive debris or metal particles on the transmission pan could be an indication that there is a transmission mechanical failure and that the transmission will need to be rebuilt or replaced. When is the code detected?The P0766 code is detected when the ECM has detected a mechanical fault with the solenoid energized, valve stuck off P0766 Description Shift solenoid valve D is turned ON or OFF by the Transmission Control Module (TCM) in response to signals sent from the park/neutral position (PNP) switch, vehicle speed and Engine Control Module (ECM) (throttle opening). Gears will then be shifted to the optimum position.

Mar 16, 2015 | 2006 Ford Focus

1 Answer

What does diagnostic code PO0706 and PO700 mean?


OBD II Fault Code
  • OBD II P0706
Fault Code Definition
  • Transmission Range Sensor Circuit Range/Performance
The purpose of the automatic transmission is to match the engine's optimum power and torque characteristics to the driver's desired rate of acceleration and speed by auto-selecting different gear ratios or 'speeds' to power the wheels. The Transmission Range Sensor (also referred to as the PRNDL input and/or neutral safety switch) tells the transmission control module (TCM) and the powertrain control module (PCM) that the transmission is in park, reverse, neutral, drive, low, 2nd, 3rd etc. It is attached directly to the manual valve of transmission, so when the shift lever is moved say from park to drive, the Transmission Range Sensor communicates this critical information to the above mentioned vehicle computer systems.

P0700
Many vehicles have a control module for the automatic transmission called a transmission control module (TCM). The engine control module (ECM) communicates with the TCM to monitor the automatic transmission for faults. If the TCM detects a fault in the automatic transmission and sets a transmission related fault code, the ECM is informed of this also and sets a P0700 in the ECM memory.

May 18, 2013 | 2000 Honda Civic

1 Answer

I need help asap 2003 Expedition code p0171 and code p0712 i have and idea of the 1st code but whats the secound code i really need help i dont want to take it to a shop where there going to charge me alot...


P0700 Transmission Control System

P0701 Transmission Control System Range/Performance

P0702 Transmission Control System -Electrical

P0703 Torque Converter/Brake Switch B Circuit

P0704 Clutch Pedal Position Switch -Circuit Malfunction

P0705 Transmission Range Sensor/Switch Circuit Malfunction (PRNDL Input)

P0706 Transmission Range Sensor/Switch Circuit Range/Performance

P0707 Transmission Range Sensor/Switch Circuit Low Input

P0708 Transmission Range Sensor/Switch Circuit High Input

P0709 Transmission Range Sensor/Switch Circuit intermittent

P0710 Transmission Fluid Temperature Sensor Circuit

P0711 Transmission Fluid Temperature Sensor Circuit Range/Performance

P0712 Transmission Fluid Temperature Sensor Circuit Low Input

P0713 Transmission Fluid Temperature Sensor Circuit High Input

P0714 Transmission Fluid Temperature Sensor Circuit Intermittent

P0715 Input/Turbine Speed Sensor Circuit

P0716 input/Turbine Speed Sensor Circuit Range/Performance

P0717 Input/Turbine Speed Sensor Circuit No Signal

P0718 Input/Turbine Speed Sensor Circuit Intermittent

P0719 Torque Converter/Brake Switch B Circuit Low

P0720 Output Shaft Speed Sensor Circuit

P0721 Output Shaft Speed Sensor Circuit Range/Performance

P0722 Output Shaft Speed Sensor Circuit No Signal

P0723 Output Shaft Speed Sensor Circuit Intermittent

P0724 Torque Converter/Brake Switch B Circuit High

P0725 Engine RPM Input Circuit

P0726 Engine RPM Input Circuit Range/Performance

P0727 Engine RPM Input Circuit No Signal

P0728 Engine RPM Input Circuit Intermittent

P0729 Gear 6 Incorrect Ratio

P0730 Incorrect Gear Ratio

P0731 Gear 1 Incorrect Ratio

P0732 Gear 2 Incorrect Ratio

P0733 Gear 3 Incorrect Ratio

P0734 Gear 4 Incorrect Ratio

P0735 Gear 5 Incorrect Ratio

P0736 Reverse Incorrect Ratio

P0737 TCM Engine Speed Output Circuit

P0738 TCM Engine Speed Output Circuit Low

P0739 TCM Engine Speed Output Circuit High

P0740 Torque Converter Clutch Solenoid Circuit

P0741 Torque Converter Clutch Solenoid Circuit Performance or Stuck Off

P0742 Torque Converter Clutch Solenoid Circuit Stuck On
P0743 Torque Converter Clutch Solenoid Circuit Electrical
Now i dont know a lot about automatics especially modern ones with all this fancy electronics thats used nowdays but i think its a fault with the temperature sensor for the gearbox.But where its located and what it looks like i have no idea it could even be mounted inside the gearbox .Sorry not a very good answer from a mechanic but?? very few of our europeon cars come with auto transmission .Evan when i do know whats wrong i cannot buy the parts for the gearbox as only re-con boxes supplied by the dealer so best advice is to try a specialist in auto box repairs only .PS some of my best students when i used to teach mechanics many moons ago were the girls so no excuses like iam only a girl please

Apr 22, 2013 | Cars & Trucks

1 Answer

Po758 po756


Hi there:
DTC P0756 - Shift Solenoid B Performance or Stock Off

DTC P0758 - 2-3 Shift Solenoid Circuit Electrical



Both fault codes refer at 2-3 shift solenoids problem, firs I suggest make sure the connector on the transmission looks okay and the terminals are not spread. The only other thing in the circuit is the PCM (Powertrain Control Module).


The PCM identifies a 2-3 SS valve performance condition by monitoring the commanded gear versus the gear ratio.

If the PCM detects the gear ratio outside the limits for a particular commanded gear, then DTC P0756 sets.
Case 1
  • The PCM commands 1st gear and the gear ratio indicates 4th gear (0.65:1 to 0.75:1) for 2 seconds and;
  • The PCM commands 2nd gear and the gear ratio indicates 3rd gear (0.95:1 to 1.05:1) for 1 second

Case 2

The PCM commands 3rd gear and the gear ratio indicates 2nd gear (1.52:1 to 1.62:1) for 3 seconds and

  • The PCM commands 4th gear and: the vehicle speed is 35-82 mph; the TP angle is 7-40%; the gear ratio indicates 1.05:1 to 2.97:1 for 3 seconds .


In this links could find description and testing procedure for P0756 and P0758 in PDF file format.


Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Aug 22, 2012 | Chevrolet Cars & Trucks

1 Answer

Fault code po 736 reverse incorect ratio 1996 dodge caravan


DTC P0736 - Reverse incorrect gear ratio

The clutch pressure control (PC) solenoid 2 flows fluid to the 3-5-R clutch when commanded OFF and exhausts fluid when commanded ON. The clutch PC solenoid 2 regulates the transmission fluid pressure to the 3-5-R clutch. The transmission fluid pressure (TFP) switch 1 Opens (High) under fluid pressure and closes (Low) when no pressure is present. The transmission control module (TCM) calculates gear ratio based on data from the automatic transmission input speed sensor (ISS) and the output speed sensor (OSS). The TCM compares the known transmission gear ratio to a calculated gear ratio for each commanded gear.

Circuit/System Verification:
Operate the vehicle to induce a shift from second to third gear while observing TFP Switch 1. Perform this action 2 times. The TFP Switch 1 should change states from Low to High. If the TFP Switch does not change states and no other DTCs set, replace the control solenoid (w/body and TCM) valve assembly. If any other DTCs set, diagnose that DTC first.
Operate the vehicle to obtain sixth gear 2 times and then check for DTCs other than DTC P0736.If any other DTCs set, diagnose that DTC first. If no other DTC sets, continue on with diagnostics.
Operate the vehicle by shifting from Park to Reverse, then while in reverse, operate the vehicle with the calculated throttle position greater than 8% for 5 seconds, perform this maneuver a minimum of 3 times. If the DTC P0736 resets, go to Component Testing.

Component Testing:
Perform the line test procedure.
Inspect the check ball 5 for possible sticking or damage. If you found a concern with this check ball, repair the concern.
Inspect the shift select valve 3 for sticking or damage. If you found a concern with the shift select valve 3, repair or replace the valve or valve body.
Inspect the R-1 (Low and Reverse clutch) assembly for wear or damage. If you found a R-1 assembly concern, repair or replace the R-1 assembly as necessary.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day and Happy New Year.

Dec 29, 2011 | 1996 Dodge Caravan

1 Answer

How can you tell what trans is in 01 grand cherokee laurado 4.0


Here is an article I found talking about the Transmission. The second generation Grand Cherokee: 1999-2004 Jeep WJ The first Grand Cherokee was redesigned in 1999, for lower production cost and greater performance and reliability; it was Chrysler's first use of an electronic bus to replace individual wires throughout the body.

Jeep five-speed automatic transmission

An all-new, electronically-controlled transmission with five forward ratios including an alternate second gear ratio for improved performance for passing and better fuel economy is available with the V-8 only, and was designed specifically for Jeeps.

The transmission features unique characteristics such as a tall, 3.00:1 first gear that gives the driver better initial acceleration. Real-time driver adaptive shifting fine-tunes the shift pattern to the driver, while an alternate second gear ratio gives the driver five forward ratios. During acceleration, second gear has a ratio of 1.67. Depending on speed and throttle position, both this gear and an alternate 1.50 second gear ratio are available for kick-down operation, making the down-shift smoother. Its reverse gear ratio is equal to the first gear ratio, to allow for heavier loads.

Other features include three planetary gear sets that combine the widest range of gear ratios available in any transmission in its class. Combined with precise step selections, this brings smooth shifts and maximum power and optimal fuel economy.

The transmission is built at the Indiana Transmission Plant in Kokomo, Indiana, in an all-new 1.2-million square-foot (110,000 m2) facility.


Mar 01, 2011 | 2001 Jeep Grand Cherokee

1 Answer

My c6 in bronco starts off in 2nd gear performs ok every other way.


P0700 Transm.Contr.System Malfunction 17084
P0702 Transm.Contr.System Electrical 17086
P0703 Torque Converter/Brake Switch B Circ Malfunction 17087
P0705 Transm.Range Sensor Circ.(PRNDL Inp.) Malfunction 17089
P0706 Transm.Range Sensor Circ Range/Performance 17090
P0707 Transm.Range Sensor Circ Low Input 17091
P0708 Transm.Range Sensor Circ High Input 17092
P0710 Transm.Fluid Temp.Sensor Circ. Malfunction 17094
P0711 Transm.Fluid Temp.Sensor Circ. Range/Performance 17095
P0712 Transm.Fluid Temp.Sensor Circ. Low Input 17096
P0713 Transm.Fluid Temp.Sensor Circ. High Input 17097
P0715 Input Turbine/Speed Sensor Circ. Malfunction 17099
P0716 Input Turbine/Speed Sensor Circ. Range/Performance 17100
P0717 Input Turbine/Speed Sensor Circ. No Signal 17101
P0721 Output Speed Sensor Circ Range/Performance 17105
P0722 Output Speed Sensor Circ No Signal 17106
P0725 Engine Speed Inp.Circ. Malfunction 17109
P0726 Engine Speed Inp.Circ. Range/Performance 17110
P0727 Engine Speed Inp.Circ. No Signal 17111
P0730 Gear Incorrect Ratio 17114
P0731 Gear 1 Incorrect Ratio 17115
P0732 Gear 2 Incorrect Ratio 17116
P0733 Gear 3 Incorrect Ratio 17117
P0734 Gear 4 Incorrect Ratio 17118
P0735 Gear 5 Incorrect Ratio 17119
P0740 Torque Converter Clutch Circ Malfunction 17124
P0741 Torque Converter Clutch Circ Performance or Stuck Off 17125
P0748 Pressure Contr.Solenoid Electrical 17132
P0750 Shift Solenoid A malfunction 17134
P0751 Shift Solenoid A Performance or Stuck Off 17135
P0752 Shift Solenoid A Stuck On 17136
P0753 Shift Solenoid A Electrical 17137
P0756 Shift Solenoid B Performance or Stuck Off 17140
P0757 Shift Solenoid B Stuck On 17141
P0758 Shift Solenoid B Electrical 17142
P0761 Shift Solenoid C Performance or Stuck Off 17145
P0762 Shift Solenoid C Stuck On 17146
P0763 Shift Solenoid C Electrical 17147
P0768 Shift Solenoid D Electrical 17152
P0773 Shift Solenoid E Electrical 17157
P0790 Normal/Performance Switch Circ Malfunction 17174

Dec 20, 2010 | 1985 Ford Bronco

1 Answer

Hi sir, i want some details related to the gear


P0700 Transm.Contr.System Malfunction 17084
P0702 Transm.Contr.System Electrical 17086
P0703 Torque Converter/Brake Switch B Circ Malfunction 17087
P0705 Transm.Range Sensor Circ.(PRNDL Inp.) Malfunction 17089
P0706 Transm.Range Sensor Circ Range/Performance 17090
P0707 Transm.Range Sensor Circ Low Input 17091
P0708 Transm.Range Sensor Circ High Input 17092
P0710 Transm.Fluid Temp.Sensor Circ. Malfunction 17094
P0711 Transm.Fluid Temp.Sensor Circ. Range/Performance 17095
P0712 Transm.Fluid Temp.Sensor Circ. Low Input 17096
P0713 Transm.Fluid Temp.Sensor Circ. High Input 17097
P0715 Input Turbine/Speed Sensor Circ. Malfunction 17099
P0716 Input Turbine/Speed Sensor Circ. Range/Performance 17100
P0717 Input Turbine/Speed Sensor Circ. No Signal 17101
P0721 Output Speed Sensor Circ Range/Performance 17105
P0722 Output Speed Sensor Circ No Signal 17106
P0725 Engine Speed Inp.Circ. Malfunction 17109
P0726 Engine Speed Inp.Circ. Range/Performance 17110
P0727 Engine Speed Inp.Circ. No Signal 17111
P0730 Gear Incorrect Ratio 17114
P0731 Gear 1 Incorrect Ratio 17115
P0732 Gear 2 Incorrect Ratio 17116
P0733 Gear 3 Incorrect Ratio 17117
P0734 Gear 4 Incorrect Ratio 17118
P0735 Gear 5 Incorrect Ratio 17119
P0740 Torque Converter Clutch Circ Malfunction 17124
P0741 Torque Converter Clutch Circ Performance or Stuck Off 17125
P0748 Pressure Contr.Solenoid Electrical 17132
P0750 Shift Solenoid A malfunction 17134
P0751 Shift Solenoid A Performance or Stuck Off 17135
P0752 Shift Solenoid A Stuck On 17136
P0753 Shift Solenoid A Electrical 17137
P0756 Shift Solenoid B Performance or Stuck Off 17140
P0757 Shift Solenoid B Stuck On 17141
P0758 Shift Solenoid B Electrical 17142
P0761 Shift Solenoid C Performance or Stuck Off 17145
P0762 Shift Solenoid C Stuck On 17146
P0763 Shift Solenoid C Electrical 17147
P0768 Shift Solenoid D Electrical 17152
P0773 Shift Solenoid E Electrical 17157
P0790 Normal/Performance Switch Circ Malfunction 17174

Dec 20, 2010 | 2006 Renault Fuego

1 Answer

Transmission fault


there is a problem with the rear differential motor actuator,the clutch seems to retract half way back during ingnition cycle procedure...it would require recalibration for simpler cases and a motor actuator  replacement for the more serious cases...has d handler to recalibrate transfer case too.use approved diagnostic equipment e.g. JLR IDS

Mar 02, 2009 | 2005 Land Rover LR3

Not finding what you are looking for?
2007 Land Rover LR3 V6 Logo

Related Topics:

33 people viewed this question

Ask a Question

Usually answered in minutes!

Top Land Rover Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

yadayada
yadayada

Level 3 Expert

61037 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Land Rover Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...