Question about 1986 Ford F150 SuperCab

2 Answers

Signals and warning lights!!

My 99 f150 turn signals work but some times they dont. when i turn right it has a quick clicking sound. also the hazard lights do not come on at all. I just replaced the signal bulbs because of this and it still doesnt work. I CANT GET MY TRUCK INSPECTED!!!!!!!!!!!!!!!!!!!

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Ford Master
  • 783 Answers

You have a bad multifunction switch.It is not hard to replace just remove the bottom cover on steering column and top should raise up enough to get to the 2 screws holding the switch on.If you can not get enough clearance with top cover on then you will have to remove lock cylinder to get it off.Just turn key to on postion then look under the lock cylinder part of steering column and you will see a small hole.Stick a small screw driver or pic into the hole and push the pin then remove lock cylinder.

Posted on Mar 01, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 70 Answers

Turn signal switch

Posted on Mar 01, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where is the emergency flasher relay located on 2013 Rogue?


Here is what the service manual says. Looks like it is not a flasher relay but a function of the body control module.

TURN SIGNAL AND HAZARD WARNING LAMP SYSTEMSystem Description OUTLINE Turn signal lamp and the hazard warning lamp is controlled by combination switch reading function and the flasher control function of BCM.
TURN SIGNAL LAMP OPERATION - BCM detects the combination switch condition by the combination switch reading function. - BCM supplies voltage to the right (left) turn signal lamp circuit when the ignition switch is turned ON and the turn signal switch is in the right (left) position. BCM blinks the turn signal lamp.
HAZARD WARNING LAMP OPERATION BCM supplies voltage to both turn signal lamp circuit when the hazard switch is turned ON. BCM blinks the hazard warning lamp.
TURN SIGNAL INDICATOR LAMP AND TURN SIGNAL SOUND OPERATION - BCM transmits the turn indicator signal to the combination meter with CAN communication while the turn signal lamp and the hazard warning lamp are operating. - Combination meter outputs the turn signal sound with the integrated buzzer while blinking the turn signal indicator lamp according to the turn indicator signal.
HIGH FLASHER OPERATION (FAIL-SAFE) - BCM detects the turn signal lamp circuit status by the terminal current value. - BCM increases the turn signal lamp blinking speed if the bulb or harness open is detected with the turn signal lamp operating. NOTE: The blinking speed is normal while operating the hazard warning lamp.

Oct 13, 2014 | 2013 Nissan Rogue

1 Answer

I have an 02 kia sportage. my signal lights come on but dont blink outside. no lights for the signal lights come on on the dash at all. also, no hazard lights.


If the 15A HAZARD fuse in the passenger compartment fuse box is OK, power is getting to the hazard function of the flasher unit. Pressing the hzard switch should cause the hazard lights to flash. HOWEVER, there is an electronic time and warning indication system module connected to to the hazard switch lead and that may be affecting things. If the 10A TURN fuse is OK, power is applied to the turn switch (with the engine in START or RUN) and you state you can select a right or left turn. HOWEVER, the RED/WHT and RED/BLU outputs from the flasher unit connect directly to the front and rear turn lamps and the instrument cluster turn indicators so you are not getting any flasher output. Again, that electronic time & warning indication system module could be affecting things

Oct 26, 2012 | Cars & Trucks

1 Answer

Where is the turn signal relay, hazard relay, and flasher for a 2003 Ford F150? My turn signals do not work (inside or outside), but 3 out of 4 outside lights work when the hazards are on, but with only 1...


It is not the flasher if the hazards work, it is 1 flasher for both turn signals and the hazard lamps. It is in a relay block ( along with the blower motor relay ) under the dash, about in line with the steering wheel column ).

Try tilting the steering wheel all the way up, and test again.

The other quick test is to cycle the hazard switch a few times, to see if it cleans the contacts for the turn signal on the MFS,

Apr 01, 2010 | 2003 Ford F150 Regular Cab

5 Answers

Turn signals are working but the hazzards will not


check the cabel..
check the hazard switch..

if two of them working properly your hazard sould be work...

Nov 04, 2009 | 1998 Ford F150 Regular Cab

2 Answers

99 Chevy Tahoe... Rear turn signals, brake lights, and hazards


I had this problem, and to be honest, it happened to the left side about a week later...it's the board that the bulbs plug into...it's a very common problem with this model. So popular that you can normally get the socket board off the shelf at a parts store! it's extremely simple to replace, and I replaced all the bulbs at the same time!

Oct 10, 2009 | 1999 Chevrolet Tahoe

2 Answers

Turn signals on 2002 Beetle


you need to rplace hazard light switch as this sounds like a relay problem

Aug 13, 2009 | 1998 Volkswagen Beetle

2 Answers

Help please


replace turn signal sw ford 35.00

Mar 01, 2009 | 1999 Ford F150 Regular Cab

1 Answer

2004 F150- Hazard Flashers dont work, turn signals do work


try replacing the hazard relay it should be under the dash try turning it on and off with your head down by the floorboard to pinpoint the right relay and the location. you should be able to hear it easily. hope this helps.

Dec 04, 2008 | 2004 Ford F150

3 Answers

No turn signals or brake lights on left and right but brake light on top


I agree. My brake light dont work. Only the third brake light does. The running lights work but when i apply the brakes the rear tails dont light up.
I currently have this issue along with the signals dont work unless I bang the top of the steering colum. The hazard switch doesnt work either. If the signals dont work it makes this very quick clicking sound on the passenger side. I checked the fuses and they are good. The bulbs still work. The brake switch works cause the third brake light goes on. And seeing as I am having a problem with signals.....GM says I have to replace the switch in the steerg colume. Its a little box about the size of a cigarette pack. If you take apart the panels off ( right behind the steering wheel, where the hazard switch is) ...that is where it is located. Its plugged into the signal lever. Hope this helpa....Good luck everyone with this issue.

Oct 17, 2008 | 2001 Chevrolet Blazer

3 Answers

Turn signals wont work


replace the hazard fuse under the dash any repair shop can heklp you with it

Aug 31, 2008 | 1999 Mitsubishi Eclipse

Not finding what you are looking for?
Cars & Trucks Logo

231 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...