Question about 1993 Subaru Legacy

1 Answer

Replacing the front axle on a 93 subaru legacy

I need to replace the driver's side front axle on my 93 legacy. The last time I tried, I could not separate the axle from the hub assembly. What type of puller can be used to separate the axle from the hub? Do you need any special tools to put the new axle into the hub assembly?
Thanks,

Posted by on

  • Anonymous Mar 24, 2014

    Setting the timing on a Subaru legacy 93

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 382 Answers

When I replace the axle halves, I run the Nut off till it is level with the shaft end. THen take a piece of wood and set it across the shaft and hit the wood with a hammer. Usually only takes one or two hits and pops right out.Then I remove the nut and finish removal . Hope this helps, Good luck and have a great day.

Posted on Mar 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Have gear oil leaks under transmission in two holes next where the axel meets on each side


Keith the seals will need replaced, take into a shop and have a tech give estimate for repair. Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
half shaft seal replacement Google Search
How To Install Replace Front CV Axle Shaft 2002 09 GMC Envoy and XL XUV
Part 1 How To Replace Front Axle Shaft Seal RH Front Chevy GMC
CV axle replacement Subaru Outback 2000 Legacy Forester Install Remove...


May 04, 2016 | Cars & Trucks

2 Answers

Hi there I want to know if the SVX cv axle is same axle as the impreza, legacy and forester? Thanks


Yes the early subaru's all use the same front and rear axles
Fronts are easy to change. rears are not.
The only difference in the early style axles that use pin on inner joints are the outer joints with abs rings.

Nov 23, 2014 | 1994 Subaru SVX

1 Answer

Will the axle off of my 91 subaru legacy work on my 93 subaru loyale


Even if it works ( it don't ) I would put a new half shaft on the 93 S-R.

Jan 23, 2013 | Subaru Loyale Cars & Trucks

2 Answers

Need to replace a seal on transmission for a subaru legacy 1991 do i need to remove the whole transmission


are u talking about the front main seal? if so ,yes u have to take the trans. out to replace

Sep 06, 2012 | 1991 Subaru Legacy

2 Answers

We have a Subaru Legacy GT, Twin Turbo 93, the car cut out and will not start, no fault codes, replaced spark plugs, fuel filter, checked the fuel pump, replaced air flow meter, engine temperature sensor,...


sounds like your timing may be off, or have a crank shaft postion sensor failing, when it cuts are you losing spark completely? do you have a fuel pressue gauge? whats the pressure? also you could try running it with the map sensor unplugged and see if the condition improves

Jul 31, 2011 | 1993 Subaru Legacy

2 Answers

Grinding noise passenger side front


Check wheel bearing.
Check backing brake plate , sometimes it's bended and touching brake rotor.
If wheel bearing is bad , you may have same effect with backing plate , brake rotor touch backing plate.

Jun 01, 2010 | 1991 Subaru Legacy

1 Answer

Removing front rotar


rotar doesn't contain the studs, the plate/hub behind the rotar does - you need a 32mm socket to undo the axle nut to then get at the hub (need a flat screw driver to lever the nut tang up first). If it's seized on put the rotar and wheel back on (leave the axle nut off) and gently rock it in a top-bottom motion (not radially or axially) to free it up. you can then gain access to the hub and studs. put the wheel nuts back on the studs 2 -3 turns so that you have a 'seat' and using a bolt with a smaller dia to punch them out

May 08, 2010 | 1991 Subaru Legacy

2 Answers

93 Subaru Legacy front suspension problem after CV joint replaced


the air bag is not ok, this is exactly what they do when they have a leak, these air bags are shot at about 100,000 miles, they start to leak at the creases, u will see cracks there.

Mar 26, 2009 | 1993 Subaru Legacy

3 Answers

Subaru vibration


I had similar problem with my '99 outback. Replaced the front half shafts and seemed much better. A few months later seemed to be comming back so replaced the driver side shaft again and the problem disappeared. I had put in rebuilt shafts and the driver side shaft was not rebuilt correctly.

Feb 21, 2009 | 1999 Subaru Legacy

Not finding what you are looking for?
1993 Subaru Legacy Logo

648 people viewed this question

Ask a Question

Usually answered in minutes!

Top Subaru Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Subaru Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...