Question about 1997 Mercury Villager

2 Answers

I want to make my 1999 Mercury Villager Sport into a cargo loader, with just the front seats kept and the rest of the back empty. How do I remove the other 3 seats? So far, I can't get any of them to budge from their tracks.

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mercury Master
  • 4,369 Answers

The middle seats come out easily. There are 2 handles you have to lift up on each of the bucket seats, they are in the front of the seat down by the seat tracks. After you lift them, tilt the seat upward in the front and rotate them backward. Then lift out of the hooks. Each seat is held down by 4 hoks.

The 3rd row seat is not designed to come out xcept by a technician. It does slide forward all the way up to the front seat. It has a sliding seat track.
First, lift the T handle under the seat cushion on the left front side of the seat. This will allow you to lift the seat bottom up all the way to lcok in the full up position.
Then, lift the lever on the same side of the seat and slide the seat forward. It will stop in 4 places.
Rear -Rear
6 inches forward of that.
another two ft to the second row seating position
full frward against the front seats.

Pleae rate as fixya if this helps.

I want to make my 1999 Mercury Villager Sport into - c4253aa.gif Seat —Third Row Bench Removal
sxv~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Removal of the third row bench seat requires more than one technician.

  1. Remove the second row seats. For additional information, refer to Seat—Second Row .
  1. Remove the floor mats.
  1. Lock the seat cushion in the upright position.
    1. Lift the handle to release the cushion.
    1. Lock the seat cushion in I want to make my 1999 Mercury Villager Sport into - 0235766.gif position.
0235766.gif
  1. Move the third row bench seat to the second row position.
    • Lift the seat track release handle.
  1. Remove the two bolt covers.
  1. Remove the two seat track front bolts.
  1. Remove the four seat track rear bolts.
    1. Position the rear seat cushion floor cover aside.
    1. Remove the four seat track rear bolts.
  1. Remove the third row bench seat.

Posted on Mar 10, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Looking to buy a 3rd row bench seat..please let me know if anyone has and willing to sell....thanks

mstqat@hotmail.com

Posted on Dec 11, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Trying to find a picture if where the fuel pump for my 1999 mercury villinger


the fuel pump is INSIDE your fuel tank. the tank has to be removed to replace the pump

Nov 22, 2011 | 1999 Mercury Villager

2 Answers

My 1999 mercury villager ac works in the front but no cold air blows in the back. What needs to be fixed?


it needs to have the rear expansion valve to be inspected for metal, if clean repl expansion valve and recharge a/c

May 20, 2010 | 1999 Mercury Villager

1 Answer

1999 Villager: My 1999 mercury villager ac works in the front but...


you could just be low on freon. Add 1 can & see what happens.
Usually the rear works but not the front. I'm assuming the blower works back there.

It could also be the rear control for hot/cold. You can get an assembly at slavage yard for $10.

i have an extra if you find that is the failure.

go here and our team will help for free.

http://groups.yahoo.com/group/villagerquest/

May 18, 2010 | 1999 Mercury Villager

1 Answer

How do I replace the door lock actuator on a 1999 Mercury Villager w/o damaging the connecting rods and door track?


SECTION 501-14A: Handles, Locks, Latches and Mechanisms 1999 Villager Workshop Manual REMOVAL AND INSTALLATION Actuator —Power Door Lock, Front Removal
  1. Remove the front door latch. For additional information, refer to Latch—Front Door .
  1. Remove the power door lock actuator from the front door latch.
    1. Release the locking tabs.
    1. Remove the power door lock actuator from the front door latch.
583b623.gif
go here too

http://groups.yahoo.com/group/villagerquest/

Sep 26, 2009 | 1999 Mercury Villager

1 Answer

Need to lower the height of the front passenger seat.


It would be difficult to do your self. I think you would need a shop that does handicapp vehicle modifications to do it. The seat is only held on by 4 bolts, but I don't see a way to lower the seat.

May 17, 2009 | 1999 Mercury Villager

1 Answer

How to remove the back seat from my 1998 Mercury Villager


it is not designed to be removed. It is designed to slide back and forth as needed.

Section 01-10: Seats and Tracks 1998 Villager Workshop Manual
REMOVAL AND INSTALLATION Seat, Rear Bench
Removal
  1. Remove the center seat(s) if equipped. Refer to the procedure in this section.
  1. Slide the bench seat forward to the center row seating position.
  1. Use a flat-blade screwdriver to remove the cover caps from the front of the rear seat cushion latch cover.




  1. Remove the two rear seat bolts from the front of the rear seat cushion latch cover.




  1. Lift the rear seat cushion floor cover on the back of the rear bench seat and remove the two inboard rear seat bolts and the two outboard rear seat bolts.




  1. Remove the bench seat from the vehicle through the body side door opening.

Apr 30, 2009 | 1998 Mercury Villager

3 Answers

Rear seat removal 2000 merc Villager


fold top seat down first
then there is seat clip push seat forward with upward motion
this releases back floor clamps once released pull seat back this releases the front clamps then pull seat out of back door

Jul 06, 2008 | 2000 Mercury Villager

Not finding what you are looking for?
1997 Mercury Villager Logo

1,226 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Ron Lankford

Level 3 Expert

5386 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...