Question about 2006 Chevrolet Malibu Maxx

2 Answers

Car won't start , won't turn over

Engin won,t turn over, it show a car with apad lock going through the car on the display 2006 malibu

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers

All you have to do is either pop the hood of the car with the key out of the ignition. Or get out of the car, relock the car and then unlock it mulitple times, should start right up.

Posted on Apr 08, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,533 Answers

It sound as if there is a problem in your security and i would give this a try take the positive side off the battery for about 3-ses and then put it back on to see if it clears the computer

Posted on Mar 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What does a car with a lock light mean


Chevrolet Malibu Questions - SECURITY SYSTEM LIGHT ...

www.cargurus.com > Questions > Chevrolet > Malibu

CarGurusFeb 3, 2014 - SECURITY SYSTEM LIGHT COMES ON - CAR TURNS OVER WON[T START ... Insert the ignition key into the driver door lock. ... When I start my car 3 keys programmed pops up on my dashboard what does that mean.

Chevrolet Malibu Questions - Why does the anti theft system ...

www.cargurus.com > Questions > Chevrolet > Malibu

CarGurusFeb 23, 2011 - Why does the anti theft system keep tripping on my 03 malibu - Every other day my anti-theft system goes off in my car then I have to reset it. It's not ha... ...it needs a pass lock sensor/ ignition lock cylinder. 10 out of 10 people think ... Wait 10 minutes until the light stops flashing, then start. Repairs could run ...

No Start Due to Failed Passlock Sensor : Chevrolet Malibu ...

repairpal.com > Problems > Chevrolet > Malibu

Jan 13, 2016 | 2005 Chevrolet Malibu Maxx

1 Answer

Lifters/car not starting


Do you have the 2.2 liter Ecotec 4-cylinder engine, the 3.5 liter V6, or the 3.9 liter V6 engine? If you have the 2.2 liter engine, there may be a camshaft/timing chain issue if you skipped a tooth when you put the chain back on the cams. If it's a 3.5 or a 3.9 liter V6, you may have incorrectly installed the push rods back into the engine. 3.5 liter intake push rods are approx 5 3/4" long, while the exhaust push rods are approx 6" long.
The 3.9 liter intake push rods are approx 5.81" long, while the exhaust push rods are approx 6.1" long. If you mix the two lengths up when you put them back in the engine, you're going to have problems.

Oct 19, 2013 | 2006 Chevrolet Malibu

1 Answer

Trail blazer gear shift button


Could be the brake switch or the shift lock solenoid. You may be able to turn the key lock to the unlock position, move the shifter out of park, then start the engine in neutral.
The shifter and the shift lock solenoid would need to be inspected.

Jun 19, 2013 | Cars & Trucks

1 Answer

2001 Chev Malibu. Turn key on to start car, won't start. No warning lights on no lights on gauge panel. Radio works, dome light work.


check the ground leg to your engine.. it runs off the neg. battery terminal. will connect to frame and engine.. pull it off, wire brush it put it back.. you radio will work, 'cause it draws much less current, and is grounded in dash.

Jan 11, 2013 | 2001 Chevrolet Malibu

1 Answer

Ignition locked


The ignition lock cylinder tumblers get in a bind all the time on GM vehicles. It probably has little to do with inseting the wrong key. Try inserting the correct key and "jiggle" the key in the lock. You may have to jiggle it up and down and rotate (or try to rotate) the lock cylinder forward and backward. It will probably work just fine if you can wiggle it with just the right combination. If not, you may have a damaged lock cylinder and you will have to replace it. - most likely nothing you did....I change at least two or three of these things every week...VERY COMMON.

Nov 26, 2011 | 2006 Chevrolet Malibu

1 Answer

I have a 2006 Chevrolet Malibu and today I change the filter and oil , and it still marking change oil sign.


Turn the key on (do not start the engine) ,now depress the gas pedal to the floor 3 times, now turn the key off. Now start the car and see if the light is off. If not, just try it again.

May 10, 2010 | 2006 Chevrolet Malibu

2 Answers

I cannot get the Change Oil Soon message to reset on a Pontiac G6


Chevrolet Malibu, Malibu Maxx 2004-06; 2006 HHR, Cobalt, Pontiac G6, Solstice
Turn ignition to run engine off. Display OIL LIFE RESET in the Driver Information Center (DIC). Press and hold the ENTER button for at least one second. An ACKNOWLEDGED’ display message will appear for three second or until the next button is pressed. This will tell you the system has been reset. Turn the key to OFF. If the “CHANGE ENGINE OIL” message comes back on when you start your vehicle, the engine oil life system has not reset. Repeat the procedure.

Jul 17, 2009 | 2007 Pontiac G6 GT Convertible

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

292 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...